Grommet - Brake Pipe Support
£0.31
Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more
Clip for brake pipe grommet
£0.61
Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more
Sealing Ring Water Pump to Cylinder Head
£2.18
Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more
Gasket Set for Series Gearboxes
£4.20
Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more
Water Pump Series1 Petrol
£51.00
Application: Series 1 1.6ltr & 2.0ltr petrol (gasolene) engines.
Description: Reproduction cast iron water pump, supplied with gaskets.
find out more
Gaiter for High/Low Gear Lever
£2.46
Application: Series 1, Series 2/2A and Series 3.
Description: Reproduction rubber gaiter for the high/low gear lever.
Approximate dimensions: Overall length 143mm, height 90mm.
find out more
Oil Seal Set for Gearbox
£13.70
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more
Copper Ring Water Pump to Thermostat Housing
£7.44
Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more
Wheel Stud for Series 1
£5.82
Application: All Series One models.
Description: Reproduction wheel stud for Series 1. Threaded 9/16"BSF. Use with nut 217361.
Approximate dimensions: Overall length 52mm(2"), short threaded end 12mm(0.47"), long threaded end 27.5mm(1.08"), land 12.5mm(0.5")
find out more
These Superb Prices are ONLY available when you order ON-LINE
Haven't found what you want? Then try our quotation service.
Steering Arm - Series 1
£17.82
Application: Series 1 models 1948 to 1956 approx.
Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.
Approximate dimensions: Overall length 17.4cm(6.9")
find out more
'D' Washer - Pedal Shaft
£0.96
Application: Series 1 models.
Description: 'D' washer for support shaft for brake and clutch pedals.
Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").
find out more
Fixing Kit for Manifolds - Metric
£12.83
Application: Series 3 from 1980 with 2.25 litre petrol engine.
Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers
find out more
Fixing Kit for Manifolds - Imperial
£10.20
Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.
Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers
find out more
Shackle Plate Rear
£11.16
Application: Series1 1948 to 1953.
Description: Shackle plate for rear springs with plain 9/16" diameter holes.
Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more
Shackle Plate Rear
£13.02
Application: Series 1 1948 to 1953.
Description: Shackle plate for rear springs with 1/2"BSF threaded holes.
Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more
Clip for 3/16" Brake Pipe
£1.39
Application: Series1, Series2/2A and Series3 models.
Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.
Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").
find out more
Rear End-plate for Cylinder Head
£97.66
Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.
Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.
Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")
find out more
Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain
Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England) email: sales@dingocroft.co.uk
Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -