Digital Dispensary

Product Sections


Best Sellers

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Seal Kit for Brake Master Cylinder

Seal Kit for Brake Master Cylinder

19.80

Application: Series One from 1948 to 1958.
Description: Reproduction seal kit for brake master cylinder. Suits all short wheel base models. Not suitable for long wheel base models.
Original part number 278524
find out more

Anchor Plate for 10inch brake shoes

Anchor Plate for 10inch brake shoes

8.44

Anchor plate for use with 10inch brakes - see kit above. One anchor plate is used with each pair of shoes. These do not need replacing with every change of brake shoes, but they do become worn over several years use. Sold singly.
Approximate dimensions: 78mm x 45mm x 5mm.

Application: see STC2796DKIT above.
find out more

Felt Seal Stub Shaft to Drive Flange

Felt Seal Stub Shaft to Drive Flange

0.48

Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Split Pin - Shocker Retention

Split Pin - Shocker Retention

0.25

Application: Series 1, Series 2 and Series 3.

Description: Replacement split pin for retaining shock absorber to bottom plate of spring.

Approximate dimensions: Overall length 55.5mm(2.2"), diameter 6mm(0.24")

find out more

Dust Cap for Bleed Screw

Dust Cap for Bleed Screw

0.30

Application: Suitable for all bleed screws.
Description: Soft plastic dust cap for bleed screws.
Approximate dimensions: length 15mm(0.6"), diameter 8mm (0.3")
Original part number 234957
find out more

Screw for retaining Brake Drums

Screw for retaining Brake Drums

0.25

Application: Series 1, 2 & 3.
Description: Countersunk head screw 3/8"BSW by 5/8" long.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Clutch Parts for Land Rover Series 2 and 3
Page:  1  2  3   >   >>
Clutch Plate 9" Ref: 591704
Application: Series 1, Series 2 and 2A. Where 9" clutch is used.

Description: Nine inch diameter clutch plate by 'Automotive Products' (HB8748). This has a ten spline centre.

Approximate dimensions: overall diameter 230mm.

Previous part number: GCP109

Price: 36.20 (43.44 Including VAT at 20%)



Clutch Plate 9
Clutch Cover 9" Ref: 591705
Application: Series 1, Series 2 and 2A. Where 9" clutch is used.
Description: Clutch cover plate (pressure plate) for nine inch diameter friction disc. By 'Automotive Productsi' (HA2520).

Currently unavailable - 'tooling broken'

Price: 67.88 (81.46 Including VAT at 20%)


Clutch Cover 9
Clutch Plate 9.5" Ref: 8510290
Application: Series 2A (optional use) and Series 3.

Description: 9.5" diameter clutch plate (friction disc) by AP Driveline (HB8117). 10 spline centre.

Approximate dimensions: overall diameter 240mm.

Price: 37.63 (45.16 Including VAT at 20%)




People who bought this item also bought:
1. Series 2A Optional 9.5" Clutch Cover (Ref: 571228)
Clutch Plate 9.5
Series 2A Optional 9.5" Clutch Cover Ref: 571228
Application: Series 2A with optional 9.5" clutch. This option was quite common on North American market Series 2A, but fairly rare in other markets.
Description: Clutch cover (pressure plate) for use with 9.5" diameter clutch plate on Series 2A vehicles with the part syncomesh gearbox. NOT for use in Series 3 or Series 2A where full syncromesh gearbox used.

Temporarily out of stock, due date October 2017.

Price: 57.50 (69.00 Including VAT at 20%)



People who bought this item also bought:
1. Clutch Plate 9.5" (Ref: 8510290)
Series 2A Optional 9.5
Clutch Cover 9.5" Ref: 576557
Application: Series 3 4cylinder and 6 cylinder engines.
Description: Clutch cover (pressure plate) for use with 9.5" clutch plates. 'Borg & Beck Delphi' type HE5584.

Price: 45.00 (54.00 Including VAT at 20%)



Clutch Cover 9.5
Clutch Release Bearing Series1 & 2A Ref: STC1130D
Application: Series1, Series2 and 2A part syncromesh gearbox with the unsealed clutch release mechanism. This is the usual setup on the Series 2 and 2A. This bearing is also used in various gearboxes and transfer boxes.

Description: Single row ball bearing by FAG, type 6207.C3.

Approximate dimensions: overall diameter 72mm (2.83"), inside diameter 35mm (1.38"), thickness 17mm (0.67").

Price: 8.50 (10.20 Including VAT at 20%)




People who bought this item also bought:
1. Bearing Clutch Release Series 2A (Ref: 268053d)
Clutch Release Bearing Series1 & 2A
Bearing Clutch Release Series 2A Ref: 268053d
Application: Series 2A with sealed clutch release mechanism.

Description: Replacement narrow single row ball bearing assembly for clutch release mechanism. This sealed arrangement was optional for most markets and consequently is not common. Bearing number is 98207.

Approximate dimensions: Outside diameter 70mm(2.76"), inside diameter 35mm(1.38"), thichness 10mm(0.4").

Price: 18.85 (22.62 Including VAT at 20%)




People who bought this item also bought:
1. Clutch Release Bearing Series1 & 2A (Ref: STC1130D)
Bearing Clutch Release Series 2A
Clutch Release Bearing - S3 type Ref: FRC9568D
Application: Series 3 four and six cylinder engines. Range Rover Classic.

Description: Original design but non genuine release bearing from Bearmach. This design works better with Series 3 clutch covers than the later type bearing (FTC5200).

Approximate dimensions: Outside diameter 76.5mm(3"), length 51mm(2"), inside diameter 39.5mm(1.6").

Previous part numbers: GRB236, GRB235, FRC4679

Price: 9.55 (11.46 Including VAT at 20%)



Clutch Release Bearing - S3 type
Clutch Release Bearing Ref: FTC5200=
Application: Series 3, Defender, Discovery 1 and Range Rover Classic.
Description: Latest design self centering release bearing by NSK. Standard equipment on Defender and Discovery 1, can be used on Series 3 and Range Rover Classic.

Price: 15.00 (18.00 Including VAT at 20%)



Clutch Release Bearing
Clutch Release Arm Ref: 576137
Application: Series 3, Defender V8 and TD5, Range Rover Classic V8, Discovery 1 V8 and Discovery 2 TD5.

Description: Cast steel clutch release arm.

Approximate dimensions: Overall length 21.2cm(8.3").

Price: 28.68 (34.42 Including VAT at 20%)



Clutch Release Arm
Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Clutch Parts for Land Rover Series 2 and 3
Page:  1  2  3   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Piston Assembly 2.4TDCI

Piston Assembly 2.4TDCI

122.63

Application: Defender from 2007 to 2012 with 2.4 litre TDCI engine.

Description: Standard size piston for 89.90mm bore. Supplied with rings, gudgeon pin and circlips. Made by Nural a Federal Mogul company.



find out more

Electric Fuel Pump - Series 1

Electric Fuel Pump - Series 1

100.44

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Repair Kit for Handbrake Adjuster

Repair Kit for Handbrake Adjuster

4.45

Application: Series 2A and Series 3.

Description: Old stock Lucas Girling repair kit for handbrake adjuster. Includes adjusting screw and wedges plus period tube of brake grease.


find out more

Injector for BMW M57 Diesel Engine

Injector for BMW M57 Diesel Engine

183.77

Application: Range Rover L322 with BMW M57 3.0litre diesel engine.

Description: Reconditioned Bosch injector for the M57 engine. Outright purchase, we do not need your old injector in vexchange.

Approximate dimensions: Overall length 22cm(8.7").

find out more

Bearing and Seals kit for Freelander 1 IRD

Bearing and Seals kit for Freelander 1 IRD

72.54

Application: Freelander 1 IRD unit except V6 model.

Description: Set of 7 OE spec bearings and 4 seals to overhaul the intermediate reduction drive unit. This kit does not include the plate for the oil cooler.

find out more

Rear Diff Repair Kit - Freelander2

Rear Diff Repair Kit - Freelander2

103.14

Application: Freelander 2 and Evoque

Description: Repair kit of OE bearings and seals for the rear differential. Kit includes 4x taper roller bearings, 3x oil seals, 2x 'O' rings, collapsible spacer and pinion nut.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -