Digital Dispensary

Product Sections


Best Sellers

Gasket Set for Solex 32PBI-2 Carburettor

Gasket Set for Solex 32PBI-2 Carburettor

7.66

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.
Description: Set of 6 gaskets and 8 fibre washers for this carburettor
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Differential Pinion

Oil Seal Differential Pinion

5.21

Application: Series 1, 2 & 3 Rover type differentials.

Description: Oil seal to nose of differential. Corteco/Gaco boxed.

Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").

Original part number: 217507.
find out more

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Gasket for Differential to Axle Casing

Gasket for Differential to Axle Casing

0.60

Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Fuel System
Page:   <<   <  1  2  3  4   >   >>
Needle Valve Float Chamber Ref: 260164
Application: Series 1 1.6ltr & 2.0ltr engines with Solex 32PBI carburetter.
Description: Needle valve in float chamber.
Solex part number 51305/17.

Price: 19.22 (23.06 Including VAT at 20%)




People who bought this item also bought:
1. Rubber Peg for Wiper Blade (Ref: ZZB00100)
2. Gasket Set for Solex 32PBI-2 Carburettor (Ref: 274895)
3. Wiper Blade (Ref: 261504)
Needle Valve Float Chamber
Throttle Pedal Shaft Ref: 236658
Application: Series 1, Series 2 and Series 3.
Description: Shaft for throttle (accelerator) pedal.
Approximate dimensions: overall length 46cm(18.1"), diameter 7/16"(11mm)

Price: 4.96 (5.95 Including VAT at 20%)



Throttle Pedal Shaft
Ball End, Throttle Lever Ref: 1481L
Application: Series 1, Series 2 and Series 3.

Description: Ball end for throttle levers. Requires peening over to fix to levers.

Approximate dimensions: Ball diameter 5/16"(7.8mm), overall length 17.5mm(0.7")

Price: 3.49 (4.19 Including VAT at 20%)




People who bought this item also bought:
1. S1 86/88" Brake Pipe Set LHD (Ref: ZZGL5608)
2. Steering Box Repair Kit (Ref: STRGBOXKIT01)
3. Universal Joint for Front Half-Shafts (Ref: RTC3690)
Ball End, Throttle Lever
Stop Clip - Accelerator Relay Shaft Ref: 269132
Application: Series 1 diesel, Series 2 and Series 3.
Description: Stop clip to retain throttle shafts in brackets. Used on various models from 1954 to 1984. For 7/16"(11mm) diameter shafts.

Price: 0.50 (0.60 Including VAT at 20%)




People who bought this item also bought:
1. Steering Box Repair Kit (Ref: STRGBOXKIT01)
2. Universal Joint for Front Half-Shafts (Ref: RTC3690)
3. Special Stud - Swivel Pin Housing (Ref: 90508153)
Stop Clip - Accelerator Relay Shaft
Return Spring - Iinjector Pump Ref: 277502
Application: Series 1 and Series 2 diesel.
Description: Return spring for throttle linkage on diesel injector pump.
Approximate dimensions: overall length 85mm(3.3"), ovarall diameter 14mm(0.55")

Price: 0.85 (1.02 Including VAT at 20%)



Return Spring - Iinjector Pump
Bracket - Accelerator Shaft Ref: 236998
Application: Series 1, Series 2 and Series 3.
Description: Support bracket for accelerator shafts.

Price: 1.50 (1.80 Including VAT at 20%)



Bracket - Accelerator Shaft
Bracket - Accelerator Shaft Ref: 236665
Application: Series 1, Series 2 and Series 3.
Description: Support bracket for accelerator shafts.

Price: 7.45 (8.94 Including VAT at 20%)



Bracket - Accelerator Shaft
Anchor Plate for Stop Spring Ref: 277565
Application: Series 1, Series 2 and Series 3 diesel models.
Description: Anchor plare for injection pump stop spring.
Approximate dimensions: overall length 30mm(1.2")

Price: 0.50 (0.60 Including VAT at 20%)



Anchor Plate for Stop Spring
Pin for Bell Crank on Injector Pump Ref: 277454
Application: Series 1 and Series 2 diesel.
Description: Pin for bell crank on head of injector pump for throttle linkage.
Approximate dimensions: overall length 40mm(1.6"), overall diameter 9.7mm(3/8"), thread 1/4" BSF.

Price: 1.95 (2.34 Including VAT at 20%)



Pin for Bell Crank on Injector Pump
Sender Unit - Fuel Tank Ref: 236017D
Application: Series 1 and Series 2/2A to suffix C inclusive.
Description: Reproduction moving coil type sender unit. This is a 'universal' unit and requires the float arm lengthening to work properly with the Land Rover fuel tank. Supplied with cork gasket.

Price: 69.61 (83.53 Including VAT at 20%)



Sender Unit - Fuel Tank
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Fuel System
Page:   <<   <  1  2  3  4   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Outer Pinion Bearing

Outer Pinion Bearing

10.72

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for outer end of differential pinion gear. Timken bearing numbers HM88046/HM88010

Approximate dimensions: Outside diameter 2.7"(68.5mm), inside diameter 1.25"(31.8mm)., height 0.93"(23.5mm).


find out more

Inner Pinion Bearing - Differential

Inner Pinion Bearing - Differential

21.70

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for inner end of differential pinion gear. Timken bearing numbers HM801346X/HM801310

Approximate dimensions: Outside diameter 3.25"(82.5mm), inside diameter 1.5"(38mm)., height 1.22"(31mm).

find out more

Seal Kir for 1 1/8" Wheel Cylinders

Seal Kir for 1 1/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for rear wheel cylinders with bore of 1 1/8"(28.5mm). Kit has sufficient seals for both front wheel cylinders.

find out more

Seal Kit for 1 3/8" Wheel Cylinders

Seal Kit for 1 3/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for front wheel cyliders with bore of 1 3/8"(35mm). Kit has sufficient seals for both front wheel cylinders.


find out more

Outlet Nozzle - SU Fuel Pump

Outlet Nozzle - SU Fuel Pump

4.44

Application: Series 1 and early Series 2 models.

Description: Nozzle for outlet of SU fuel pumps. Allows push-on fuel hose connection to pump.

Approximate dimensions: Thread diameter 22mm(0.87"), nozzle diameter 7mm(0.28").

find out more

Wiper Arm Series 3 RH

Wiper Arm Series 3 RH

24.25

Application: Series3 models.

Description: Right hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -