Digital Dispensary

Product Sections


Best Sellers

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gasket Set for Series Gearboxes

Gasket Set for Series Gearboxes

4.20

Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more

Water Pump Series1 Petrol

Water Pump Series1 Petrol

51.00

Application: Series 1 1.6ltr & 2.0ltr petrol (gasolene) engines.

Description: Reproduction cast iron water pump, supplied with gaskets.
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

13.70

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Wheel Stud for Series 1

Wheel Stud for Series 1

5.82

Application: All Series One models.

Description: Reproduction wheel stud for Series 1. Threaded 9/16"BSF. Use with nut 217361.

Approximate dimensions: Overall length 52mm(2"), short threaded end 12mm(0.47"), long threaded end 27.5mm(1.08"), land 12.5mm(0.5")

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Fuel System
Page:  1  2  3  4  5   >   >>
Reproduction Solex 32PBI-2 Carburrettor Ref: 264664D
Application: Series 1 and Series 2 with 2 litre petrol (gasolene) engine. 1954 to 1960 approx.

Description: Reproduction Solex 32PBI-2 carburrettor.

Back in stock.



Price: 124.47 (149.36 Including VAT at 20%)




People who bought this item also bought:
1. Electric Fuel Pump Series 1 - AUB79 (Ref: AUB79)
2. Drain Tap for Radiator (Ref: 243237)
Reproduction Solex 32PBI-2 Carburrettor
Rebuild kit for Solex 32PBI-2 Carburettor Ref: 266693
Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor. Zenith part number ZRK17.
Description: A fairly comprehensive kit of parts to rebuild this carburettor.


Price: 62.93 (75.52 Including VAT at 20%)




People who bought this item also bought:
1. Lever Arm for Float 32PBI (Ref: 260753)
2. Olive for Vacuum Pipe (Ref: 260708)
3. Float for Solex 32PBI (Ref: 260745)
Rebuild kit for Solex 32PBI-2 Carburettor
Gasket Set for Solex 32PBI-2 Carburettor Ref: 274895
Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.

Description: Set of 6 gaskets and 8 fibre washers for this carburettor

Price: 8.37 (10.04 Including VAT at 20%)




People who bought this item also bought:
1. Diaphragm Kit for Solex 32PBI-2 (Ref: ZZB17453)
2. Genuine Oil Filter Element RTC3183 (Ref: RTC3183)
Gasket Set for Solex 32PBI-2 Carburettor
Diaphragm Kit for Solex 32PBI-2 Ref: ZZB17453
Application: Series 1 1600cc & 2.0ltr petrol (gasolene).

Description: Diaphragm kit for accelerator pump

Price: 14.41 (17.29 Including VAT at 20%)




People who bought this item also bought:
1. Gasket Set for Solex 32PBI-2 Carburettor (Ref: 274895)
2. Pack of 10 5/16" BSF Plain Nuts (Ref: 2828x10)
3. Rocker Cover Gasket (Ref: 267781)
Diaphragm Kit for Solex 32PBI-2
Float for Solex 32PBI Ref: 260745
Application: Series 1 1600cc & 2.0ltr petrol (gasolene).
Description: Brass float for this carburetor.

Price: 11.80 (14.16 Including VAT at 20%)




People who bought this item also bought:
1. Rebuild kit for Solex 32PBI-2 Carburettor (Ref: 266693)
2. Lever Arm for Float 32PBI (Ref: 260753)
3. Olive for Vacuum Pipe (Ref: 260708)
Float for Solex 32PBI
Lever Arm for Float 32PBI Ref: 260753
Application: Solex 32PBI carburrettor as fitted to Series 1.

Description: Toggle or lever arm for float.

Approximate dimensions: Overall length 24mm(0.95"), width 17mm(0.7").

Price: 2.17 (2.60 Including VAT at 20%)




People who bought this item also bought:
1. Diaphragm Kit for Solex 32PBI-2 (Ref: ZZB17453)
2. Pack of 10 5/16" BSF Plain Nuts (Ref: 2828x10)
3. Rocker Cover Gasket (Ref: 267781)
Lever Arm for Float 32PBI
Banjo Connector for Solex 32PBI Ref: 260166
Application: Series One.

Description: Reproduction brass fuel banjo to Solex carburetter.

Approximate dimensions: 1/42BSP male thread, 31mm(1.22") high, 19.6mm(0.77") deep.

Price: 14.98 (17.98 Including VAT at 20%)




People who bought this item also bought:
1. Bolt for Banjo Connector - Solex 32PBI (Ref: 260167)
2. Dip Switch - Floor Mounting (Ref: 232026)
3. Wiper Arm (Ref: 261503)
Banjo Connector for Solex 32PBI
Bolt for Banjo Connector - Solex 32PBI Ref: 260167
Application: Series One.

Description: Banjo bolt for use with 260166 banjo connector.

Approximate dimensions: Overall length 38mm(1.5"), head 17mm(0.67") across flats, shank diameter 12mm(0.47").

Price: 3.50 (4.20 Including VAT at 20%)




People who bought this item also bought:
1. Banjo Connector for Solex 32PBI (Ref: 260166)
2. Dip Switch - Floor Mounting (Ref: 232026)
3. Wiper Arm (Ref: 261503)


Related products:
1. Banjo Connector for Solex 32PBI (Ref: 260166)
Bolt for Banjo Connector - Solex 32PBI
Insulation Block for Solex 32PBI-2 Ref: 212232
Application: Series 1 with petrol engines.

Description: Thermal insulation block between carburettor and inlet manifold.

Approximate dimensions: length 78mm(3.1"), width 47.5mm(1.9"), thickness 6.7mm(0.26"), internal diameter 36.8mm(1.4").

Price: 4.01 (4.81 Including VAT at 20%)




People who bought this item also bought:
1. 'O' Ring for Thermostat (Ref: 527235)
2. Drain Tap for Radiator (Ref: 243237)
3. Wiper Blade (Ref: 261504)
Insulation Block for Solex 32PBI-2
Air Hose Series 1 Ref: 263149
Application: Series 1 with the 2 litre petrol engine from 1955 to 1958. Also Series 2 with the 2 litre engine.

Description: Reproduction air hose between air filter and carburettor.

Approximate dimensions: Overall length 24.5cm(9.6"), internal diameter 50.8mm(2").

Price: 58.00 (69.60 Including VAT at 20%)




People who bought this item also bought:
1. Genuine Oil Filter Element RTC3183 (Ref: RTC3183)
2. Pack of 10 5/16" BSF Plain Nuts (Ref: 2828x10)
3. Steering Arm - Series 1 (Ref: 242259)
Air Hose Series 1
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Fuel System
Page:  1  2  3  4  5   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -