Spider Bypass Link Cable
Application: Discovery 1 1995 to 1998 approx, where fitted with original immobilisation and alarm system.
Description: Small wiring harness to bypass the "spider" .
See http://forums.lr4x4.com/index.php?showtopic=86 for full instructions on how to fit.
find out more
Connector Kit for Defender Switches
Application: Defender 2001 to 2006 with the facelift dash.
Description: Connector kit for auxillary switches on centre dash. This is a direct fit to the front fog lamp switch YUG000540LNF, but will fit the other switches if the splines are removed with a small sharp blade such as a modelling scalpel.
find out more
Connector Kit for Bulb Holders
Application: Single pole bulb holders on Defender 1995 onwards, Discovery 1, Discovery 2, Range Rover Classic late,and Range Rover 38A 1995 to 2001.
Description: Connection kit for replacing plug that connects to single pole bulb holder XPB100180.
find out more
Nut and Bolt Kit for Propshafts
Application: Series 1, Series 2, Series 2A, Series 3 Land Rovers. All Defenders, Classic Range Rover, Range Rover 2 (38A), Discovery 1 and Discovery 2.
Description: Set of four 3/8UNF x 1.125" long bolts plus four short nyloc nuts.
find out more
Replacement Jate Ring and Fixings
Replacement Jate Ring with fixing bolt, nut and spacing washer. Standard equipment on military Defenders. Fixes to chassis rail at front or rear of vehicle. Uses existing mounting holes, so no drilling required.
Application: Defender, Classic Range Rover and Discovery 1.
find out more
Socket for hub nuts
Application: Series 1 - 3, Range Rover Classic, Discovery 1 and Defender.
Description: 52mm deep socket, 1/2" drive for hub locking nuts.
find out more
Rebuild kit for Solex 32PBI-2 Carburettor
Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor. Zenith part number ZRK17.
Description: A fairly comprehensive kit of parts to rebuild this carburettor.
find out more
Standard Set Plus for Defender, Classic Range Rover and Discovery
Standard Set Plus of Polybush covers both ends of front radius arms, both ends of rear lower link, Panhard rod bushes, plus rear 'A' frame to chassis.
Application: Defender 1994 to 2001, Classic Range Rover 1986 to 1995, Discovery I 1989 to 1999.
Available in Classic and Comfort Formulas.
find out more
Hub Bearing Kit - Defender, Discovery and Classic Range Rover
Application: Defender rear from approx 1985 to 1993, Discovery 1 to 'JA' chassis number (1992) front and rear, Range Rover Classic 1985 to 1995 non-ABS front and rear.
Description: Kit of parts to service one wheel hub. Kit comprises a pair of Timken wheel bearings, Gaco inner seal, replacement outer seal, seal spacer, 2x flange gaskets and hub nut locker.
find out more
These Superb Prices are ONLY available when you order ON-LINE
Haven't found what you want? Then try our quotation service.
Rear Brake Cylinder
Application: Freelander One to 'YA'.
Description: Original equipment rear brake cylinder for vehicles to approx 2000. These cylinders are not handed.
Approximate dimensions: Casting 4.7cm(1.85") long
find out more
Caliper Seal Kit
Application: Freelander One from '1A'.
Description: Replacement seals to service both front calipers on later vehicles with vented discs.
Approximate dimensions: 2 seals with outside diameter of 7cm(2.8"), 2 'O' rings with outside diameter of 6cm(2.4")
find out more
Kit of Brake Caliper Guide Pins
Application: Freelander One from '1A'.
Description: Genuine kit of guide pins to service pair of front brake calipers.
Approximate dimensions: 2 pins 5.9cm(2.3") long, 2 pins 7.0cm(2.8") long.
find out more
Front Brake Disc - Vented
Application: Freelander One from '1A'.
Description: Replacement vented brake disc for front wheels. Priced as single disc, but strongly recommended to be fitted in pairs.
Approximate dimensions: Overall diameter 27.6cm(10.9"), 2.0cm(0.8") thick, offset 3.2cm(1.3")
find out more
Fixing Clip kit for Front Pads
Application: Freelander One from '1A'.
Description: Genuine set of 4 fixing clips for front brake pads on vehicles with vented front discs.
Approximate dimensions: Each clip is 7.5cm(3") long.
find out more
Front Brake Pad Set - Genuine
Application: Freelander One from '1A'.
Description: Genuine boxed front brake pad set for later models with vented discs. Supplied with 4 new fixing bolts.
Approximate dimensions: Each pad is 13cm(5.1") long by 5.5cm(2.1") wide.
Original part number: SFP500100.
find out more
Front Brake Pad Set
Application: Freelander One from '1A'.
Description: Mintex boxed front brake pad set for later models with vented discs.
Approximate dimensions: Each pad is 13cm(5.1") long by 5.5cm(2.1") wide.
find out more
Brake Disc - non vented
Application: Freelander One to 'YA'.
Description: Replacement solid brake disc for front wheels. Priced as single disc, but stronglt recommended to be fitted in pairs.
Approximate dimensions: Overall diameter 26.2cm(10.3"), 1.4cm(0.55") thick, offset 4cm(1.6")
find out more
Front Brake Pad Set
Application: Freelander One to YA.
Description: Delphi boxed set of front brake pads for early models with solid discs.
Approximate dimensions: Each pad is 13cm(5.1") long by 6.7cm(2.6") wide.
find out more
Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain
Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England) email: sales@dingocroft.co.uk
Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -
SearchQuest: Internet Marketing, SEO