Digital Dispensary

Product Sections


Best Sellers

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gasket Set for Series Gearboxes

Gasket Set for Series Gearboxes

4.20

Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more

Water Pump Series1 Petrol

Water Pump Series1 Petrol

51.00

Application: Series 1 1.6ltr & 2.0ltr petrol (gasolene) engines.

Description: Reproduction cast iron water pump, supplied with gaskets.
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

13.70

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Wheel Stud for Series 1

Wheel Stud for Series 1

5.82

Application: All Series One models.

Description: Reproduction wheel stud for Series 1. Threaded 9/16"BSF. Use with nut 217361.

Approximate dimensions: Overall length 52mm(2"), short threaded end 12mm(0.47"), long threaded end 27.5mm(1.08"), land 12.5mm(0.5")

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Fuel System
Page:   <<   <  1  2  3  4  5   >   >>
Bracket - Accelerator Shaft Ref: 236998
Application: Series 1, Series 2 and Series 3.
Description: Support bracket for accelerator shafts.

Price: 1.50 (1.80 Including VAT at 20%)



Bracket - Accelerator Shaft
Bracket - Accelerator Shaft Ref: 236665
Application: Series 1, Series 2 and Series 3.
Description: Support bracket for accelerator shafts.

Price: 10.04 (12.05 Including VAT at 20%)



Bracket - Accelerator Shaft
Anchor Plate for Stop Spring Ref: 277565
Application: Series 1, Series 2 and Series 3 diesel models.
Description: Anchor plare for injection pump stop spring.
Approximate dimensions: overall length 30mm(1.2")

Price: 0.50 (0.60 Including VAT at 20%)



Anchor Plate for Stop Spring
Pin for Bell Crank on Injector Pump Ref: 277454
Application: Series 1 and Series 2 diesel.
Description: Pin for bell crank on head of injector pump for throttle linkage.
Approximate dimensions: overall length 40mm(1.6"), overall diameter 9.7mm(3/8"), thread 1/4" BSF.

Price: 3.16 (3.79 Including VAT at 20%)



Pin for Bell Crank on Injector Pump
Sender Unit - Fuel Tank Ref: 236017D
Application: Series 1 and Series 2/2A to suffix C inclusive.
Description: Reproduction moving coil type sender unit. This is a 'universal' unit and requires the float arm lengthening to work properly with the Land Rover fuel tank. Supplied with cork gasket.

Price: 81.22 (97.46 Including VAT at 20%)



Sender Unit - Fuel Tank
Fuel Pipe Ref: 218955
Application: Series 1 petrol models.

Description: Short fuel pipe from flexible pipe to carburettor. Reproduction pipe made with copper nickel alloy pipe shaped to fit.

Approximate dimensions: Overall lenghth 8"(20cm).

Price: 27.37 (32.84 Including VAT at 20%)




People who bought this item also bought:
1. Locker for Spring U Bolts (Ref: 234734)
2. Bolt for Banjo Connector - Solex 32PBI (Ref: 260167)
3. Banjo Connector for Solex 32PBI (Ref: 260166)
Fuel Pipe
Flexible Fuel Pipe Ref: 276267
Application: Series I models with petrol engines.

Description: Reproduction flexible fuel pipe with one male end and one female end. Runs from fuel pipe towards carburettor.

Approximate dimensions: Overall length 39cm(15.3")

Price: 27.90 (33.48 Including VAT at 20%)




People who bought this item also bought:
1. Seal Kit for Brake Master Cylinder (Ref: ZZSP1975-5)
2. Thermostat 82 degrees (Ref: 602687)
3. Brake Drum for 10" Brakes (Ref: 591661D)
Flexible Fuel Pipe
Nut - Fuel Pipe Ref: 2729
Application: Series 1 fuel pipes.

Description: Female brass nut 1/4"BSP thread with 3/8" diameter hole.

Approximate dimensions: Length 11mm(7/16"), 15.2mm(0.6") acrossflats.

Price: 2.70 (3.24 Including VAT at 20%)




People who bought this item also bought:
1. 5/16" diameter Copper Pipe - per inch (Ref: ZZHCP516)
2. Genuine Oil Filter Element RTC3183 (Ref: RTC3183)
3. Gasket Oil Filter Housing to Block (Ref: ERR3607)
Nut - Fuel Pipe
Nipple - Fuel pipe Ref: 2728
Application: Series 1 fuel pipes.

Description: Solder on nipple for 5/16" diameter copper fuel pipe. For use with 2729 union nut.

Apprximate dimensions: Length 13.7mm(0.54"),

Price: 2.93 (3.52 Including VAT at 20%)



Nipple - Fuel pipe
Olive for Fuel Pipe - 5/16" Ref: 3136
Application: Series 1 petrol models.

Description: brass olive for use with 5/16" diameter copper fuel pipe.

Approximate dimensions: Length 7.8mm(0.3"), outer diameter 10mm(0.4"), inner diameter 5/16"(8mm).

Price: 1.09 (1.31 Including VAT at 20%)




People who bought this item also bought:
1. 5/16" diameter Copper Pipe - per inch (Ref: ZZHCP516)
2. Genuine Oil Filter Element RTC3183 (Ref: RTC3183)
3. Gasket Oil Filter Housing to Block (Ref: ERR3607)
Olive for Fuel Pipe - 5/16
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Fuel System
Page:   <<   <  1  2  3  4  5   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -