Digital Dispensary

Product Sections


Best Sellers

Gasket Set for Solex 32PBI-2 Carburettor

Gasket Set for Solex 32PBI-2 Carburettor

7.66

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.
Description: Set of 6 gaskets and 8 fibre washers for this carburettor
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Differential Pinion

Oil Seal Differential Pinion

5.21

Application: Series 1, 2 & 3 Rover type differentials.

Description: Oil seal to nose of differential. Corteco/Gaco boxed.

Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").

Original part number: 217507.
find out more

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Gasket for Differential to Axle Casing

Gasket for Differential to Axle Casing

0.60

Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Page:   <<   <  1  2  3  4  5  ...   >   >>
Remover for Halfshaft Ref: 205-858
Application: Freelander 2 and Evoque.

Description: Remover for front half shaft.

Aproximate dimensions: 14cm(5.5") x 9.5cm(3.7") x 2.0cm(0.8").

Price: 87.30 (104.76 Including VAT at 20%)



Remover for Halfshaft
Differential Support Bracket Ref: JLR-205-972
Application: Freelander 2.

Description: Bracket assembly for supporting rear differential whilst under repair. Kit includes main bracket, supplementary bracket and 8 bolts.

Approximate dimensions: Main bracket 33.5cm(13.2"), x 19cm(7.5") x 17cm(6.7"). Small bracket 10cm(4") x 6cm(2.4") x 2.5cm(1").


Price: 127.11 (152.53 Including VAT at 20%)



Differential Support Bracket
Pinion Flange Remover-Replacer Ref: JLR-205-984
Application:Freelander 2, 2006 onwards.
Description: Two part tool for removing and replacing pinion drive flange on rear differential.
Approximate dimensions: Inner tool - 160mm( 6.3") long, 3/4"(19mm) socket drive, fine spline(24) 24mm(0.95") overall diameter. Outer tool - 150mm(5.9") long, with 135mm(5.3") reaction arm. double hex(12point) socket 41mmAF

Price: 143.97 (172.76 Including VAT at 20%)




People who bought this item also bought:
1. Installer Bearing and Seal Rear Differential (Ref: JLR-205-986)
Pinion Flange Remover-Replacer
Installer Bearing and Seal Rear Differential Ref: JLR-205-986
Application: Freelander 2.

Description: Installation tool for bearing and seal to rear differential pinion.

Approximate dimensions: Main body overall length 14.7cm(5.8"), main diameter 45mm(1.8"), collar diameter 62mm(2.45").. Black plastic adaptor overall diameter 95mm(3.74"), step 63mm(2.5")

Price: 76.00 (91.20 Including VAT at 20%)




People who bought this item also bought:
1. Pinion Flange Remover-Replacer (Ref: JLR-205-984)
Installer Bearing and Seal  Rear Differential
Adaptor Kit to remove Injection Pump Ref: 303-249-01
Application: Defender 2010 to 2016 with Puma TDCi engine.

Description: Adaptor kit for use with remover tool 303-249. To remove sprocket from injection pump on later versions where sprocket does not have threaded holes.

Approximate dimensions: Arms 68mm(2.7") long. Adator post for centre force screw 42mm(1.65") long.

Price: 49.72 (59.66 Including VAT at 20%)



Adaptor Kit to remove Injection Pump
Shim - Cam Timing Tool Ref: 303-530-04
Application: Range Rover Sport, Range Rover l322 and Discovery 3 where fitted with 4.4 litre V8 petrol engine.
Description: Shim 0.25mm thick for use with cam timing tool.
Approximate dimensions: Overall length 138mm(5.4"), width 20mm(0.8"), thickness 0.25mm(0.010")

Price: 18.72 (22.46 Including VAT at 20%)



Shim - Cam Timing Tool
Crank Timing Pin Ref: 303-645A
Application: Range Rover Sport, Range Rover l322 and Discovery 3 where fitted with 4.4 litre V8 petrol engine.
Description: Crankshaft timing pin.
Approximate dimensions: overall length 36.4mm(1.4")

Price: 43.98 (52.78 Including VAT at 20%)



Crank Timing Pin
Remover Inspection Plate Ref: 303-679A
Application: Defender 2007>2016 with Ford Puma TDCi engine.

Description: Tool to remove inspection plate to front of engine. 3 pegs engage with plate and then tool is rotated using 1/2" drive socketry.

Approximate dimensions:Overall diameter 10cm(4"),

Price: 16.49 (19.79 Including VAT at 20%)



Remover Inspection Plate
Aligner for Oil Pump Defender 2007 onwards Ref: 303-705
Application: Defender 2007 with the Ford Puma engine.

Description: Tool for aligning the engine oil pump on installation.

Approximate dimensions: 120mm(4.72") x 50mm(1.97") x 2mm(0.08")

Price: 15.47 (18.56 Including VAT at 20%)



Aligner for Oil Pump Defender 2007 onwards
Clutch Alignment Tool Ref: 303-1096
Application: Discovery 3 and Range Rover Sport when fitted with TDV6 engine and manual gearbox.

Description: Tool to align clutch plate to flywheel during assembly.

Approximate dimensions: Overall length 22.5cm(8.9"), body diameter 26mm(1.02"), pin 15mm(0.59") diameter x 22.7mm(0.9"0 long

Price: 51.42 (61.70 Including VAT at 20%)



Clutch Alignment Tool
Page:   <<   <  1  2  3  4  5  ...   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Outer Pinion Bearing

Outer Pinion Bearing

10.72

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for outer end of differential pinion gear. Timken bearing numbers HM88046/HM88010

Approximate dimensions: Outside diameter 2.7"(68.5mm), inside diameter 1.25"(31.8mm)., height 0.93"(23.5mm).


find out more

Inner Pinion Bearing - Differential

Inner Pinion Bearing - Differential

21.70

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for inner end of differential pinion gear. Timken bearing numbers HM801346X/HM801310

Approximate dimensions: Outside diameter 3.25"(82.5mm), inside diameter 1.5"(38mm)., height 1.22"(31mm).

find out more

Seal Kir for 1 1/8" Wheel Cylinders

Seal Kir for 1 1/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for rear wheel cylinders with bore of 1 1/8"(28.5mm). Kit has sufficient seals for both front wheel cylinders.

find out more

Seal Kit for 1 3/8" Wheel Cylinders

Seal Kit for 1 3/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for front wheel cyliders with bore of 1 3/8"(35mm). Kit has sufficient seals for both front wheel cylinders.


find out more

Outlet Nozzle - SU Fuel Pump

Outlet Nozzle - SU Fuel Pump

4.44

Application: Series 1 and early Series 2 models.

Description: Nozzle for outlet of SU fuel pumps. Allows push-on fuel hose connection to pump.

Approximate dimensions: Thread diameter 22mm(0.87"), nozzle diameter 7mm(0.28").

find out more

Wiper Arm Series 3 RH

Wiper Arm Series 3 RH

24.25

Application: Series3 models.

Description: Right hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -