Digital Dispensary

Product Sections


Best Sellers

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gasket Set for Series Gearboxes

Gasket Set for Series Gearboxes

4.20

Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more

Water Pump Series1 Petrol

Water Pump Series1 Petrol

51.00

Application: Series 1 1.6ltr & 2.0ltr petrol (gasolene) engines.

Description: Reproduction cast iron water pump, supplied with gaskets.
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

13.70

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Wheel Stud for Series 1

Wheel Stud for Series 1

5.82

Application: All Series One models.

Description: Reproduction wheel stud for Series 1. Threaded 9/16"BSF. Use with nut 217361.

Approximate dimensions: Overall length 52mm(2"), short threaded end 12mm(0.47"), long threaded end 27.5mm(1.08"), land 12.5mm(0.5")

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Fuel System
Page:   <<   <  1  2  3  4  5   >   >>
Electric Fuel Pump Series 1 - AUB79 Ref: AUB79
Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. SU part number AUA66. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Outlet has 'push on' connector and inlet threaded connector.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6
Back ln stock again!





Price: 114.25 (137.10 Including VAT at 20%)




People who bought this item also bought:
1. Reproduction Solex 32PBI-2 Carburrettor (Ref: 264664D)
2. Drain Tap for Radiator (Ref: 243237)
Electric Fuel Pump Series 1 - AUB79
SU Fuel Pump - Electronic Positive Earth Ref: AUA66EP
Application: Series 1 Land Rovers 1948 to 1958. Series 2 2litre.

Description: Authentic SU electric fuel pump with electronics instead points control, but otherwise to original pattern. SU part number AUA66EP. For mounting in engine bay. Positive earth vehicles only.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

Back in stock

Price: 124.00 (148.80 Including VAT at 20%)



SU Fuel Pump - Electronic Positive Earth
SU Fuel Pump - Electronic Negative Earth Ref: AUA66EN
Application: Series 1 Land Rovers 1948 to 1958. Series 2 2litre.

Description: Authentic SU electric fuel pump with electronics instead points control, but otherwise to original pattern. SU part number AUA66EN. For mounting in engine bay. Negative earth vehicles only.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

Price: 124.00 (148.80 Including VAT at 20%)



SU Fuel Pump - Electronic Negative Earth
Electric Fuel Pump - Series 1 Ref: AUA25
Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

Back in stock

Price: 114.25 (137.10 Including VAT at 20%)



Electric Fuel Pump - Series 1
SU Fuel Pump - Electronic Negative Earth Ref: AUA25EN
Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump with electronics instead points control, but otherwise to original pattern. For mounting in engine bay. For use on negative earth vehicles only. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

Price: 124.00 (148.80 Including VAT at 20%)



SU Fuel Pump - Electronic Negative Earth
SU Fuel Pump - Electronic Positive Earth Ref: AUA25EP
Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump with electronics instead points control, but otherwise to original pattern. For mounting in engine bay. For use on positive earth vehicles only. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

Price: 124.00 (148.80 Including VAT at 20%)



SU Fuel Pump - Electronic Positive Earth
Outlet Union for SU Fuel Pump Ref: 262294
Application: Series 1 petrol models.

Description: Outlet union threaded 1/4"BSP male. This can be fitted in place of the plain outlet spigot supplied with AUB79, AUA66EP and AUA66EN electric fuel pumps. Suits 2729 and 2728 connectors for use with 5/16" diameter copper fuel pipe.

Approximate dimensions: Length 20.6mm(0.81"), lower thread 22mm(0.87") diameter, hexagon is 18mm across flats.

Price: 10.00 (12.00 Including VAT at 20%)





Related products:
1. Nipple - Fuel pipe (Ref: 2728)
2. Nut - Fuel Pipe (Ref: 2729)
Outlet Union for SU Fuel Pump
Flow Stem 1/4" Ref: ABF252
Application: SU Fuel pumps.

Description: Flow stem to allow push-on connection for input on SU fuel pumps. Use with 2729 union nut.

Price: 2.65 (3.18 Including VAT at 20%)




People who bought this item also bought:
1. 5/16" diameter Copper Pipe - per inch (Ref: ZZHCP516)
2. Genuine Oil Filter Element RTC3183 (Ref: RTC3183)
3. Gasket Oil Filter Housing to Block (Ref: ERR3607)
Flow Stem 1/4
Elbow Connector for SU Pump Ref: 50499
Application: Series 1 models with petrol (gasolene) engines.

Description: Brass elbow with nut and olive for inlet union of SU electircal fuel pump.

Approximate dimensions: 21.7mm(0.85"0 x 28.5mm(1.12") x 13mm(0.5")

Price: 14.73 (17.68 Including VAT at 20%)




People who bought this item also bought:
1. Nut - Fuel Pipe (Ref: 2729)
2. Mounting Pad for Fuel Pump (Ref: 212557)
3. Mounting Bush for Fuel Pump (Ref: 212558)
Elbow Connector for SU Pump
Service Kit for AUA66 Series 1 Fuel Pump Ref: ZZEPK705
Service kit for modern Series 1 fuel pump AUA66 - see above.
This is NOT applicable for the original fuel pump - see ZZEPK700.

Price: 30.35 (36.42 Including VAT at 20%)



Service Kit for AUA66 Series 1 Fuel Pump
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Fuel System
Page:   <<   <  1  2  3  4  5   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -