Digital Dispensary
  •  
  • View Basket
  • Checkout
  • Items:, Value:

Product Sections


Best Sellers

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

11.04

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.30

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Nut and Bolt Kit for Propshafts

Nut and Bolt Kit for Propshafts

2.40

Application: Series 1, Series 2, Series 2A, Series 3 Land Rovers. All Defenders, Classic Range Rover, Range Rover 2 (38A), Discovery 1 and Discovery 2.

Description: Set of four 3/8UNF x 1.125" long bolts plus four short nyloc nuts.
find out more

Gaiter for Main Gear Lever

Gaiter for Main Gear Lever

2.16

Application: Series 1, Series 2, Series 2A and Series 3 4 & 6 cylinder models.

Description: Reproduction rubber gaiter for main gear lever.

Approximare dimensions: 11.5cm(4.5") square, 3.6cm(1.4") high.

find out more

Gasket Set for Series Gearboxes

Gasket Set for Series Gearboxes

4.20

Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Land Rover Parts & Land Rover Spares from Dingocroft - your reliable Land Rover parts specialist


Welcome to Dingocroft
new frontnew front
In celebration of our 30th anniversary, the shop front has received a make-over.

Particularly genuine and original equipment Land Rover parts and Land Rover spares. Based in UK and exporting to the world. We supply parts for Range Rover Classic, Range Rover Generation 2 (38A), Range Rover Generation 3, Range Rover Sport, Range Rover Evoque, Discovery 1, 2, 3 & 4, Defender, Freelander 1, Freelander 2, North American Spec. vehicles, Series 1 Series 2, Series 2A, Series 3, One-Ten, Ninety, One-Thirty and Military Models. Land Rover Series 1 parts 1948 to 1958 are now listed in our online shop.

We now stock Terrafirma Accessories.

We export Land Rover parts and Land Rover spares to USA and Canada!

DINGOCROFT offers World-wide export of Land Rover parts and Land Rover spares including USA and Canada, from a small item in a padded envelope to a container load (or anything in between).

We also offer mail order deliveries within the U.K. of Land Rover parts online.

Our delivery service operates within a 20 mile radius of High Wycombe. This provides Land Rover parts and Land Rover spares to your doorstep, whether you are a private customer, trade, garage or fleet customer. This service covers all of Buckinghamshire plus large areas of Oxfordshire, Berkshire, Hertfordshire, Middlesex and West London. This is free for orders greater than £75.00, otherwise a £4.00 delivery charge is made. We make frequent deliveries to the following towns; High Wycombe, Beaconsfield, Aylesbury, Marlow, Princes Risborough, Wendover, Slough, Maidenhead, Reading, Bracknell, Watford, Berkhamsted, Hemel Hempstead, Leighton Buzzard, Uxbridge, Hayes, West Drayton, Staines, Thame, Henley on Thames, Watlington.

DINGOCROFT stocks in excess of 12,000 lines of Land Rover parts and Land Rover spares and we are the largest independent Land Rover parts specialist in Buckinghamshire and probably in the Thames Valley. As well as Land Rover parts and Land Rover spares, we offer Land Rover manuals, Land Rover Special Tools (formerly Churchill Tools), Land Rover accessories and off-road equipment. Your one stop Land Rover parts shop.

Our sales counter is open to both trade and retail customers where our knowledgeable staff will help you select from our ever growing range of Land Rover parts and Land Rover spares, tools, accessories, books and all manner of things "Land Rover".

Opening Hours We are open weekdays from 8:30 to 18:00 with late night opening on Thursday to 8pm (20:00).

If you need help or assistance in anyway please telephone us on 01494 448367 or if outside Great Britain +44 1494 448367

Celebration TimeCelebration Time
Chris Barrie and most of our staff enjoy a photo opportunity.

Left to right; David Britnell (occasional help), Chris Hopkins, Tim Britnell, Chris Barrie, Peter Newcombe, Debbie, Pete Cook, Chris Cox and Henry Swanborough

Best Selling Items

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

11.04

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.30

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Nut and Bolt Kit for Propshafts

Nut and Bolt Kit for Propshafts

2.40

Application: Series 1, Series 2, Series 2A, Series 3 Land Rovers. All Defenders, Classic Range Rover, Range Rover 2 (38A), Discovery 1 and Discovery 2.

Description: Set of four 3/8UNF x 1.125" long bolts plus four short nyloc nuts.
find out more

Gaiter for Main Gear Lever

Gaiter for Main Gear Lever

2.16

Application: Series 1, Series 2, Series 2A and Series 3 4 & 6 cylinder models.

Description: Reproduction rubber gaiter for main gear lever.

Approximare dimensions: 11.5cm(4.5") square, 3.6cm(1.4") high.

find out more

Gasket Set for Series Gearboxes

Gasket Set for Series Gearboxes

4.20

Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more

New Products

Red Rotor Arm for 6 cylinder Distributor

Red Rotor Arm for 6 cylinder Distributor

7.20

Application: Series 2A and Series 3, 6 cylinder petrol with Lucas 25D6 distributor and Lucas 45D6.

Description: Replacement rotor arm. Modelled on the original, dependable 1960's design, but made from modern materials on the latest machinery to very close tolerances.
These 100% LUCAS COMPATIBLE RED ROTOR ARMS* will not let you down.
The integrally moulded brass inlay dispenses with the troublesome rivet used on most versions which is known to short circuit.
The increased insulation properties of the body makes them suitable for use with high voltage coils & electronic ignition kits.
The spring steel clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit, even on old & slightly reduced diameter mountings.

Previous part numbers: GRA102, 262704

Lucas Part number: 418726

find out more

Red Rotor Arm for Lucas 45D

Red Rotor Arm for Lucas 45D

7.20

Application: Lucas 45D 4cylinder distributor as fitted to Series 3 petrol engines.

Description: Reproduction rotor arm. Modelled on the original, dependable 1960's design, but made from modern materials on the latest machinery to very close tolerances.
These 100% LUCAS COMPATIBLE RED ROTOR ARMS* will not let you down.
The integrally moulded brass inlay dispenses with the troublesome rivet used on most versions which is known to short circuit.
The increased insulation properties of the body makes them suitable for use with high voltage coils & electronic ignition kits.
The spring steel clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit, even on old & slightly reduced diameter mountings.

Approximate dimensions: shaft diameter 14.5mm (0.57 inches), height 20mm (0.79 inches)

Lucas part number: 54422803
find out more

Red Rotor Arm for Lucas 25D

Red Rotor Arm for Lucas 25D

7.20

Application: Lucas 25D 4cylinder distributor as fitted to Series 2A and early Series 3 petrol engines. Also applicable to the DM2 distributor to Series 1 1954 to 1958.

Description: Reproduction rotor arm. Modelled on the original, dependable 1960's design, but made from modern materials on the latest machinery to very close tolerances.
These 100% LUCAS COMPATIBLE RED ROTOR ARMS* will not let you down.
The integrally moulded brass inlay dispenses with the troublesome rivet used on most versions which is known to short circuit.
The increased insulation properties of the body makes them suitable for use with high voltage coils & electronic ignition kits.
The spring steel clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit, even on old & slightly reduced diameter mountings.

Approximate dimensions: shaft diameter 14.5mm (0.57 inches), height 16.5mm (0.65 inches)

Lucas part number: 460051
find out more

Vacuum Unit - 25D type

Vacuum Unit - 25D type

69.60

Application: Series 2A 1958 to 19566with Lucas 25D distributor.

Description: Precisely made reproduction of the original Lucas vacuum advance unit for the 25D distributor. This is the early type with threaded connection for the vacuum pipe.

Approximate dimensions: Overall length 135mm(5.3"), outside diameter of diaphrapm 65mm(2.6")

Lucas part number: 54411598

find out more

Vacuum Unit - DM2 type

Vacuum Unit - DM2 type

69.60

Application: Series 1 1954 to 1958 with Lucas DM2 distributor.

Description: Precisely made reproduction of the original Lucas vacuum advance unit for the DM2 (40504A) distributor.

Approximate dimensions: Overall length 135mm(5.3"), outside diameter of diaphrapm 65mm(2.6")

Lucas part numbers: 421943 and 54411727



find out more

Pair of Clips for Distributor Cap

Pair of Clips for Distributor Cap

12.00

Application: Lucas 25D 4 cylinder ditributor as used on Series 2, Series 2A and Series 3.

Description: Nicely made reproduction clips for distributor cap. Sold as a pair.

Approximate dimensions: Overall length 77mm(3"), width 9mm(0.35")

Lucas part number: 421824

find out more

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Red Rotor Arm for 6 cylinder Distributor

Red Rotor Arm for 6 cylinder Distributor

7.20

Application: Series 2A and Series 3, 6 cylinder petrol with Lucas 25D6 distributor and Lucas 45D6.

Description: Replacement rotor arm. Modelled on the original, dependable 1960's design, but made from modern materials on the latest machinery to very close tolerances.
These 100% LUCAS COMPATIBLE RED ROTOR ARMS* will not let you down.
The integrally moulded brass inlay dispenses with the troublesome rivet used on most versions which is known to short circuit.
The increased insulation properties of the body makes them suitable for use with high voltage coils & electronic ignition kits.
The spring steel clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit, even on old & slightly reduced diameter mountings.

Previous part numbers: GRA102, 262704

Lucas Part number: 418726

find out more

Red Rotor Arm for Lucas 45D

Red Rotor Arm for Lucas 45D

7.20

Application: Lucas 45D 4cylinder distributor as fitted to Series 3 petrol engines.

Description: Reproduction rotor arm. Modelled on the original, dependable 1960's design, but made from modern materials on the latest machinery to very close tolerances.
These 100% LUCAS COMPATIBLE RED ROTOR ARMS* will not let you down.
The integrally moulded brass inlay dispenses with the troublesome rivet used on most versions which is known to short circuit.
The increased insulation properties of the body makes them suitable for use with high voltage coils & electronic ignition kits.
The spring steel clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit, even on old & slightly reduced diameter mountings.

Approximate dimensions: shaft diameter 14.5mm (0.57 inches), height 20mm (0.79 inches)

Lucas part number: 54422803
find out more

Red Rotor Arm for Lucas 25D

Red Rotor Arm for Lucas 25D

7.20

Application: Lucas 25D 4cylinder distributor as fitted to Series 2A and early Series 3 petrol engines. Also applicable to the DM2 distributor to Series 1 1954 to 1958.

Description: Reproduction rotor arm. Modelled on the original, dependable 1960's design, but made from modern materials on the latest machinery to very close tolerances.
These 100% LUCAS COMPATIBLE RED ROTOR ARMS* will not let you down.
The integrally moulded brass inlay dispenses with the troublesome rivet used on most versions which is known to short circuit.
The increased insulation properties of the body makes them suitable for use with high voltage coils & electronic ignition kits.
The spring steel clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit, even on old & slightly reduced diameter mountings.

Approximate dimensions: shaft diameter 14.5mm (0.57 inches), height 16.5mm (0.65 inches)

Lucas part number: 460051
find out more

Vacuum Unit - 25D type

Vacuum Unit - 25D type

69.60

Application: Series 2A 1958 to 19566with Lucas 25D distributor.

Description: Precisely made reproduction of the original Lucas vacuum advance unit for the 25D distributor. This is the early type with threaded connection for the vacuum pipe.

Approximate dimensions: Overall length 135mm(5.3"), outside diameter of diaphrapm 65mm(2.6")

Lucas part number: 54411598

find out more

Vacuum Unit - DM2 type

Vacuum Unit - DM2 type

69.60

Application: Series 1 1954 to 1958 with Lucas DM2 distributor.

Description: Precisely made reproduction of the original Lucas vacuum advance unit for the DM2 (40504A) distributor.

Approximate dimensions: Overall length 135mm(5.3"), outside diameter of diaphrapm 65mm(2.6")

Lucas part numbers: 421943 and 54411727



find out more

Pair of Clips for Distributor Cap

Pair of Clips for Distributor Cap

12.00

Application: Lucas 25D 4 cylinder ditributor as used on Series 2, Series 2A and Series 3.

Description: Nicely made reproduction clips for distributor cap. Sold as a pair.

Approximate dimensions: Overall length 77mm(3"), width 9mm(0.35")

Lucas part number: 421824

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -