Digital Dispensary

Product Sections


Best Sellers

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Male Union for Vacuum Pipe

Male Union for Vacuum Pipe

3.25

Application: Series 1 and Series 2A.

Description: Brass male union for 1/8" copper pipe. Threaded to fit Solex 32PBI.

Aproximate dimensions: Length 10mm(0.39"), internal diameter 1/8"(3.2mm), hex 9mm(0.35") across flats, thread 1/4"BSF.

find out more

Sump Gasket Series 1

Sump Gasket Series 1

10.82

Application: Series 1 1600cc or 2000cc petrol (gasolene) engine.
Description: Original cork sump gasket, manufactured in the 1950's.
find out more

'O' Ring for Thermostat

'O' Ring for Thermostat

0.55

Application: Series 1, 2 & 3 4cylinder engines.
Description: 'O' ring for sealing thermostat to cylinder head.
Approximate dimensions: outside diameter 55mm (2.2").
Original part number 01645
find out more

Swivel Housing Outer Seal

Swivel Housing Outer Seal

13.78

Application: Series 1, 2 & 3 front axles.
Description: Genuine oil seal for swivel housings.
Approximate dimensions: Outside diameter 16.8cm (6.6"), thickness 14.7mm (0.58")
Original part number: 502406.
find out more

Grommet for vacuum pipe

Grommet for vacuum pipe

4.37

Application: Series 1 and Series 2A.

Description: Split rubber grommet for us with 214228 retaining clip. Used on 1/8" diameter copper vacuum pipe.

Approximate dimensions: Length 17mm(0.67"), internal diameter 3mm(1/8"), overall diameter 9mm(0.35")

find out more

Set of Rivets for Bonnet Strip

Set of Rivets for Bonnet Strip

10.22

Application: Series 1 and early Series 2A.

Description: Set of 12 bifurcated rivets in black for retaining the bonnet rest strip 300824A.

Approximate dimensions: Head diameter 9.5mm(3/8"), length 14mm(9/16"), shank diameter 4.8mm(3/16").

find out more

Series1, 2 & 3 Wheel Bearing Kit with Japanese Bearings

Series1,  2 & 3 Wheel Bearing Kit with Japanese Bearings

39.94

Application: Series 1 front axle only, Series 2, Series 2A and Series 3 to 1980. Where inner bearing is larger than outer bearing. Covers both long and short wheel base vehicles, suitable for either front or rear wheel.

Description: Kit of parts to service one wheel hub. Kit comprises inner and outer Japanese manufactured wheel bearings (NTN or similar brand), Gaco inner seal, flange gasket, hub nut locker, felt outer seal, 'o' ring outer seal and split pin.

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Brake Parts
Page:   <<   <  6
Brake Pipe Reservoir to Master Cylinder Ref: 230894
Application: Series 1 80" 1948 to 1953.

Description: 5/16" diameter copper brake pipe 17" long with 2 female unions. This is for right hand drive vehicles from chassis number 861001 onwards.

Price: 15.31 (18.37 Including VAT at 20%)



Brake Pipe Reservoir to Master Cylinder
'Trick' Pipe Reservoir to Master Cylinder Ref: 230894DD
Application: Series 1 80" models.

Description: This pipe allows the later brake reservoir 271581 to be used on 80" models. ( The original reservoir for this model is not currently available) It is 18"(45.7cm) long pipe in 1/4" diameter copper pipe with appropriate unions to fit the reservoir and the master cylinder.

NB. We can make this pipe up at different lengths to suit LHD models if required.

Price: 12.00 (14.40 Including VAT at 20%)




People who bought this item also bought:
1. 5/16" diameter Copper Pipe - per inch (Ref: ZZHCP516)
2. 1/8" diameter Copper Pipe - per inch (Ref: ZZHCP018)
3. 80" Brake Pipe Set RHD (Ref: ZZGB5600)
'Trick' Pipe Reservoir to Master Cylinder
80" Brake Pipe Set LHD Ref: ZZGL5600
Application: Series 1 80" vehicles Left Hand Drive.

Description: Set of 1/4" diameter brake pipes in kunifer (copper-nikel-iron alloy) with brass unions by Automec. Seven pipes NOT including reservoir to master cylinder. Comes with plastic pipe clips.

Price: 117.04 (140.45 Including VAT at 20%)




People who bought this item also bought:
1. Rotor Arm (Ref: 261242)
2. Gasket By-pass Hose Ends (Ref: 210419)
3. Yellow Knob - 4WD Gear lever (Ref: 232813)


Related products:
1. 1litre Bottle of Silicon Brake Fluid (Ref: ZZDYNSILIDOT5)
80
Brass 'T' Piece for 1/4" Pipes Ref: ZZHU34
Brass T peice threaded 7/16"UNF to take male connectors. Similar to 219827 T peice on Series 1 80" models.

Approximate dimensions: 34mm(1.3") x 35.4mm(1.4") x 16mm(0.625")

Price: 9.64 (11.57 Including VAT at 20%)



Brass 'T' Piece for 1/4
86/88" Brake Pipe Set RHD Ref: ZZGB5608
Application: Series 1 86" and 88" wheelbase models Right Hand Drive.

Description: Set of six 3/16" diameter brake pipes in copper with brass unions by Automec. Supplied with plastic pipe clips. Does not include reservoir to master cylinder pipe.

Price: 69.60 (83.52 Including VAT at 20%)



86/88
S1 86/88" Brake Pipe Set LHD Ref: ZZGL5608
Application: Series 1 86" and 88" wheelbase models Left Hand Drive.
Description: Set of six 3/16" diameter brake pipes in kunifer(copper-nickel-iron alloy) with brass unions by Automec. Supplied with plastic pipe clips. Does not include reservoir to master cylinder pipe.

NB Photograph is not of actual set, but all pipes look very similar coiled up!

Price: 66.00 (79.20 Including VAT at 20%)



S1 86/88
Grommet - Brake Pipe Support Ref: 6860L
Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")

Price: 0.26 (0.31 Including VAT at 20%)




People who bought this item also bought:
1. Clip for brake pipe grommet (Ref: 56666)
2. Brush Set for Dynamo (Ref: 261483)
3. Gasket Cover Plate to Timing Window (Ref: 50216)
Grommet - Brake Pipe Support
Clip for brake pipe grommet Ref: 56666
Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.

Price: 0.51 (0.61 Including VAT at 20%)




People who bought this item also bought:
1. Grommet - Brake Pipe Support (Ref: 6860L)
2. Sump Gasket Series 1 (Ref: 267780)
3. Gasket Cover Plate to Timing Window (Ref: 50216)
Clip for brake pipe grommet
Clip for 3/16" Brake Pipe Ref: 41379
Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

Price: 1.16 (1.39 Including VAT at 20%)




People who bought this item also bought:
1. Pack of 10 5/16" BSF Plain Nuts (Ref: 2828x10)
2. Gasket Exhaust Manifold to Down Pipe (Ref: 213358)
3. Stud for Exhaust Manifold (Ref: 213472)
Clip for 3/16
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Brake Parts
Page:   <<   <  6

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -