Digital Dispensary

Product Sections


Best Sellers

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

13.70

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Diaphragm Kit for Solex 32PBI-2

Diaphragm Kit for Solex 32PBI-2

18.80

Application: Series 1 1600cc & 2.0ltr petrol (gasolene).

Description: Diaphragm kit for accelerator pump

find out more

Contact Breakers Lucas 25D

Contact Breakers Lucas 25D

4.13

Application: Lucas 25D 4cylinder distributor as fitted to Series 2A and early Series 3 petrol engines, also used on late Series 1 engines with the DM2 distributor.

Description: Lucas boxed contact breaker set also known as 'points'.

Original part number 269987.

find out more

Flexible Fuel Pipe

Flexible Fuel Pipe

39.06

Application: Series I models with petrol engines.

Description: Reproduction flexible fuel pipe with one male end and one female end. Runs from fuel pipe towards carburettor. Now with ethanol proof lining!

Approximate dimensions: Overall length 39cm(15.3")

find out more

Axle Set of Brake Shoes - 10"

Axle Set of Brake Shoes - 10

33.94

Axle set of 4 10inch brake shoes by Mintex plus 4x pull-off springs, 6x imperial brake drum screws, 2x metric brake drum screws, 2 locking plates and 4 screws for anchor plates.

Application: Series1 80", 86" & 88" front and rear axles, Series 2/2A SWB front and rear, Series3 SWB front and rear to June 1980, Series3 SWB rear only from July 1980, Defender 90 rear to 1994.

Previous part numbers for shoes: RTC3411, GBS728, 505675, 505676
find out more

Replacement Condensor for Lucas 25D

Replacement Condensor for Lucas 25D

2.68

Application: Lucas 25D 4cylinder distributor as fitted to Series 2A and early Series 3 petrol engines.Also used on late Series 1 engines.

Description: No longer Lucas boxed condensor as the Lucas ones have a different connector on lead now that makes fixing ackward. So now sourcing from good after market source to original style of Lucas unit!

Approximate dimensions: overall diameter 17mm (0.67 inches), lead 57mm (2.24 inches).

Original part numbers 269988, 245007. DCB101, GSC101

find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Spark Plug Champion N5C

Spark Plug Champion N5C

2.14

Application: Series 2A and Series 3 4 cylinder engines with 7:1 compression ratio and all 6 cylinder Series engines. Also applicable to Series 1 engines.
Description: Champion N5C spark plug, original equipment.
Supersession of Series 1 part number 262796.
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.91

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Axles and Transmission Parts
Page:   <<   <  1  2  3  4  5  ...   >   >>
Bearing for Front Half-Shaft Ref: 55713
Application: Series 1 80" 1948 to 1953

Description: Support bearing for front half shaft. Early Series1 only.

Bearing dimensions: Outside diameter 3"(76mm), inside diameter 1 3/8"(34.9mm), thickness 11/16"(17.5mm)

Bearing number: RLS11


Price: 31.17 (37.40 Including VAT at 20%)




People who bought this item also bought:
1. Gasket for Differential to Axle Casing (Ref: 7316)
2. Retainer for Rear Hub Bearing (Ref: 7297L)
3. Hub Bearing Rear (Ref: 270604)
Bearing for Front Half-Shaft
Bearing for Front Half-Shaft Ref: 244150=
Application: Series 1 1954 onwards, 2 & 3 front axles.
Description: Branded single row roller bearing for supporting front half shaft in end of axle tube.
Approximate dimensions: outside diameter 76.4mm (3"), inside diameter 35mm (1.375"), length 18.5mm (0.73").

Price: 35.08 (42.10 Including VAT at 20%)




People who bought this item also bought:
1. Replacement Swivel Pin Kit for S2A & S3 (Ref: SWIVELPINKIT02)
2. Genuine One Shot Swivel Housing Grease (Ref: STC3435)
3. Universal Joint for Front Half-Shafts (Ref: RTC3690)
Bearing for Front Half-Shaft
Universal Joint for Front Half-Shafts Ref: RTC3690
Application: Series 1 1952 onwards, Series 2 & 3 front axles.
Description: GKN boxed universal joint for front half-shafts.
Approximate dimensions: 75.5mm (3") across caps, 27mm (1.06") diameter caps.
Original part number: 242521

Price: 12.00 (14.40 Including VAT at 20%)




People who bought this item also bought:
1. Replacement Drive Flange 10 Spline (Ref: 571235D)
2. Seal Axle Tube (Ref: 217400)
3. Exhaust Mounting Rubber (Ref: 217608)
Universal Joint for Front Half-Shafts
Bush for Front Stub Axle Ref: 217354
Application: Series 1 and early Series 2.

Description: Bronze bush in stub axle to support outside end of front halfshaft. This bush
should be reamered, after fitting, to 1.250 in. +0.004 in. (31,75mm + 0,10mm).
Manufactured from SAE 660 Bearing Bronze, this bearing bronze alloy resists
many chemicals and is recommended for medium speed, medium load applications.

Approximate dimesions: Outside diameter 55mm(1 3/8"), inside diameter 32mm(1 1/4"), depth 19mm(3/4").

Price: 17.37 (20.84 Including VAT at 20%)




People who bought this item also bought:
1. Gasket for Differential to Axle Casing (Ref: 7316)
2. Retainer for Rear Hub Bearing (Ref: 7297L)
3. Bearing for Front Half-Shaft (Ref: 55713)
Bush for Front Stub Axle
Locker Swivel Pin Retaining Nuts 3/8" diameter Ref: 270287
Application: Series 1 swivel pin housings and early Series 2 ones.

Description: Locker for 3/8" diameter swivel pin retaining nuts.

Price: 0.40 (0.48 Including VAT at 20%)



Locker Swivel Pin Retaining Nuts 3/8
Stud - Swivel Pin Housing Ref: 90508152
Application: Series 1 and early Series2 and 2A.

Description: Stud for retaining top and bottom swivel pins. 3/8" BSF with overall length of 1 7/8" (47.6mm). Used in conjunction with 90508153.

Previous part number 508152

Price: 3.10 (3.72 Including VAT at 20%)




People who bought this item also bought:
1. Pack of 10 1/2" BSF Nyloc Nuts (Ref: 251324x10)
Stud - Swivel Pin Housing
Special Stud - Swivel Pin Housing Ref: 90508153
Application: Series 1 and early Series2 and 2A.

Description: Special stud for retaining top and bottom swivel pins. 3/8" BSF with overall length of 1 7/8" (47.6mm), but with central unthreaded part 10.1mm(0.4") diameter to give exact fit for pins. Used in conjunction with 90508152.

Previous part number 508153

Sorry, currently we have no supplier for these.

Price: 1.85 (2.22 Including VAT at 20%)


Special Stud - Swivel Pin Housing
Swivel Pin Conversion Kit Ref: 532268D
Application: All Series 1 models and Series 2 where fitted with the sprung cone top swivel pin.

Description: Replacement kit to convert sprung cone type top swivel bearings to the later style 'Railko' bush type. This kit converts both top swivel bearings on the front axle.

Price: 37.54 (45.05 Including VAT at 20%)




People who bought this item also bought:
1. RH Rear Wheel Cylinder S1 80" (Ref: 232078D)
2. LH Rear Wheel Cylinder S1 80" (Ref: 232077D)
3. Pair of Front Wheel Cylinders (Ref: 212912/3)
Swivel Pin Conversion Kit
Replacement Swivel Housing S1, S2a & S3 Ref: 539741D
Application: Series 1, Series 2 & 2A, Series 3 (except 109 V8).

Description: Replacement swivel housing for front axle with chrome finish.

Original part number: 234789.

Price: 80.60 (96.72 Including VAT at 20%)




People who bought this item also bought:
1. Swivel Pin Bearing (Ref: 217268+)
Replacement Swivel Housing S1, S2a & S3
Swivel Pin Bearing Ref: 217268+
Application: Series 1, 2 & 3.
Description: Timken or NTN taper roller bearing depending on availability. Fitted to lower swivel pin on front axle.
Approximate dimensions: outside diameter 54mm (2.13"), inside diameter 19mm (0.75")

Price: 11.50 (13.80 Including VAT at 20%)




People who bought this item also bought:
1. Universal Joint for Front Half-Shafts (Ref: RTC3690)
2. Steering Relay (Ref: NRC1269D)
3. Bolt, Steering Relay to Chassis (Ref: BX605281)
Swivel Pin Bearing
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Axles and Transmission Parts
Page:   <<   <  1  2  3  4  5  ...   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Alignment Pins

Alignment Pins

53.27

Application: Freelander 2 and Evoque.

Description: Pair of pins for aligning front subrame to bodyshell.

Approximate dimensions: Overall length 168mm(6.6"), pin diameter 20mm(0.8")

find out more

Rear Lens Right Hand

Rear Lens Right Hand

47.04

Application: Range Rover Classic.

Description: Reproduction rear lamp lens with fog guard.

Approximate dimensions: Height 22.8cm(9"), width 14.3cm(5.6"), thickness 1.8cm(0.7")

find out more

Clamp for Disributor

Clamp for Disributor

18.60

Application: Series 1, Series 2 and Series 3 petrol models.

Description: Clamp for retaining distributor.

Approximate dimensions: Internal diameter 36mm(1.4"), thickness 3mm(0.12")

find out more

6 Way Junction Box

6 Way Junction Box

22.80

Application: All Series 1 models.

Description: Reproduction 6 way junction box.

Approximate dimensions: Overal diameter 54mm(2.1"), height 37.5mm(1.5")

find out more

Fuse Box Series 1

Fuse Box Series 1

34.54

Application: All Series 1 models.

Description: Reproduction 1 way fuse box, needs glass fuse.

Approximate dimensions: Length 54mm(2.1"), width 33mm(1.3"), height 45mm(1.9")

find out more

TDC Alignment Plate

TDC Alignment Plate

120.43

Application: 2.0 I4 MID DOHC AJ200 engine as used in Evoque and Freelander 2.

Description: Alignment plate for setting Top Dead Centre for this engine.

Approximate dimensions: 25cm(9.8"), x 20cm(7.9") x 0.8cm(0.31")

find out more

Thrust Bearing Assembly

Thrust Bearing Assembly

27.90

Application: Fairey overdrive for LT76 gearbox.

Description: Thrust bearing assembly for input shaft. Chamfered plate to clear radius on shaft step.

Approximate dimensions: Overall diameter 1-7/8"(47.6mm), inside diameter 30.8mm(1.21"), thickness of assembly 6mm(0.24")

find out more

Aligner for Balance Shaft

Aligner for Balance Shaft

78.14

Application: 2.0 I4 MID DOHC AJ200 engine as used in Evoque and Freelander 2.

Description: ool for aligning the balance shaft of this engine.

Approximate dimensions: Overall length 84mm(3.3"), flange diameter 70mm(2.75"), body diameter 44mm(1.73").

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -