Digital Dispensary

Product Sections


Best Sellers

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gasket Set for Series Gearboxes

Gasket Set for Series Gearboxes

4.20

Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more

Water Pump Series1 Petrol

Water Pump Series1 Petrol

51.00

Application: Series 1 1.6ltr & 2.0ltr petrol (gasolene) engines.

Description: Reproduction cast iron water pump, supplied with gaskets.
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

13.70

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Wheel Stud for Series 1

Wheel Stud for Series 1

5.82

Application: All Series One models.

Description: Reproduction wheel stud for Series 1. Threaded 9/16"BSF. Use with nut 217361.

Approximate dimensions: Overall length 52mm(2"), short threaded end 12mm(0.47"), long threaded end 27.5mm(1.08"), land 12.5mm(0.5")

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Gearbox Parts
Page:   <<   <  6  7   >   >>
Block - Selector Shaft 4WD Ref: 233406
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Block on four wheel drive selector shaft.

Price: 3.25 (3.90 Including VAT at 20%)



Block - Selector Shaft 4WD
Spring 4WD Selector Shaft Ref: 233449
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Spring for four wheel drive selector shaft.
Approximate dimensions: free length 71mm (2.8"), overall diameter 21.5mm (0.85")

Price: 0.75 (0.90 Including VAT at 20%)



Spring 4WD Selector Shaft
Yellow Knob - 4WD Gear lever Ref: 232813
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Threaded gear knob for four wheel drive.

Price: 2.86 (3.43 Including VAT at 20%)




People who bought this item also bought:
1. Felt Seal for Series 1 Pedals (Ref: 70621)
2. Grommet Series 1 Pedals (Ref: 70620)
3. Gasket Water Branch to Cylinder Head (Ref: 210447)
Yellow Knob - 4WD Gear lever
Spring High/Low Selector Shaft Ref: 217445
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Spring on high/low selector shaft in transfer box.
Approximate dimensions: free length 186mm (7.3"), outside diameter 29mm ( 1.14")

Price: 3.10 (3.72 Including VAT at 20%)




People who bought this item also bought:
1. Oil Seal Set for Gearbox (Ref: 600603KIT)
2. Washer for Drain Plug (Ref: 515599)
3. Clip for brake pipe grommet (Ref: 56666)
Spring High/Low Selector Shaft
Plug - Retaining Plunger Ref: 233441
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Brass plug for retaining detent plunger on the high/low selector shaft.

Price: 0.85 (1.02 Including VAT at 20%)




People who bought this item also bought:
1. Steering Ball Joint, Right Hand Thread (Ref: 608464D)
2. Gasket Set for Series Gearboxes (Ref: 600603D)
3. Clamp Kit for Steering Rods (Ref: 577898KIT)
Plug - Retaining Plunger
Link Selector Shaft High/Low Ref: 238329
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Link selector shaft to high/low gear lever.

Price: 2.50 (3.00 Including VAT at 20%)




People who bought this item also bought:
1. Lever Assembly for 4WD Select (Ref: 268847)
2. Rear Output Drive Flange (Ref: 236630)
Link Selector Shaft High/Low
Red Knob High/Low Gear Lever Ref: 219521
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Threaded knob for the high/low selector lever.

Price: 2.47 (2.96 Including VAT at 20%)




People who bought this item also bought:
1. Replacement Distributor Cap Series One (Ref: 261240D)
2. Rotor Arm (Ref: 261242)
3. Exhaust Valve 1600cc (Ref: 234993)
Red Knob High/Low Gear Lever
Connector Gear Change to Pivot Shaft Ref: 538536
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Connector gear change to pivot shaft for four wheel drive.
Original part number 233436.

Price: 7.08 (8.50 Including VAT at 20%)



Connector Gear Change to Pivot Shaft
Lever Arm for 4WD Select Ref: 233414
Application: Series 1 to 1955.

Description: Lever arm with bronze bush to middle hole for selection of four wheel drive in high ratio.

Approximate dimensions: Overall length 116mm(4.6"), width 15.5mm(0.61"), thickness 6mm(0.24"), distance from centre of bushed hole to centre of slotted hole 36mm(1.42"), distance from centre of bushed hole to other hole is 68mm(2.67")

Price: 13.17 (15.80 Including VAT at 20%)



Lever Arm for 4WD Select
Lever Assembly for 4WD Select Ref: 268847
Application: Series 1 from 1956, Series 2 & Series 3 with 4 or 6 cylinder engine.

Description: Lever assembly four wheel drive select.

Approximate dimensions: overall length 114mm (4.5").

Price: 13.73 (16.48 Including VAT at 20%)




People who bought this item also bought:
1. Link Selector Shaft High/Low (Ref: 238329)
2. Rear Output Drive Flange (Ref: 236630)
Lever Assembly for 4WD Select
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Gearbox Parts
Page:   <<   <  6  7   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -