Digital Dispensary

Product Sections


Best Sellers

Gasket Set for Solex 32PBI-2 Carburettor

Gasket Set for Solex 32PBI-2 Carburettor

7.66

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.
Description: Set of 6 gaskets and 8 fibre washers for this carburettor
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Differential Pinion

Oil Seal Differential Pinion

5.21

Application: Series 1, 2 & 3 Rover type differentials.

Description: Oil seal to nose of differential. Corteco/Gaco boxed.

Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").

Original part number: 217507.
find out more

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Gasket for Differential to Axle Casing

Gasket for Differential to Axle Casing

0.60

Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Page:   <<   <  1  2  3  4  5  ...   >   >>
Holding Tool for Viscous Fan Ref: 303-1143
Application: Discovery3, Range Rover 3 and Range Rover Sport with TDV6 diesel.
Description: Holding tool for viscous fan hub, used in conjunction with 303-1142
Approximate dimensions: overall length 64.5cm (25.4")

Price: 57.45 (68.94 Including VAT at 20%)



Holding Tool for Viscous Fan
Remover Crankshaft Damper Ref: 303-1149
Application: Defender with Puma TDCi engine.

Description: Puller to remove crankshaft torsional vibration damper. Also used as base tool for other applications.

Approximate dimensions: Force screw - 224mm(8.8") long. Bolts M8 x 100mm. Beam 90mm(3.5") x 30mm(1.2") x 20mm(0.8")

Price: 84.77 (101.72 Including VAT at 20%)



Remover Crankshaft Damper
Locking Tool - Fuel Injection Pump Sprocket Ref: 303-1151
Application: Defender 2007 to 2016 with Puma TDCi engine.

Description: Tool to lock sprocket of injection pump in position.

Approximate dimensions: Overall diameter 115mm(4.5"), inside diameter 69mm(2.7"), height 22mm(0.9").

Price: 8.25 (9.90 Including VAT at 20%)



Locking Tool - Fuel Injection Pump Sprocket
Installer Crank Position Sensor Ref: 303-1237
Application: TDV8 engine in Range Rover L322 and Range Rover Sport.

Description: Installer for the crankshaft position sensor.

Approximate dimensions: Outside dsiameter 124mm(4.9")

Price: 187.02 (224.42 Including VAT at 20%)



Installer Crank Position Sensor
Timing Pin Crankshaft Ref: 303-1238
Application: Range Rover 3rd Generation (L322) with 3.6litre V8 diesel engine.
Description: Pin for locking crankshaft in correct position for valve timing.
Approximate dimensions: overall length 165mm(3.5")

Price: 21.71 (26.05 Including VAT at 20%)



Timing Pin Crankshaft
Camshaft Rotation Pin Ref: 303-1239
Application: Range Rover 3rd Generation (L322) with 3.6litre V8 diesel engine.
Description: Pin for rotating camshafts to correct position for valve timing.
Approximate dimensions: overall length 165mm (6.5")

Price: 24.35 (29.22 Including VAT at 20%)



Camshaft Rotation Pin
Oilseal Installer - Crankshaft rear Ref: 303-1271
Application: Freelander 2 and Evoque when fitted with 2.2 diesel engine.

Description: Tool for installing the oilseal to rear of crankshaft.

Approximate dimensions: Overall diameter 11cm(4.3"), height 10cm(3.9")

Price: 101.50 (121.80 Including VAT at 20%)



Oilseal Installer - Crankshaft rear
Locking Tool for Balance Shaft Ref: 303-1329
Application: Freelander 2 and Evoque when fitted with the 2.2litre diesel engine.

Description: Locking tool for the engine balance shaft.

Approximate dimensions: Main body 64mm(2.52") x 50mm(1.97") x 13mm(0.51")

Price: 56.11 (67.33 Including VAT at 20%)



Locking Tool for Balance Shaft
Backlash Lever - Balance Shaft Ref: 303-1330
Application: Freelander 2 vand Evoque when fitted with 2.2litre diesel.

Description: Backlash lever for the balance shaft of this engine.

Approximate dimensions: Overall length 18cm(7.1").

Price: 42.95 (51.54 Including VAT at 20%)



Backlash Lever - Balance Shaft
Forcing Screw and Bolts Ref: 303-1333
Application: Defender 2007 to 2010 with Puma TDCi engine.

Description: The forcing screw and bolts are used with tool 303-1149 to remove the fuel injection pump where the sprocket has M8 threaded holes.

Approximate dimensions: Forcing screw - overall length 61mm(2.4"), thread diameter 20mm(0.8"), head 24mm(0.95") across flats. Bolts - M8 x70mm.

Price: 28.93 (34.72 Including VAT at 20%)





Related products:
1. Remover Crankshaft Damper (Ref: 303-1149)
Forcing Screw and Bolts
Page:   <<   <  1  2  3  4  5  ...   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Outer Pinion Bearing

Outer Pinion Bearing

10.72

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for outer end of differential pinion gear. Timken bearing numbers HM88046/HM88010

Approximate dimensions: Outside diameter 2.7"(68.5mm), inside diameter 1.25"(31.8mm)., height 0.93"(23.5mm).


find out more

Inner Pinion Bearing - Differential

Inner Pinion Bearing - Differential

21.70

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for inner end of differential pinion gear. Timken bearing numbers HM801346X/HM801310

Approximate dimensions: Outside diameter 3.25"(82.5mm), inside diameter 1.5"(38mm)., height 1.22"(31mm).

find out more

Seal Kir for 1 1/8" Wheel Cylinders

Seal Kir for 1 1/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for rear wheel cylinders with bore of 1 1/8"(28.5mm). Kit has sufficient seals for both front wheel cylinders.

find out more

Seal Kit for 1 3/8" Wheel Cylinders

Seal Kit for 1 3/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for front wheel cyliders with bore of 1 3/8"(35mm). Kit has sufficient seals for both front wheel cylinders.


find out more

Outlet Nozzle - SU Fuel Pump

Outlet Nozzle - SU Fuel Pump

4.44

Application: Series 1 and early Series 2 models.

Description: Nozzle for outlet of SU fuel pumps. Allows push-on fuel hose connection to pump.

Approximate dimensions: Thread diameter 22mm(0.87"), nozzle diameter 7mm(0.28").

find out more

Wiper Arm Series 3 RH

Wiper Arm Series 3 RH

24.25

Application: Series3 models.

Description: Right hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -