Digital Dispensary

Product Sections


Best Sellers

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Gasket Exhaust Manifold to Down Pipe

Gasket Exhaust Manifold to Down Pipe

0.96

Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.
find out more

Split Pin - Shocker Retention

Split Pin - Shocker Retention

0.25

Application: Series 1, Series 2 and Series 3.

Description: Replacement split pin for retaining shock absorber to bottom plate of spring.

Approximate dimensions: Overall length 55.5mm(2.2"), diameter 6mm(0.24")

find out more

Gasket Cylinder Head End Plates

Gasket Cylinder Head End Plates

3.58

Application: Series 1 1.6ltr & 2.0ltr petrol (gasolene) engines.
Description: Original cork gasket for cylinder head end plates.
find out more

Rear Shock Absorber

Rear Shock Absorber

18.74

Application: Series 1 1954 onwards, Series 2 and 3 short wheel base models.
Description: Replacement rear shock absorber by Armstrong.
Approximate dimensions: Overall length closed 36.2cm(14.3"), overall length open 55.5cm(21.9").
Original part number 501445
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Speedo Drive Cable

Speedo Drive Cable

9.60

Application: Series One, Series 2 and 2A.
Description: Speedo cable assembly incorporating both inner and ouiter cables.
Approximate dimensions: Overall length 73"(85cm)
Original part numbers: 234536 & 234537, 270717 and 270718.
find out more

Rubber Peg for Wiper Blade

Rubber Peg for Wiper Blade

0.95

Application: Series 1 1948 to 1958.

Decription: Rubber peg for retaining wiper blade to wiper arm.

Approximate dimensions: overall length 20.5mm(0.8")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > DEFENDER Parts
Defender Books and Publications.Defender Books and Publications.
Manuals and parts books for Defender models.
Defender Engine PartsDefender Engine Parts
The Defender has been fitted with an enormous range of engines from the factory and even more by enterprising souls. The most common ones are; 2.25 and 2.5 4 cylinder petrol, 3.5 and 3.9 V8 petrol, 2.25 and 2.5 naturally aspirated diesels, 2.5 turbo diesel. 200TDi, 300TDi, td5, Puma diesel 2.4 and 2.2. Here follow sections for most of these.
Defender Brake PartsDefender Brake Parts
Up until 1993 Defenders were fitted with rear drum brakes. From 1994 disc brakes were fitted front and rear with vented discs fitted to the front of some models.
Defender Clutch PartsDefender Clutch Parts
Defender clutch covers, discs, release bearings, hydraulics etc
Defender Cooling SystemDefender Cooling System
Defender cooling system parts - hoses, radiators, thermostats, water pumps etc.
Defender DrivelineDefender Driveline
Parts for axles, hubs, propshafts etc
Defender Electrical PartsDefender Electrical Parts
All things electrical.
Defender Filtration SystemsDefender Filtration Systems
Filter kits and individual filters.
Defender Fuel SystemDefender Fuel System
Carburettors, pumps, fuel tanks, senders, injectors etc.
Defender Gearbox ComponentsDefender Gearbox Components
Defender has used a vast range of gearboxes and a smaller choice of transfer boxes. E£arly 4 cylinder models used the LT77 and then the R380. After 2007 the MT82 six speed box. Early v8s used the LT95 four speed box, then the LT85 five speed box, LT77 and finally the R380. Plus of course of ZF five speed automatic on the 50th aniversary v8.
Defender Steering PartsDefender Steering Parts
Steering components for Dwfender models
Defender Suspension PartsDefender Suspension Parts
Shock absorbers, suspension bushes, etc
Defender Interior TrimDefender Interior Trim
Clips, gaiters and bits like that!
Digital Dispensary > DEFENDER Parts

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -