Digital Dispensary

Product Sections


Best Sellers

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Male Union for Vacuum Pipe

Male Union for Vacuum Pipe

3.25

Application: Series 1 and Series 2A.

Description: Brass male union for 1/8" copper pipe. Threaded to fit Solex 32PBI.

Aproximate dimensions: Length 10mm(0.39"), internal diameter 1/8"(3.2mm), hex 9mm(0.35") across flats, thread 1/4"BSF.

find out more

Sump Gasket Series 1

Sump Gasket Series 1

10.82

Application: Series 1 1600cc or 2000cc petrol (gasolene) engine.
Description: Original cork sump gasket, manufactured in the 1950's.
find out more

'O' Ring for Thermostat

'O' Ring for Thermostat

0.55

Application: Series 1, 2 & 3 4cylinder engines.
Description: 'O' ring for sealing thermostat to cylinder head.
Approximate dimensions: outside diameter 55mm (2.2").
Original part number 01645
find out more

Swivel Housing Outer Seal

Swivel Housing Outer Seal

13.78

Application: Series 1, 2 & 3 front axles.
Description: Genuine oil seal for swivel housings.
Approximate dimensions: Outside diameter 16.8cm (6.6"), thickness 14.7mm (0.58")
Original part number: 502406.
find out more

Grommet for vacuum pipe

Grommet for vacuum pipe

4.37

Application: Series 1 and Series 2A.

Description: Split rubber grommet for us with 214228 retaining clip. Used on 1/8" diameter copper vacuum pipe.

Approximate dimensions: Length 17mm(0.67"), internal diameter 3mm(1/8"), overall diameter 9mm(0.35")

find out more

Set of Rivets for Bonnet Strip

Set of Rivets for Bonnet Strip

10.22

Application: Series 1 and early Series 2A.

Description: Set of 12 bifurcated rivets in black for retaining the bonnet rest strip 300824A.

Approximate dimensions: Head diameter 9.5mm(3/8"), length 14mm(9/16"), shank diameter 4.8mm(3/16").

find out more

Series1, 2 & 3 Wheel Bearing Kit with Japanese Bearings

Series1,  2 & 3 Wheel Bearing Kit with Japanese Bearings

39.94

Application: Series 1 front axle only, Series 2, Series 2A and Series 3 to 1980. Where inner bearing is larger than outer bearing. Covers both long and short wheel base vehicles, suitable for either front or rear wheel.

Description: Kit of parts to service one wheel hub. Kit comprises inner and outer Japanese manufactured wheel bearings (NTN or similar brand), Gaco inner seal, flange gasket, hub nut locker, felt outer seal, 'o' ring outer seal and split pin.

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Brake Parts
Page:   <<   <  1  2  3  4  5  ...   >   >>
Bush, Clutch Pedal Lever Ref: 240838
Application: Series 1

Description: Reproduction bronze bush for clutch pedal lever and for left hand drive brake pedal lever.

Approximate dimensions: Overall length 29mm(1.14"), outside diameter 30mm( 1.18"), inside diameter 25.4mm(1").

Price: 13.03 (15.64 Including VAT at 20%)




People who bought this item also bought:
1. Spring - Brake Light Switch (Ref: 243225)
2. Shaft, Brake and Clutch Pedals (Ref: 240809)
3. Blanking Gommet for Bell Housing (Ref: 232604)
Bush, Clutch Pedal Lever
Bush for Relay Shaft Ref: 90218014
Application: Series1.

Description: Reproduction bronze bush for relay shaft of cluctch linkage on RHD models.

Approximate dimensions: Collar outside diameter 33.5mm(1.32"), body outer diameter 28.7mm(1.13"), internal diameter 24mm(0.95"), overall length 25mm(1").
Old part number: 218014


Price: 27.55 (33.06 Including VAT at 20%)



Bush for Relay Shaft
Grommet Series 1 Pedals Ref: 70620
Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.

Price: 9.00 (10.80 Including VAT at 20%)




People who bought this item also bought:
1. Gasket Oil Filter Housing to Block (Ref: ERR3607)
2. Yellow Knob - 4WD Gear lever (Ref: 232813)
3. 'O' Ring for Thermostat (Ref: 527235)
Grommet Series 1 Pedals
Felt Seal for Series 1 Pedals Ref: 70621
Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.

Price: 3.26 (3.91 Including VAT at 20%)




People who bought this item also bought:
1. Gasket Oil Filter Housing to Block (Ref: ERR3607)
2. Yellow Knob - 4WD Gear lever (Ref: 232813)
3. 'O' Ring for Thermostat (Ref: 527235)
Felt Seal for Series 1 Pedals
Brakelight Switch Ref: 7160
Application: Series One Land Rovers 1948 to 1958.

Description: Original style pull-on type of brakelight switch. Reproduced to original specification.

Approximate dimensions: Base 65x36mm(2.6"x 1.4"), overall height 39mm(1.54")

Price: 43.18 (51.82 Including VAT at 20%)




People who bought this item also bought:
1. Pair of Gearbox Mounts for Series 1 (Ref: S1GBOXMNTS)
2. Engine Mount Pair Series One 80" (Ref: S1ENGMNTS)
3. Pair of Electrical Sockets (Ref: CAB189)
Brakelight Switch
Spring - Brake Light Switch Ref: 243225
Application: Series 1 1954 to 1958.

Description: Reproduction spring for activating the brake light switch.

Approximate dimesions: Overall length 13.5cm(5.3"), overall diameter 10mm(3/8")

Price: 5.43 (6.52 Including VAT at 20%)




People who bought this item also bought:
1. Bush, Clutch Pedal Lever (Ref: 240838)
2. Shaft, Brake and Clutch Pedals (Ref: 240809)
3. Blanking Gommet for Bell Housing (Ref: 232604)
Spring - Brake Light Switch
Brakelight Switch Series 1 - replacement Ref: 7160D
Application: Series One Land Rovers 1948 to 1958.

Description: Replacement pull-on type of brakelight switch. Please note that this is not a direct replacement and requires a little fettling to use.

Approximate dimensions: Mounting hole centres 26mm (1")

Price: 5.31 (6.37 Including VAT at 20%)




People who bought this item also bought:
1. Wiper Blade (Ref: 261504)
2. Yellow Knob - 4WD Gear lever (Ref: 232813)
3. Tailpipe (Ref: 233931)
Brakelight Switch Series 1 - replacement
Clevis for Hand Brake Linkage Ref: 215809
Application: Series 1, 2 & 3.
Description: Reproduction clevis with pin for hand brake linkage. Threaded for 5/16"UNF rod.
Approximate dimensions: overall length 46mm (1.8")

Price: 3.05 (3.66 Including VAT at 20%)



Clevis for Hand Brake Linkage
80" Brake Pipe Set RHD Ref: ZZGB5600
Application: Series 1 80" vehicles Right Hand Drive.
Description: Set of 1/4" diameter brake pipes in copper with brass unions by Automec. Seven pipes are included in this set. Comes with plastic pipe clips. Reservoir to master cylinder pipe is not included.

Price: 117.04 (140.45 Including VAT at 20%)




People who bought this item also bought:
1. 5/16" diameter Copper Pipe - per inch (Ref: ZZHCP516)
2. 1/8" diameter Copper Pipe - per inch (Ref: ZZHCP018)
3. Nut for Fuel Pipe 5/16 (Ref: 50421)
80
1litre Bottle of Silicon Brake Fluid Ref: ZZDYNSILIDOT5
Application: All Landrover models.

Description: Dynolite's performance silicone Dot5 (dot 5) Brake Fluid repels moisture so, unlike standard polyglycol brake fluid, it never needs changing. Rust and corrosion are inhibited because moisture is kept out of the system and the high boiling point of 260 degrees C is maintained throughout the life of the product therefore ensuring consistent, safe performance. Thanks to this, Dynolite silicone brake fluid lasts the lifetime of your vehicle, never needing to be changed. It will also not damage your paintwork if spilled and will not easily catch fire in the event of an accident. Pure silicone brake fluid will essentially eliminate wear snd corrosion in the hydraulic system.
It is ideal for use in vehicles that are only used occasionally where otherwise water absorbtion into the brake fluid is a major problem.

Sorry, temporarily out of stock
.

Price: 25.96 (31.15 Including VAT at 20%)


1litre Bottle of Silicon Brake Fluid
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Brake Parts
Page:   <<   <  1  2  3  4  5  ...   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -