Digital Dispensary

Product Sections


Best Sellers

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gasket Set for Series Gearboxes

Gasket Set for Series Gearboxes

4.20

Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more

Water Pump Series1 Petrol

Water Pump Series1 Petrol

51.00

Application: Series 1 1.6ltr & 2.0ltr petrol (gasolene) engines.

Description: Reproduction cast iron water pump, supplied with gaskets.
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

13.70

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Wheel Stud for Series 1

Wheel Stud for Series 1

5.82

Application: All Series One models.

Description: Reproduction wheel stud for Series 1. Threaded 9/16"BSF. Use with nut 217361.

Approximate dimensions: Overall length 52mm(2"), short threaded end 12mm(0.47"), long threaded end 27.5mm(1.08"), land 12.5mm(0.5")

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Suspension Parts
Page:   <<   <  1  2  3   >   >>
Rear Spring Dowel Bolt Ref: 243130
Application: Series 1 1954 to 1958, Series 2 & 3 short wheel base models.
Description: Centre bolt for rear spring. Holds spring together and locates spring to axle,
Approximate dimensions: Shank is 69mm(2.75") long with 38/" BSF thread on end, head is 5/8"(15.9mm) diameter and 3/8"(9.5mm) high.

Price: 0.90 (1.08 Including VAT at 20%)



Rear Spring Dowel Bolt
Second Leaf for Front Spring Ref: 243126
Application: Series 1 1954 to 1958, Series 2 & 3.
Description: 2nd leaf for front springs. Why replace the whole spring when just one leaf has broken?
Approximate dimensions: overal length 90cm(35"), width 6.4cm(2.5")

Price: 20.30 (24.36 Including VAT at 20%)



Second Leaf for Front Spring
'U' Bolt for Rear Spring Ref: 242127D
Application: Series 1 1954 - 1958, Series 2.
Description: Replacement U bolt for retaining rear spring to axle.
Approximate dimensions: Overall length 7 5/8" (19.4cm), centre to centre of legs 3 3/8" (8.6cm), 7/16" BSF thread, 1 7/8" (4.8cm) length of thread.

Price: 2.20 (2.64 Including VAT at 20%)




People who bought this item also bought:
1. Wheel Stud for Series 1 (Ref: 217360)
'U' Bolt for Rear Spring
Locker for Spring U Bolts Ref: 234734
Application: Series One 1952 to 1958, Series Two.
Description: Locker plate for road spring 'U' bolts. These are for the later 2.5" wide springs.
Approximate dimensions: Hole centre to hole centre 3 1/16"( 77.8mm), hole diameter 7/16" (11.5mm)

Price: 4.30 (5.16 Including VAT at 20%)




People who bought this item also bought:
1. Washer for Drain Plug (Ref: 515599)
2. Rotor Arm (Ref: 261242)
3. Replacement Distributor Cap Series One (Ref: 261240D)
Locker for Spring U Bolts
Locker for Spring U Bolts Ref: 217261
Application: Series One 1948 to 1951.
Description: Locker plare for road spring 'U' bolts. These are for the early narrow springs.
Approximate dimensions: Hole centre to hole centre 2 5/16" (59mm), hole diameter 7/16"(11.5mm)

Sorry, currently unavailable.

Price: 2.95 (3.54 Including VAT at 20%)


Locker for Spring U Bolts
Shock Absorber 1948 - 1953 Ref: 241037
Application: Series 1 1948 to 1953.
Description: Reproduction shock absorber suitable for both front and rear for use on 9/16" mounting bolts/pins. Supplied with 4 rubber bushes. Extended length 52cm(20.5"), closed length 33.7cm(13.3"), overall diameter 54mm(2.1").

Belatedly back in stock.

Price: 46.83 (56.20 Including VAT at 20%)




People who bought this item also bought:
1. Washer for Drain Plug (Ref: 515599)
2. Clip for 3/16" Brake Pipe (Ref: 41379)
3. Gasket Carburetter to Inlet Manifild (Ref: 212233)
Shock Absorber 1948 - 1953
Bush for Shock Absorber 1948 to 1953 Ref: 565395
Application: Series One 1948 to 1953.

Description: Rubber bush for early shock absorbers. 2 are fitted to each end of shock absorber.

Approximate dimensions: overall length 19mm(0.75"), outside diameter 30mm(1.2"), inside diameter 15.3mm(0.6")

Price: 1.38 (1.66 Including VAT at 20%)



Bush for Shock Absorber 1948 to 1953
Special Mounting Bolt Ref: 231784
Application: Series 1 80"

Description: Left hand rear shock absorber mounting bolt that doubles up as exhaust mount.

Approximate dimensions: Overall length 20.8cm(8.2"), 7/16"BSF thread, collar diameter 32mm(1.25")

Price: 13.27 (15.92 Including VAT at 20%)




People who bought this item also bought:
1. Wiper Arm (Ref: 261503)
2. Acorn for HT Leads (Ref: 214278)
3. Ignition and Lighting Switch (Ref: 217589)
Special Mounting Bolt
Washer - Shocker Retention Ref: KYF500070
Application: Series 1 1948 to 1953.

Description: Washer for retaining shock absorbers onto their mounts.

Approximate dimensions: Outside diameter 1.25"(32mm), inner diameter 7/16"(11mm), thickness 1/8"(3mm).

Old part number: 217245

Price: 0.42 (0.50 Including VAT at 20%)




People who bought this item also bought:
1. Grommet - Brake Pipe Support (Ref: 6860L)
2. Clip for brake pipe grommet (Ref: 56666)
Washer - Shocker Retention
Front Shock Absorber Ref: RTC4230D
Application: Series 1 1954 onwards, Series 2 and 3 short wheel base models.

Description: Replacement front shock absorber by Armstrong.

Approximate dimensions: Overall length closed 31.2cm(12.3"), overall length open 45.7cm(18").

Original part number 501444

Price: 15.62 (18.74 Including VAT at 20%)




People who bought this item also bought:
1. Washer for Drain Plug (Ref: 515599)
2. Vacuum Advance Pipe (Ref: 214231)
3. Wheel Stud for Series 1 (Ref: 217360)
Front Shock Absorber
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Suspension Parts
Page:   <<   <  1  2  3   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -