Digital Dispensary

Product Sections


Best Sellers

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Seal Kit for Brake Master Cylinder

Seal Kit for Brake Master Cylinder

19.80

Application: Series One from 1948 to 1958.
Description: Reproduction seal kit for brake master cylinder. Suits all short wheel base models. Not suitable for long wheel base models.
Original part number 278524
find out more

Anchor Plate for 10inch brake shoes

Anchor Plate for 10inch brake shoes

8.44

Anchor plate for use with 10inch brakes - see kit above. One anchor plate is used with each pair of shoes. These do not need replacing with every change of brake shoes, but they do become worn over several years use. Sold singly.
Approximate dimensions: 78mm x 45mm x 5mm.

Application: see STC2796DKIT above.
find out more

Felt Seal Stub Shaft to Drive Flange

Felt Seal Stub Shaft to Drive Flange

0.48

Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Split Pin - Shocker Retention

Split Pin - Shocker Retention

0.25

Application: Series 1, Series 2 and Series 3.

Description: Replacement split pin for retaining shock absorber to bottom plate of spring.

Approximate dimensions: Overall length 55.5mm(2.2"), diameter 6mm(0.24")

find out more

Dust Cap for Bleed Screw

Dust Cap for Bleed Screw

0.30

Application: Suitable for all bleed screws.
Description: Soft plastic dust cap for bleed screws.
Approximate dimensions: length 15mm(0.6"), diameter 8mm (0.3")
Original part number 234957
find out more

Screw for retaining Brake Drums

Screw for retaining Brake Drums

0.25

Application: Series 1, 2 & 3.
Description: Countersunk head screw 3/8"BSW by 5/8" long.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Engine Parts for Land Rover Series 2 and 3
Page:  1  2  3  4  5   >   >>
Cylinder Liner Ref: 516498
Application: Series 1 & 2 2litre engine, Series 2a & 3 2.6litre 6cyl engine.

Description: Liner for cylinder block on the 2litre and 2.6litre side exhaust, overhead inlet engines.

Approximate dimensions: Overall length 193mm(7.6"), outside diameter 81.5mm(3.2"), inside diameter 78.3mm(3.08")

Price: 45.00 (54.00 Including VAT at 20%)



Cylinder Liner
Rear Oilseal for Crankshaft Ref: 275807
Application: Series 1 2.0 litre petrol engine from 1955 - 1958, Series 2 2.0 litre petrol engine from 1958 to 1961.

Description: Reproduction pair of half seals for rear of crankshaft. Bonded seals onto aluminium carriers.

Approximate dimensions: Overall diameter 14cm( 5.5")

Price: 66.65 (79.98 Including VAT at 20%)




People who bought this item also bought:
1. Gasket Inlet Manifold to Cylinder Head (Ref: 9179)
2. Gasket Water Branch to Cylinder Head (Ref: 210447)
Rear Oilseal for Crankshaft
Decoke Gasket Set Ref: STC1567=
Application: 2.25 and 2.5 litre petrol engines for Series 2A, Series 3 and Defender.
Description: Set of gaskets for cylinder head, also called decoke gasket set. Manufactured by Payen (part of Federal Mogul) features composite head gasket (which does not require re-torqueing) and 46 other gaskets and seals. This set is "asbestos free".

Price: 26.50 (31.80 Including VAT at 20%)



Decoke Gasket Set
Decoke Gasket Set 2.6 litre 6 cylinder Ref: RTC3333
Application: Series 2A and Series 3 when fitted with the straight 6, 2.6 litre petrol(gasolene) engine.

Description: Gasket set by Payen for cylinder head overhaul of the above engine.

Old part numbers: GEG1214, 605105

Price: 21.05 (25.26 Including VAT at 20%)



Decoke Gasket Set 2.6 litre 6 cylinder
Gasket Set Exhaust Manifold Ref: RTC3326
Application: 2.6ltr Series 2A & 3 petrol.

Description: Replacement set of 3 gaskets for jointing exhaust manifold to cylinder head.

Price: 6.71 (8.05 Including VAT at 20%)



Gasket Set Exhaust Manifold
Manifold Gasket 4cyl Petrol Ref: 274171=
Application: 2.25 and 2.5 litre petrol engines for Series 2A, Series 3 and Defender.
Description: Non genuine gasket between manifolds and cylinder head.

Price: 0.85 (1.02 Including VAT at 20%)



Manifold Gasket 4cyl Petrol
Rocker Box Gasket 4cyl Petrol Ref: ERR4933
Application: 2.25 and 2.5 litre petrol engines for Series 2A, Series 3 and Defender.
Description: Gasket for rocker box (valve cover). This is a non-genuine gasket, it is self adhesive on one face to ease assembly and improve sealing.

Price: 1.27 (1.52 Including VAT at 20%)



Rocker Box Gasket 4cyl Petrol
Rocker Box Fitting Kit Ref: 247121KIKT
Application: 2.25 petrol engine in Series2, Series2A and Series3.

Description: Smatren up the top of your rocker box with this set of 3 domed nuts, 3 aluminium sealing washer, 3 domed washers and 3 rubber seals.


Price: 15.00 (18.00 Including VAT at 20%)



Rocker Box Fitting Kit
Cylinder Head Gasket 4cyl Petrol Engine Ref: ERC6380=
Application: 2.25 and 2.5 litre petrol engines for Series 2A, Series 3 and Defender.
Description: Composite cylinder head gasket by 'Elring'. Composite head gaskets do not require re-torquing as the copper type do.

Price: 9.59 (11.51 Including VAT at 20%)



Cylinder Head Gasket 4cyl Petrol Engine
Banjo Bolt for Oil Feed Pipe Ref: ETC4498
Application: Late Series3 4 cylinder petrol and diesel engines with metric fixings (from approx 1980). Defender with 2.25 petrol, 2.5 petrol, 2.5 diesel and 2.5 turbo diesel.

Description: Banjo bolt for both ends of the oil feed pipe that delivers lubricating oil to cylinder head from cylinder block.

Approcimate dimensions: Head is 17mm(0.7") across flats, overall length 32mm(1.26"), thread is M10.

Price: 0.95 (1.14 Including VAT at 20%)



Banjo Bolt for Oil Feed Pipe
Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Engine Parts for Land Rover Series 2 and 3
Page:  1  2  3  4  5   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Piston Assembly 2.4TDCI

Piston Assembly 2.4TDCI

122.63

Application: Defender from 2007 to 2012 with 2.4 litre TDCI engine.

Description: Standard size piston for 89.90mm bore. Supplied with rings, gudgeon pin and circlips. Made by Nural a Federal Mogul company.



find out more

Electric Fuel Pump - Series 1

Electric Fuel Pump - Series 1

100.44

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Repair Kit for Handbrake Adjuster

Repair Kit for Handbrake Adjuster

4.45

Application: Series 2A and Series 3.

Description: Old stock Lucas Girling repair kit for handbrake adjuster. Includes adjusting screw and wedges plus period tube of brake grease.


find out more

Injector for BMW M57 Diesel Engine

Injector for BMW M57 Diesel Engine

183.77

Application: Range Rover L322 with BMW M57 3.0litre diesel engine.

Description: Reconditioned Bosch injector for the M57 engine. Outright purchase, we do not need your old injector in vexchange.

Approximate dimensions: Overall length 22cm(8.7").

find out more

Bearing and Seals kit for Freelander 1 IRD

Bearing and Seals kit for Freelander 1 IRD

72.54

Application: Freelander 1 IRD unit except V6 model.

Description: Set of 7 OE spec bearings and 4 seals to overhaul the intermediate reduction drive unit. This kit does not include the plate for the oil cooler.

find out more

Rear Diff Repair Kit - Freelander2

Rear Diff Repair Kit - Freelander2

103.14

Application: Freelander 2 and Evoque

Description: Repair kit of OE bearings and seals for the rear differential. Kit includes 4x taper roller bearings, 3x oil seals, 2x 'O' rings, collapsible spacer and pinion nut.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -