Digital Dispensary

Product Sections


Best Sellers

Stud for Exhaust Manifold

Stud for Exhaust Manifold

2.36

Application: Series 1 1.6 and 2.0 litre, Series 2 2 litre.

Description: Stud to hold downpipe to exhaust manifold.

Approximate dimesions: 5/16"BSF threads to both ends, overall length 1.25"(32mm)

find out more

Brass Nut 5/16"BSF

Brass Nut 5/16

1.86

Application: Series1 exhaust manifold.

Description: Brass nut 5/16"BSF for holding downpipe to exhaust manifold.

Approximate dimensions: 3/8"(9.5mm) high, 17/32"(13.5mm) across flats.

find out more

Retaining Clip for Vacuum Pipe

Retaining Clip for Vacuum Pipe

2.78

Application: Series 1 and Series 2A.

Description: Retaining clip for copper vacuum pipe for advance and retard.

Approximate dimensions: 41.5mm(1.6") x 13mm(0.5") x 9mm(0.35"). Mounting hole 7mm(0.28")

find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Reproduction Solex 32PBI-2 Carburrettor

Reproduction Solex 32PBI-2 Carburrettor

148.78

Application: Series 1 and Series 2 with 2 litre petrol (gasolene) engine. 1954 to 1960 approx.

Description: Reproduction Solex 32PBI-2 carburrettor.

Back in stock.



find out more

Pinion Flange Remover-Replacer

Pinion Flange Remover-Replacer

172.76

Application:Freelander 2, 2006 onwards.
Description: Two part tool for removing and replacing pinion drive flange on rear differential.
Approximate dimensions: Inner tool - 160mm( 6.3") long, 3/4"(19mm) socket drive, fine spline(24) 24mm(0.95") overall diameter. Outer tool - 150mm(5.9") long, with 135mm(5.3") reaction arm. double hex(12point) socket 41mmAF
find out more

Front Side Lamp - Wipac

Front Side Lamp - Wipac

4.86

Application: Series 3 and Defender to 1994.

Description: Wipac branded lamp with clear lens. No bulb included. Wires, one black and one red.

Approximate dimensions: Lens diameter 67.5mm(2.7"), cable length 91cm(3').

find out more

Grommet for vacuum pipe

Grommet for vacuum pipe

4.37

Application: Series 1 and Series 2A.

Description: Split rubber grommet for us with 214228 retaining clip. Used on 1/8" diameter copper vacuum pipe.

Approximate dimensions: Length 17mm(0.67"), internal diameter 3mm(1/8"), overall diameter 9mm(0.35")

find out more

Nut and Bolt Kit for Propshafts

Nut and Bolt Kit for Propshafts

2.40

Application: Series 1, Series 2, Series 2A, Series 3 Land Rovers. All Defenders, Classic Range Rover, Range Rover 2 (38A), Discovery 1 and Discovery 2.

Description: Set of four 3/8UNF x 1.125" long bolts plus four short nyloc nuts.
find out more

These Superb Prices are ONLY available when you order ON-LINE

 Please complete the details below and then press Send

 Name: *
 Subject: *
 Email Address: *
 Message: *
  
  
  * denotes required fields highlighted.

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Bearin set for Layshaft

Bearin set for Layshaft

66.96

Application: Fairey overdrive as fitted to LT76 gearbox of Series1, Series2A and Series3 models.

Description: Set of 3 needle bearing caged assemblies.

Approximate dimensions of each bearing:Length 30mm(1.2"), overall dimeter 35.3mm(1.4"), internal dimater 31mm(1.2").

find out more

Side Lamp

Side Lamp

109.74

Application: Series 1 1948 to 1951.

Description: Reproduction bulkhead mounting side lamp.

Approximate dimensions: Overall diameter 46.4mm(1.8"), overall length including bulb holder 66mm(2.6").

find out more

Mounting Bush for Fuel Pump

Mounting Bush for Fuel Pump

3.68

Application: SU fuel pumps on Series1 and early Series2 models.

Description: Rubber mounting bush for SU electric fuel pump.

Approximate dimensions: Overall diameter 25mm(1"), internal diameter 7mm (0.28"), depth 12.5mm(0.5")

find out more

Mounting Pad for Fuel Pump

Mounting Pad for Fuel Pump

9.58

Application: SU fuel pumps on Series1 and early Series2 models.

Description: Rubber mounting pad for SU electric fuel pump.

Approximate dimensions: 83mm x 60mm x 6mm(3.3" x 2.4" x 0.25")

find out more

Hub Support

Hub Support

372.84

Application: Freelander 2 and Evoqur.

Description: Support for hub to aid removal of bearing using press.

Approximate dimensions: Overall diameter 20.5cm(8.1"), height 16.2cm(6.4")

find out more

Spring - Brake Light Switch

Spring - Brake Light Switch

6.52

Application: Series 1 1954 to 1958.

Description: Reproduction spring for activating the brake light switch.

Approximate dimesions: Overall length 13.5cm(5.3"), overall diameter 10mm(3/8")

find out more

Washer - Shocker Retention

Washer - Shocker Retention

0.50

Application: Series 1 1948 to 1953.

Description: Washer for retaining shock absorbers onto their mounts.

Approximate dimensions: Outside diameter 1.25"(32mm), inner diameter 7/16"(11mm), thickness 1/8"(3mm).

Old part number: 217245
find out more

Push Rod - Master Cylinder

Push Rod - Master Cylinder

22.32

Application: Series 1 1954 to 1958 with 10" drums.

Description: Reproduction pushrod for brake master cylinder. With 3/8"UNF thread and kexagonal collar.

Approximate dimesions: overall length 12.1cm(4.76")



find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -