Digital Dispensary

Product Sections


Best Sellers

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Seal Kit for Brake Master Cylinder

Seal Kit for Brake Master Cylinder

19.80

Application: Series One from 1948 to 1958.
Description: Reproduction seal kit for brake master cylinder. Suits all short wheel base models. Not suitable for long wheel base models.
Original part number 278524
find out more

Anchor Plate for 10inch brake shoes

Anchor Plate for 10inch brake shoes

8.44

Anchor plate for use with 10inch brakes - see kit above. One anchor plate is used with each pair of shoes. These do not need replacing with every change of brake shoes, but they do become worn over several years use. Sold singly.
Approximate dimensions: 78mm x 45mm x 5mm.

Application: see STC2796DKIT above.
find out more

Felt Seal Stub Shaft to Drive Flange

Felt Seal Stub Shaft to Drive Flange

0.48

Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Split Pin - Shocker Retention

Split Pin - Shocker Retention

0.25

Application: Series 1, Series 2 and Series 3.

Description: Replacement split pin for retaining shock absorber to bottom plate of spring.

Approximate dimensions: Overall length 55.5mm(2.2"), diameter 6mm(0.24")

find out more

Dust Cap for Bleed Screw

Dust Cap for Bleed Screw

0.30

Application: Suitable for all bleed screws.
Description: Soft plastic dust cap for bleed screws.
Approximate dimensions: length 15mm(0.6"), diameter 8mm (0.3")
Original part number 234957
find out more

Screw for retaining Brake Drums

Screw for retaining Brake Drums

0.25

Application: Series 1, 2 & 3.
Description: Countersunk head screw 3/8"BSW by 5/8" long.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Fuel System Parts for Land Rover Series 2 and 3
Page:  1  2  3  4   >   >>
Genuine Diesel Fuel Filter Element - 90517711 Ref: 90517711
Genuine diesel fuel filter element with 4 'O' ring seals.

Application:
Series 2A & 3 2.25 diesel.
Defender (inc Ninety & One Ten) 2.25 diesel, 2.5 diesel and 2.5 diesel turbo.

Approx dimensions 83mm diameter x 71mm long.

Old part number: RTC6079

Price: 4.39 (5.27 Including VAT at 20%)



Genuine Diesel Fuel Filter Element - 90517711
Replacement Equivalent to 90517711 Ref: RTC6079D
Crosland diesel fuel filter element with 5 'O' ring seals - 522. (Coopers or Fram may be supplied depending on availability).
Application:
Series 2A & 3 2.25 diesel.
Defender (inc Ninety & One Ten) 2.25 diesel, 2.5 diesel and 2.5 diesel turbo.
Approx dimensions 83mm diameter x 71mm long.

Price: 1.80 (2.16 Including VAT at 20%)



Replacement Equivalent to 90517711
Replacement Equivalent to 90606262 Ref: 90606262
Application: All those vehicles fitted with Facet electric fuel pump, Range Rover Classic 1975 to 1985, S3 109V8, S3 6cyl petrol, Defender 2.5 petrol, Defender V8 and possibly some others.

Price: 6.48 (7.78 Including VAT at 20%)



Replacement Equivalent to 90606262
Replacement Equivalent to JS660L Ref: JS660L
Mann petrol fuel filter element P65/1 (Alternative manufacturer may be supplied depending on availability)

Application:
Series 3 109 V8
Defender 2.5 and 3.5 (carb type) petrol.
Discovery I 3.5 V8 carb type.
Range Rover Classic 3.5 V8 carb type.

Approx dimensions: 56mm dia x 38mm long.

Price: 2.41 (2.89 Including VAT at 20%)



Replacement Equivalent to JS660L
Reproduction Solex 32PBI-2 Carburrettor Ref: 264664D
Application: Series 1 and Series 2 with 2 litre petrol (gasolene) engine. 1954 to 1960 approx.

Description: Reproduction Solex 32PBI-2 carburrettor.

Temporarily out of stock, hopefully back in stock early September.



Price: 123.98 (148.78 Including VAT at 20%)


Reproduction Solex 32PBI-2 Carburrettor
Rebuild kit for Solex 40PA10-5(6) Carburetor Ref: 507687
Application; Series 2A 2.25 petrol (gasolene) when fitted with the Solex 40PA10 carburetor.
Description: Rebuild kit containing gaskets, diaphragm, throttle spindle and disc, washers etc.


Price: 42.86 (51.43 Including VAT at 20%)



Rebuild kit for Solex 40PA10-5(6) Carburetor
Gasket Set for Solex 40PA10-5 Ref: 507693
Application; Series 2A 2.25 petrol (gasolene) when fitted with the Solex 40PA10 carburetor.
Description: Original Equipment gasket set.

Price: 10.62 (12.74 Including VAT at 20%)




People who bought this item also bought:
1. Sealed Body Rivet - bag of 10 (Ref: 78248x10)
2. Spring Ring, Boot to Body of Steering Ball Joint (Ref: 214685)
3. Cap for Hub Flange (Ref: 219098)
Gasket Set for Solex 40PA10-5
Accelerator Diaphragm Kit Solex 40PA10 Ref: 503900
Application; Series 2A 2.25 petrol (gasolene) when fitted with the Solex 40PA10 carburetor.
Description: Diaphragm, gasket and springs for accelerator pump.

Price: 14.95 (17.94 Including VAT at 20%)



Accelerator Diaphragm Kit Solex 40PA10
Float for Solex 40PA10-5 Carburetor Ref: 503912
Application; Series 2A 2.25 petrol (gasolene) when fitted with the Solex 40PA10 carburetor.
Description: Brass float for this carburetor

Price: 17.56 (21.07 Including VAT at 20%)



Float for Solex 40PA10-5 Carburetor
Copy of Zenith 36IV Ref: ERC2886D
Application: Series 2, 2A and 3 when fitted with 2.25 litre petrol engine.
Description: Chinese manufactured copy of the Zenith 36IV. Appears to be very well made and we are hopeful that these carburetors will live up to their promise.

Price: 60.50 (72.60 Including VAT at 20%)



Copy of Zenith 36IV
Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Fuel System Parts for Land Rover Series 2 and 3
Page:  1  2  3  4   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Piston Assembly 2.4TDCI

Piston Assembly 2.4TDCI

122.63

Application: Defender from 2007 to 2012 with 2.4 litre TDCI engine.

Description: Standard size piston for 89.90mm bore. Supplied with rings, gudgeon pin and circlips. Made by Nural a Federal Mogul company.



find out more

Electric Fuel Pump - Series 1

Electric Fuel Pump - Series 1

100.44

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Repair Kit for Handbrake Adjuster

Repair Kit for Handbrake Adjuster

4.45

Application: Series 2A and Series 3.

Description: Old stock Lucas Girling repair kit for handbrake adjuster. Includes adjusting screw and wedges plus period tube of brake grease.


find out more

Injector for BMW M57 Diesel Engine

Injector for BMW M57 Diesel Engine

183.77

Application: Range Rover L322 with BMW M57 3.0litre diesel engine.

Description: Reconditioned Bosch injector for the M57 engine. Outright purchase, we do not need your old injector in vexchange.

Approximate dimensions: Overall length 22cm(8.7").

find out more

Bearing and Seals kit for Freelander 1 IRD

Bearing and Seals kit for Freelander 1 IRD

72.54

Application: Freelander 1 IRD unit except V6 model.

Description: Set of 7 OE spec bearings and 4 seals to overhaul the intermediate reduction drive unit. This kit does not include the plate for the oil cooler.

find out more

Rear Diff Repair Kit - Freelander2

Rear Diff Repair Kit - Freelander2

103.14

Application: Freelander 2 and Evoque

Description: Repair kit of OE bearings and seals for the rear differential. Kit includes 4x taper roller bearings, 3x oil seals, 2x 'O' rings, collapsible spacer and pinion nut.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -