Digital Dispensary

Product Sections


Best Sellers

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Male Union for Vacuum Pipe

Male Union for Vacuum Pipe

3.25

Application: Series 1 and Series 2A.

Description: Brass male union for 1/8" copper pipe. Threaded to fit Solex 32PBI.

Aproximate dimensions: Length 10mm(0.39"), internal diameter 1/8"(3.2mm), hex 9mm(0.35") across flats, thread 1/4"BSF.

find out more

Sump Gasket Series 1

Sump Gasket Series 1

10.82

Application: Series 1 1600cc or 2000cc petrol (gasolene) engine.
Description: Original cork sump gasket, manufactured in the 1950's.
find out more

'O' Ring for Thermostat

'O' Ring for Thermostat

0.55

Application: Series 1, 2 & 3 4cylinder engines.
Description: 'O' ring for sealing thermostat to cylinder head.
Approximate dimensions: outside diameter 55mm (2.2").
Original part number 01645
find out more

Swivel Housing Outer Seal

Swivel Housing Outer Seal

13.78

Application: Series 1, 2 & 3 front axles.
Description: Genuine oil seal for swivel housings.
Approximate dimensions: Outside diameter 16.8cm (6.6"), thickness 14.7mm (0.58")
Original part number: 502406.
find out more

Grommet for vacuum pipe

Grommet for vacuum pipe

4.37

Application: Series 1 and Series 2A.

Description: Split rubber grommet for us with 214228 retaining clip. Used on 1/8" diameter copper vacuum pipe.

Approximate dimensions: Length 17mm(0.67"), internal diameter 3mm(1/8"), overall diameter 9mm(0.35")

find out more

Set of Rivets for Bonnet Strip

Set of Rivets for Bonnet Strip

10.22

Application: Series 1 and early Series 2A.

Description: Set of 12 bifurcated rivets in black for retaining the bonnet rest strip 300824A.

Approximate dimensions: Head diameter 9.5mm(3/8"), length 14mm(9/16"), shank diameter 4.8mm(3/16").

find out more

Series1, 2 & 3 Wheel Bearing Kit with Japanese Bearings

Series1,  2 & 3 Wheel Bearing Kit with Japanese Bearings

39.94

Application: Series 1 front axle only, Series 2, Series 2A and Series 3 to 1980. Where inner bearing is larger than outer bearing. Covers both long and short wheel base vehicles, suitable for either front or rear wheel.

Description: Kit of parts to service one wheel hub. Kit comprises inner and outer Japanese manufactured wheel bearings (NTN or similar brand), Gaco inner seal, flange gasket, hub nut locker, felt outer seal, 'o' ring outer seal and split pin.

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Engine Parts
Page:   <<   <  6  7
Exhaust Gasket Pair for Series1 petrol engines Ref: 9184PAIR
Application: Series 1 models fitted with either the 1.6 litre or 2.0 litre petrol (gasolene) engine.

Description: Pair of gaskets for jointing the exhaust manifold to cylinder head.

NB they may not be the aluminium faced material as per photo. We are between regular suppliers and are stocking what can be found!

Price: 9.40 (11.28 Including VAT at 20%)




People who bought this item also bought:
1. Gasket Side Cover (Ref: 267779)
2. Oil Seal between Crankshaft and Front Cover (Ref: ERR6490)
3. Gasket Inlet Manifold to Cylinder Head (Ref: 9179)
Exhaust Gasket Pair for Series1 petrol engines
Gasket Exhaust Manifold to Down Pipe Ref: 213358
Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.

Price: 0.80 (0.96 Including VAT at 20%)




People who bought this item also bought:
1. Gaiter for Main Gear Lever (Ref: 301437A)
2. Solid Aluminium Rivets - 1/2" long - bag of 50 (Ref: 300784X50)
3. Set of Rivets for Bonnet Strip (Ref: 68087x12)
Gasket Exhaust Manifold to Down Pipe
Stud for Exhaust Manifold Ref: 213472
Application: Series 1 1.6 and 2.0 litre, Series 2 2 litre.

Description: Stud to hold downpipe to exhaust manifold.

Approximate dimesions: 5/16"BSF threads to both ends, overall length 1.25"(32mm)

Price: 1.97 (2.36 Including VAT at 20%)




People who bought this item also bought:
1. Brush Set for Starter Motor (Ref: 260055)
2. Grommet for vacuum pipe (Ref: 214229)
3. Gaiter for Main Gear Lever (Ref: 301437A)
Stud for Exhaust Manifold
Brass Nut 5/16"BSF Ref: 3771
Application: Series1 exhaust manifold.

Description: Brass nut 5/16"BSF for holding downpipe to exhaust manifold.

Approximate dimensions: 3/8"(9.5mm) high, 17/32"(13.5mm) across flats.

Price: 1.55 (1.86 Including VAT at 20%)




People who bought this item also bought:
1. Stud for Exhaust Manifold (Ref: 213472)
2. Yellow Knob - 4WD Gear lever (Ref: 232813)
3. Gaiter for Hand Brake Lever (Ref: 303947)
Brass Nut 5/16
Exhaust Manifold Ref: 216548
Application: Series 1 with 1.6 litre petrol engine and early 2.0 litre to 1953.

Description: Reproduction cast iron exhaust manifold.

Price: 224.75 (269.70 Including VAT at 20%)





Related products:
1. Brass Nut 5/16"BSF (Ref: 3771)
2. Exhaust Gasket Pair for Series1 petrol engines (Ref: 9184PAIR)
3. Gasket Exhaust Manifold to Down Pipe (Ref: 213358)
Exhaust Manifold
Exhaust Manifold Ref: 237978
Application: Series 1 2.0ltr petrol (gasolene) engine.
Description: Reproduction exhaust manifold, supplied without studs.

Price: 224.75 (269.70 Including VAT at 20%)





Related products:
1. Brass Nut 5/16"BSF (Ref: 3771)
2. Exhaust Gasket Pair for Series1 petrol engines (Ref: 9184PAIR)
3. Gasket Exhaust Manifold to Down Pipe (Ref: 213358)
Exhaust Manifold
Inlet Manifold Ref: 218954
Application: Series 1 with 1.6 or 2.0 litre petrol (gasolene) engine.

Description: Inlet manifold in aluminium. Photograph shows bare aluminium, but some of these are supplied in light green pain finish. We have no control over finish supplied as this is now a rapidly diminishing supply.

Approximate dimensions: Overall length 35cm(13.8")

Price: 98.92 (118.70 Including VAT at 20%)



Inlet Manifold
Spigot Bush Ref: LFB500050
Application: All 4 and 6 cylinder engines fitted to Series 1, 2 & 3. Also 200 & 300TDi fitted to Defender, Discovery 1 and Range Rover Classic. Also TD5 models. In addition Series 1, 2 and 3 transfer box.

Description: Bronze bush fitted to rear of crankshaft to take nose of first motion shaft of gearbox. Also used as bush between front output shaft and rear output shaft in Series transfer boxes (not 109V8).
Original part number 8566 and 8566L.

Approximate dimensions: Outside diameter 1 1/16"(27mm), inside diameter 7/8"(22mm), length 0.84"(21.4mm)

Price: 1.21 (1.45 Including VAT at 20%)




People who bought this item also bought:
1. Yellow Knob - 4WD Gear lever (Ref: 232813)
2. Gasket By-pass Hose Ends (Ref: 210419)
3. Retainer and Fixings for Hi/Lo Gaiter (Ref: 303817KIT)
Spigot Bush
Gasket Cover Plate to Timing Window Ref: 50216
Application: S1, S2 & S3 4 cylinder engines.
Description: Cork gasket for cover plate on flywheel housing.

Price: 0.88 (1.06 Including VAT at 20%)




People who bought this item also bought:
1. Grommet - wiring (Ref: 3H822L)
2. Felt Seal for Series 1 Pedals (Ref: 70621)
3. Gasket By-pass Hose Ends (Ref: 210419)
Gasket Cover Plate to Timing Window
Engine Mount Pair Series One 80" Ref: S1ENGMNTS
Application: 80" wheelbase Series 1 1948 to 1953.

Description: Pair of mounts for engine block with mounting bolts 2&15/16" long.

Price: 89.90 (107.88 Including VAT at 20%)




People who bought this item also bought:
1. Brakelight Switch (Ref: 7160)
2. Axle Bump Rubber (Ref: 241380)
3. Water Pump Series1 Petrol (Ref: 269974)
Engine Mount Pair Series One 80
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Engine Parts
Page:   <<   <  6  7

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -