Digital Dispensary

Product Sections


Best Sellers

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Male Union for Vacuum Pipe

Male Union for Vacuum Pipe

3.25

Application: Series 1 and Series 2A.

Description: Brass male union for 1/8" copper pipe. Threaded to fit Solex 32PBI.

Aproximate dimensions: Length 10mm(0.39"), internal diameter 1/8"(3.2mm), hex 9mm(0.35") across flats, thread 1/4"BSF.

find out more

Sump Gasket Series 1

Sump Gasket Series 1

10.82

Application: Series 1 1600cc or 2000cc petrol (gasolene) engine.
Description: Original cork sump gasket, manufactured in the 1950's.
find out more

'O' Ring for Thermostat

'O' Ring for Thermostat

0.55

Application: Series 1, 2 & 3 4cylinder engines.
Description: 'O' ring for sealing thermostat to cylinder head.
Approximate dimensions: outside diameter 55mm (2.2").
Original part number 01645
find out more

Swivel Housing Outer Seal

Swivel Housing Outer Seal

13.78

Application: Series 1, 2 & 3 front axles.
Description: Genuine oil seal for swivel housings.
Approximate dimensions: Outside diameter 16.8cm (6.6"), thickness 14.7mm (0.58")
Original part number: 502406.
find out more

Grommet for vacuum pipe

Grommet for vacuum pipe

4.37

Application: Series 1 and Series 2A.

Description: Split rubber grommet for us with 214228 retaining clip. Used on 1/8" diameter copper vacuum pipe.

Approximate dimensions: Length 17mm(0.67"), internal diameter 3mm(1/8"), overall diameter 9mm(0.35")

find out more

Set of Rivets for Bonnet Strip

Set of Rivets for Bonnet Strip

10.22

Application: Series 1 and early Series 2A.

Description: Set of 12 bifurcated rivets in black for retaining the bonnet rest strip 300824A.

Approximate dimensions: Head diameter 9.5mm(3/8"), length 14mm(9/16"), shank diameter 4.8mm(3/16").

find out more

Series1, 2 & 3 Wheel Bearing Kit with Japanese Bearings

Series1,  2 & 3 Wheel Bearing Kit with Japanese Bearings

39.94

Application: Series 1 front axle only, Series 2, Series 2A and Series 3 to 1980. Where inner bearing is larger than outer bearing. Covers both long and short wheel base vehicles, suitable for either front or rear wheel.

Description: Kit of parts to service one wheel hub. Kit comprises inner and outer Japanese manufactured wheel bearings (NTN or similar brand), Gaco inner seal, flange gasket, hub nut locker, felt outer seal, 'o' ring outer seal and split pin.

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Axles and Transmission Parts
Page:   <<   <  1  2  3  4  5  ...   >   >>
Shim for Outer Bearing of Diff Pinion, 0.010" Ref: 219549
Application: Series 1 and Series 2 differentials.

Description: 0.010" shim for setting position of differntial pinion and bearing pre-load.

Approximate dimensions: outside diameter 41mm (1.6"), inside diameter 32.5mm (1.28").

Price: 0.75 (0.90 Including VAT at 20%)



Shim for Outer Bearing of Diff Pinion, 0.010
Shim for Outer Bearing of Diff Pinion, 0.020" Ref: 233677
Application: Series 1 and Series 2 differentials.

Description: 0.020" thick shim for setting position of differntial pinion and bearing pre-load.

Approximate dimensions: outside diameter 41mm (1.6"), inside diameter 32.5mm (1.28").

Price: 3.12 (3.74 Including VAT at 20%)



Shim for Outer Bearing of Diff Pinion, 0.020
Filler Plug - Differential Housing Ref: 533358
Application: Series 1, Series 2 and Series 2A to vehicle suffix 'G'.

Description: Brass filler plug for differential housing.

Approximate dimensions: Height 28mm(1.1"), thread diameter 26mm(1.02"), overall diameter 36mm(1.4"), head 19mm(3/4") across flats.

Old part number: 05366


Price: 12.12 (14.54 Including VAT at 20%)




People who bought this item also bought:
1. Sealing Ring Water Pump to Cylinder Head (Ref: RTC1975)
2. Gasket Water Pump S1 (Ref: 9118)
3. Washer for Drain Plug (Ref: 515599)
Filler Plug - Differential Housing
Nut and Bolt Kit for Propshafts Ref: PROPFIX01
Application: Series 1, Series 2, Series 2A, Series 3 Land Rovers. All Defenders, Classic Range Rover, Range Rover 2 (38A), Discovery 1 and Discovery 2.

Description: Set of four 3/8UNF x 1.125" long bolts plus four short nyloc nuts.

Price: 2.00 (2.40 Including VAT at 20%)




People who bought this item also bought:
1. Male Union for Vacuum Pipe (Ref: 260707)
2. Olive for Fuel Pipe - 5/16" (Ref: 3136)
3. Return Spring - Iinjector Pump (Ref: 277502)
Nut and Bolt Kit for Propshafts
Replacement Universal Joint Kit Ref: RTC3291=
Application: Series 1 and Series 2/2A to approximately 1964.
Description: Universal joint repair kit including 4 circlips and a grease nipple.
Approximate Dimensions: Distance across faces of joint 75mm (2.95"), cap diameter 27mm (1.06"), cap length including seal 17mm ( 0.67").
Original part number 43023.

Price: 9.94 (11.93 Including VAT at 20%)




People who bought this item also bought:
1. Sender Unit - Fuel Tank (Ref: 236017D)
2. Bypass Hose Series 1 1948-1953 (Ref: 212345)
3. Headlamp Rim 7" (Ref: 274379)


Related products:
1. Nut and Bolt Kit for Propshafts (Ref: PROPFIX01)
Replacement Universal Joint Kit
Yoke for Propellor Shaft Ref: 262468
Application: Series 1 & 2.
Description: Yoke for propellor shaft. Only suitable for original prop shafts with the smaller universal joints - RTC3291.

Price: 20.00 (24.00 Including VAT at 20%)



Yoke for Propellor Shaft
Genuine Propshaft Gaiter Ref: 276484
Application: Series 1, Series 2/2A, Series 3, early 90/110, Classic Range Rover.

Description: Genuine gaiter and 2 clips for sliding joint on front and rear propellor shafts.

Price: 25.81 (30.97 Including VAT at 20%)



Genuine Propshaft Gaiter
Replacement Propshaft Gaiter Kit Ref: 276484D
Application: Series 1, Series 2/2A, Series 3, early 90/110, Classic Range Rover.

Description: Replacement gaiter and 2 clips for sliding joint on front and rear propellor shafts.

Price: 3.00 (3.60 Including VAT at 20%)




People who bought this item also bought:
1. Felt Seal Stub Shaft to Drive Flange (Ref: RTC3515)
2. Inner Wheel Hub Seal (Ref: RTC3510)
3. Nut and Bolt Kit for Propshafts (Ref: PROPFIX01)
Replacement Propshaft Gaiter Kit
Drain Plug - Axle Casing Ref: 235592
Application: Series 1 & 2.
Description: Solid brass drain plug.
Approximate dimensions: outside diameter 34.8mm (1.37"), hight 17.7mm (0.7").

Price: 6.95 (8.34 Including VAT at 20%)




People who bought this item also bought:
1. Universal Joint for Front Half-Shafts (Ref: RTC3690)
2. Replacement Universal Joint Kit (Ref: RTC3291=)
3. Replacement Swivel Housing S1, S2a & S3 (Ref: 539741D)


Related products:
1. Washer for Drain Plug (Ref: 515599)
Drain Plug - Axle Casing
Washer for Drain Plug Ref: 515599
Application: Series 1 & 2.
Description: Copper crush washer for axle drain plug.
Approximate dimensions: outside diameter 35mm (1.4").
Origilal part number 230509.

Price: 0.74 (0.89 Including VAT at 20%)




People who bought this item also bought:
1. Filler Plug - Differential Housing (Ref: 533358)
2. Spring 4WD Selector Shaft (Ref: 233449)
3. Drain Plug - Axle Casing (Ref: 235592)
Washer for Drain Plug
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Axles and Transmission Parts
Page:   <<   <  1  2  3  4  5  ...   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -