Digital Dispensary

Product Sections


Best Sellers

Brass Nut 5/16"BSF

Brass Nut 5/16

1.66

Application: Series1 exhaust manifold.

Description: Brass nut 5/16"BSF for holding downpipe to exhaust manifold.

Approximate dimensions: 3/8"(9.5mm) high, 17/32"(13.5mm) across flats.

find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Ignition Coil

Ignition Coil

30.11

Application: Series 1 and Series 2.
Description: Reproduction ignition coil with screw in high tension connection. Supplied with acorn nut and split washer.
Approximate dimensions: Body diameter 54.8mm(2.2"), height 15cm(5.9")
find out more

Stud for Exhaust Manifold

Stud for Exhaust Manifold

1.85

Application: Series 1 1.6 and 2.0 litre, Series 2 2 litre.

Description: Stud to hold downpipe to exhaust manifold.

Approximate dimesions: 5/16"BSF threads to both ends, overall length 1.25"(32mm)

find out more

Black High Tension Lead, Copper Cored

Black High Tension Lead, Copper Cored

1.86

Application: Series One and Series Two
Description: Black high tension cable for spark plugs. 7mm(0.28") outside diameter with 19 strand copper core.

Sold by the metre
find out more

Rocker Cover Gasket

Rocker Cover Gasket

7.72

Application: 1.6ltr and 2.0ltr petrol (gasolene) engines.

Description: Gasket for rocker cover to cylinder head.
find out more

Gasket Exhaust Manifold to Down Pipe

Gasket Exhaust Manifold to Down Pipe

0.96

Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Axles and Transmission Parts
Page:   <<   <  6  7
Key Washer for Hub Bearing Ref: 217352D
Application: Series 1, Series 2 & Series 3.
Description: Thick keyed washer between outer hub bearing and lock nut.
Approximate dimensions: outside diameter 56mm (2.2"), inside diameter 41.5mm (1.63"), thickness 2.8mm (0.11")

Price: 0.60 (0.72 Including VAT at 20%)




People who bought this item also bought:
1. Washer Shock Absorber Bush (Ref: RYF500160)
2. Washer - Shock Absorber Fixing (Ref: 243022A)
3. Flange Gasket (Ref: 231505=)
Key Washer for Hub Bearing
Lock Nut for Hub Bearing Ref: FRC8700D
Application: Series 1, Series 2, Series 3, Range Rover Classic, Discovery 1 and Defender.
Description: Lock nut for hub bearings. Used with second lock nut and locking washer.
Approximate dimensions: 52mm (2 1/16") across flats, thickness 8.5mm (0.33").
Original part number: 217355

Price: 0.85 (1.02 Including VAT at 20%)



Lock Nut for Hub Bearing
Flange Gasket Ref: 231505=
Application: Series 1, 2 & £.
Description: Paper gasket for drive flange to wheel hub.
Approximate dimensions: outside diameter 112mm (4.4"), inside diameter 77mm (3")

Price: 0.20 (0.24 Including VAT at 20%)




People who bought this item also bought:
1. Locker for Hub Nuts (Ref: 217353=)
2. Washer Shock Absorber Bush (Ref: RYF500160)
3. Gasket Water Pump S1 (Ref: 9118)
Flange Gasket
Drive Flange 10 Spline Ref: 571235
Application: Series 1 and Series 2 - all models. Series 3 short wheel base models to mid 1980.

Description: Original equipment specification 10 spline drive flange.

Approximate dimensions: Overall diameter 11.4cm(4.5"), height 50mm(2").

Old part number 217378.

Price: 16.00 (19.20 Including VAT at 20%)



Drive Flange 10 Spline
Replacement Drive Flange 10 Spline Ref: 571235D
Application: Series 1 and Series 2 - all models. Series 3 short wheel base models to mid 1980.

Description: Replacement 10 spline drive flange.

Approximate dimensions: Overall diameter 11.4cm(4.5"), height 50mm(2").

Old part number 217378.

Price: 8.50 (10.20 Including VAT at 20%)



Replacement Drive Flange 10 Spline
Cap for Hub Flange Ref: 219098
Application: Series 1, Series 2 and Series 3.
Description: Replacement protection cap for half shaft nut. Finish may be either shiney or dull plating as stock varies.

Price: 0.95 (1.14 Including VAT at 20%)




People who bought this item also bought:
1. Locker for Stub Axle (Ref: 277311D)
2. Locker Swivel Pin Retaining Nuts 3/8" diameter (Ref: 270287)
3. Universal Joint for Front Half-Shafts (Ref: RTC3690)
Cap for Hub Flange
Bolt for Hub Flange Ref: 215331
Application: Series 1, Series 2 and Series 3.
Description: Bolt for fixing half shaft drive flange to wheel hub. Six used per hub. Bolt is 3/8" BSF by 1 5/8" long

Price: 0.55 (0.66 Including VAT at 20%)



Bolt for Hub Flange
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Axles and Transmission Parts
Page:   <<   <  6  7

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Lever Arm for 4WD Select

Lever Arm for 4WD Select

15.80

Application: Series 1 to 1955.

Description: Lever arm with bronze bush to middle hole for selection of four wheel drive in high ratio.

Approximate dimensions: Overall length 116mm(4.6"), width 15.5mm(0.61"), thickness 6mm(0.24"), distance from centre of bushed hole to centre of slotted hole 36mm(1.42"), distance from centre of bushed hole to other hole is 68mm(2.67")

find out more

Olive for Vacuum Pipe

Olive for Vacuum Pipe

0.84

Application: Series 1 and Series2 with Solex 32PBI carburettor.

Description: Brass olive for use with 1/8" copper pipe.

Approximate dimensions: Length 4.7mm(0.19"), outside diameter 4.7mm(0.19"), internal dimater 1/8"(3.2mm).

find out more

Male Union for Vacuum Pipe

Male Union for Vacuum Pipe

2.40

Application: Series 1 and Series 2A.

Description: Brass male union for 1/8" copper pipe. Threaded to fit Solex 32PBI.

Aproximate dimensions: Length 10mm(0.39"), internal diameter 1/8"(3.2mm), hex 9mm(0.35") across flats, thread 1/4"BSF.

find out more

Grommet for vacuum pipe

Grommet for vacuum pipe

3.83

Application: Series 1 and Series 2A.

Description: Split rubber grommet for us with 214228 retaining clip. Used on 1/8" diameter copper vacuum pipe.

Approximate dimensions: Length 17mm(0.67"), internal diameter 3mm(1/8"), overall diameter 9mm(0.35")

find out more

Retaining Clip for Vacuum Pipe

Retaining Clip for Vacuum Pipe

2.78

Application: Series 1 and Series 2A.

Description: Retaining clip for copper vacuum pipe for advance and retard.

Approximate dimensions: 41.5mm(1.6") x 13mm(0.5") x 9mm(0.35"). Mounting hole 7mm(0.28")

find out more

Installer Oil Seal

Installer Oil Seal

33.79

Application: Evoque and Freelander 2.

Description: Installer for bellhousing differential oil seal. Use with 307-520.

Approximate dimensions: Overall diameter 80mm(3.15"), inside diameter 54mm(2.13"), height 48.5mm(1.9").

find out more

Installer Oilseal

Installer Oilseal

155.89

Application: Evoque and Freelander 2.

Description: Installer for quillshaft oil seal. Use with 307-520.

Approximate dimensions: Overall diameter 80mm(3.15"), height 64mm(2.52").


find out more

Pinion Bearing for Salisbury Differential

Pinion Bearing for Salisbury Differential

12.37

Application: Series 3 Long Wheel Base and Defender 110 models with rear Salisbury axle.

Descrtiption: Timken/Japanese sourced outer pinion taper roller bearing for Salisbury differentials.

Approximate dimensions: Outside diameter 2.85"(72.3mm), inside diameter 1 3/8"(34.9mm), depth 26.7mm(1.05")

Bearing numbers: HM88649/ HM88610

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -