Digital Dispensary

Product Sections


Best Sellers

Gasket Set for Solex 32PBI-2 Carburettor

Gasket Set for Solex 32PBI-2 Carburettor

7.66

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.
Description: Set of 6 gaskets and 8 fibre washers for this carburettor
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Differential Pinion

Oil Seal Differential Pinion

5.21

Application: Series 1, 2 & 3 Rover type differentials.

Description: Oil seal to nose of differential. Corteco/Gaco boxed.

Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").

Original part number: 217507.
find out more

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Gasket for Differential to Axle Casing

Gasket for Differential to Axle Casing

0.60

Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > DEFENDER Parts > Defender Engine Parts > 2.5 Diesels Naturally Aspirated and Turbo
Page:  1  2   >   >>
Oil Seal between Crankshaft and Front Cover Ref: ERR6490
Application: S1 1600 & 2000 petrol, 2ltr diesel, Series 2 & 3 4 and 6 cylinder engines, 200Tdi and 300TDi.
Description: Oil seal by Corteco for engine front cover.
Approximate dimensions: outside diameter 63.5mm (2.5"), thickness 10mm (3/8").
Original part number 213744.

Price: 3.65 (4.38 Including VAT at 20%)




People who bought this item also bought:
1. Timing Chain - AE boxed (Ref: ETC4499)
2. Inlet Valve (Ref: 233427)
3. Spigot Bush (Ref: LFB500050)
Oil Seal between Crankshaft and Front Cover
Rear Main Oil Seal on Crankshaft Ref: ERR2532
Application: Series 3 4cyl 5 main bearing engines, Defender 2.25 petrol, 2.5 petrol, 2.5 diesel, 2.5 turbo diesel and 200TDi.

Description: Genuine rear main oilseal supplied with guide sleeve for ease of fitting.

Approximate dimensions: Outside diameter 120mm(4.72"), inside diameter 98mm(3.86"), thickness 12mm(0.47").

Previous part number ERR1535.

Price: 29.90 (35.88 Including VAT at 20%)



Rear Main Oil Seal on Crankshaft
Thrust Washer Pair - Standard Size Ref: RTC2825
Application: Series 2A & Series 3 4 cylinder engines, Defender 2.25P, 2.5P, 2.5NAD and 2.5TD, 200TDI and 300TDI.

Description: Replacement pair of thrust washers for crankshaft - standard size. Usually fitted when crankshaft main journal bearings are replaced.

Approximate dimensions: Outside diameter of pair 86mm( 3.39"), inside diameter of pair 71mm(2.8"), thickness 2.36mm(0.093")

Previous part number: 538130

Price: 2.00 (2.40 Including VAT at 20%)



Thrust Washer Pair - Standard Size
Thrust Washer Pair - 0.0025" Oversize Ref: 538131
Application: Series 2A & Series 3 4 cylinder engines, Defender 2.25P, 2.5P, 2.5NAD and 2.5TD, 200TDI and 300TDI.

Description: Replacement pair of thrust washers for crankshaft0.0025" oversize. Usually fitted when crankshaft main journal bearings are replaced.

Approximate dimensions: Outside diameter of pair 86mm( 3.39"), inside diameter of pair 71mm(2.8"), thickness 2.43mm(0.0955")

Price: 2.00 (2.40 Including VAT at 20%)



Thrust Washer Pair - 0.0025
Thrust Washer Pair - 0.005" Oversize Ref: 538132
Application: Series 2A & Series 3 4 cylinder engines, Defender 2.25P, 2.5P, 2.5NAD and 2.5TD, 200TDI and 300TDI.

Description: Replacement pair of thrust washers for crankshaft0.005" oversize. Usually fitted when crankshaft main journal bearings are replaced.

Approximate dimensions: Outside diameter of pair 86mm( 3.39"), inside diameter of pair 71mm(2.8"), thickness 2.49mm(0.098")

Price: 2.00 (2.40 Including VAT at 20%)



Thrust Washer Pair - 0.005
Thrust Washer Pair - 0.0075" Oversize Ref: 538133
Application: Series 2A & Series 3 4 cylinder engines, Defender 2.25P, 2.5P, 2.5NAD and 2.5TD, 200TDI and 300TDI.

Description: Replacement pair of thrust washers for crankshaft0.0075" oversize. Usually fitted when crankshaft main journal bearings are replaced.

Approximate dimensions: Outside diameter of pair 86mm( 3.39"), inside diameter of pair 71mm(2.8"), thickness 2.43mm(0.1005")


Price: 2.00 (2.40 Including VAT at 20%)



Thrust Washer Pair - 0.0075
Thrust Washer Pair - 0.010" Oversize Ref: 538134
Application: Series 2A & Series 3 4 cylinder engines, Defender 2.25P, 2.5P, 2.5NAD and 2.5TD, 200TDI and 300TDI.

Description: Replacement pair of thrust washers for crankshaft0.010" oversize. Usually fitted when crankshaft main journal bearings are replaced.

Approximate dimensions: Outside diameter of pair 86mm( 3.39"), inside diameter of pair 71mm(2.8"), thickness 2.62mm(0.103")

Price: 2.00 (2.40 Including VAT at 20%)



Thrust Washer Pair - 0.010
Camshaft Bearing - Front Ref: ETC8442
Application: Series 2A & Series 3 4 cylinder engines, Defender 2.25P, 2.5P, 2.5NAD and 2.5TD, 200TDI and 300TDI.

Description: Replacement front bearing for camshaft. This is not a 'DIY' job to fit, this needs an engine machine shop.

Approximate dimensions: Outside diameter 50.2mm( 1.98"), inside diameter 46.5mm(1.83"), length 24.7mm(0.97")

Previous part number: 90519054

Price: 3.50 (4.20 Including VAT at 20%)



Camshaft Bearing - Front
Camshaft bearing Ref: 90519055
Application: Series 2A & Series 3 4 cylinder engines, Defender 2.25P, 2.5P, 2.5NAD and 2.5TD, 200TDI and 300TDI.

Description: Replacement bearing for camshaft, 3 fitted per engine. This is not a 'DIY' job to fit, this needs an engine machine shop. Usually fitted at same time as front camshaft bearing.

Approximate dimensions: Outside diameter 50.2mm( 1.98"), inside diameter 46.5mm(1.83"), length 19mm(0.75")

Price: 1.88 (2.26 Including VAT at 20%)



Camshaft bearing
Banjo Bolt for Oil Feed Pipe Ref: ETC4498
Application: Late Series3 4 cylinder petrol and diesel engines with metric fixings (from approx 1980). Defender with 2.25 petrol, 2.5 petrol, 2.5 diesel and 2.5 turbo diesel.

Description: Banjo bolt for both ends of the oil feed pipe that delivers lubricating oil to cylinder head from cylinder block.

Approcimate dimensions: Head is 17mm(0.7") across flats, overall length 32mm(1.26"), thread is M10.

Price: 0.95 (1.14 Including VAT at 20%)



Banjo Bolt for Oil Feed Pipe
Digital Dispensary > DEFENDER Parts > Defender Engine Parts > 2.5 Diesels Naturally Aspirated and Turbo
Page:  1  2   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Outer Pinion Bearing

Outer Pinion Bearing

10.72

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for outer end of differential pinion gear. Timken bearing numbers HM88046/HM88010

Approximate dimensions: Outside diameter 2.7"(68.5mm), inside diameter 1.25"(31.8mm)., height 0.93"(23.5mm).


find out more

Inner Pinion Bearing - Differential

Inner Pinion Bearing - Differential

21.70

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for inner end of differential pinion gear. Timken bearing numbers HM801346X/HM801310

Approximate dimensions: Outside diameter 3.25"(82.5mm), inside diameter 1.5"(38mm)., height 1.22"(31mm).

find out more

Seal Kir for 1 1/8" Wheel Cylinders

Seal Kir for 1 1/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for rear wheel cylinders with bore of 1 1/8"(28.5mm). Kit has sufficient seals for both front wheel cylinders.

find out more

Seal Kit for 1 3/8" Wheel Cylinders

Seal Kit for 1 3/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for front wheel cyliders with bore of 1 3/8"(35mm). Kit has sufficient seals for both front wheel cylinders.


find out more

Outlet Nozzle - SU Fuel Pump

Outlet Nozzle - SU Fuel Pump

4.44

Application: Series 1 and early Series 2 models.

Description: Nozzle for outlet of SU fuel pumps. Allows push-on fuel hose connection to pump.

Approximate dimensions: Thread diameter 22mm(0.87"), nozzle diameter 7mm(0.28").

find out more

Wiper Arm Series 3 RH

Wiper Arm Series 3 RH

24.25

Application: Series3 models.

Description: Right hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -