Digital Dispensary

Product Sections


Best Sellers

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Gasket Set for Series Gearboxes

Gasket Set for Series Gearboxes

4.20

Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more

Water Pump Series1 Petrol

Water Pump Series1 Petrol

51.00

Application: Series 1 1.6ltr & 2.0ltr petrol (gasolene) engines.

Description: Reproduction cast iron water pump, supplied with gaskets.
find out more

Gaiter for High/Low Gear Lever

Gaiter for High/Low Gear Lever

2.46

Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

13.70

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Wheel Stud for Series 1

Wheel Stud for Series 1

5.82

Application: All Series One models.

Description: Reproduction wheel stud for Series 1. Threaded 9/16"BSF. Use with nut 217361.

Approximate dimensions: Overall length 52mm(2"), short threaded end 12mm(0.47"), long threaded end 27.5mm(1.08"), land 12.5mm(0.5")

find out more

These Superb Prices are ONLY available when you order ON-LINE

Page:   <<   <  1  2  3  4  5  ...   >   >>
Installer Axle Shaft Seal Ref: 205-863
Application: Freelander 2 (LR 2) and Evoque.

Description: Installer for half-shaft seal.

Approximate dimensions: Overall length 31cm(12.2"), overall diameter 74mm(2.9").

Price: 71.65 (85.98 Including VAT at 20%)



Installer Axle Shaft Seal
Installer Pinion Oil Seal Ref: JLR-205-865
Application: Freelander 2 and Evoque.

Description: Installer for the pinion oil seal of the rear differential. Use with 307-520 handle/striker shaft..

Approximate dimensions: Overall diameter 92mm(3.62"), internal diameter 28mm(1.1"), lrngth 35mm(1.38").

Price: 47.88 (57.46 Including VAT at 20%)



Installer Pinion Oil Seal
Differential Support Bracket Ref: JLR-205-972
Application: Freelander 2.

Description: Bracket assembly for supporting rear differential whilst under repair. Kit includes main bracket, supplementary bracket and 8 bolts.

Approximate dimensions: Main bracket 33.5cm(13.2"), x 19cm(7.5") x 17cm(6.7"). Small bracket 10cm(4") x 6cm(2.4") x 2.5cm(1").


Price: 127.11 (152.53 Including VAT at 20%)



Differential Support Bracket
Pinion Flange Remover-Replacer Ref: JLR-205-984
Application:Freelander 2, 2006 onwards.
Description: Two part tool for removing and replacing pinion drive flange on rear differential.
Approximate dimensions: Inner tool - 160mm( 6.3") long, 3/4"(19mm) socket drive, fine spline(24) 24mm(0.95") overall diameter. Outer tool - 150mm(5.9") long, with 135mm(5.3") reaction arm. double hex(12point) socket 41mmAF

Price: 151.48 (181.78 Including VAT at 20%)



Pinion Flange Remover-Replacer
Installer Bearing and Seal Rear Differential Ref: JLR-205-986
Application: Freelander 2.

Description: Installation tool for bearing and seal to rear differential pinion.

Approximate dimensions: Main body overall length 14.7cm(5.8"), main diameter 45mm(1.8"), collar diameter 62mm(2.45").. Black plastic adaptor overall diameter 95mm(3.74"), step 63mm(2.5")

Price: 76.00 (91.20 Including VAT at 20%)



Installer Bearing and Seal  Rear Differential
Adaptor Kit to remove Injection Pump Ref: 303-249-01
Application: Defender 2010 to 2016 with Puma TDCi engine.

Description: Adaptor kit for use with remover tool 303-249. To remove sprocket from injection pump on later versions where sprocket does not have threaded holes.

Approximate dimensions: Arms 68mm(2.7") long. Adator post for centre force screw 42mm(1.65") long.

Price: 58.67 (70.40 Including VAT at 20%)



Adaptor Kit to remove Injection Pump
Shim - Cam Timing Tool Ref: 303-530-04
Application: Range Rover Sport, Range Rover l322 and Discovery 3 where fitted with 4.4 litre V8 petrol engine.
Description: Shim 0.25mm thick for use with cam timing tool.
Approximate dimensions: Overall length 138mm(5.4"), width 20mm(0.8"), thickness 0.25mm(0.010")

Price: 18.72 (22.46 Including VAT at 20%)



Shim - Cam Timing Tool
Crank Timing Pin Ref: 303-645A
Application: Range Rover Sport, Range Rover l322 and Discovery 3 where fitted with 4.4 litre V8 petrol engine.
Description: Crankshaft timing pin.
Approximate dimensions: overall length 36.4mm(1.4")

Price: 43.98 (52.78 Including VAT at 20%)



Crank Timing Pin
Remover Inspection Plate Ref: 303-679A
Application: Defender 2007>2016 with Ford Puma TDCi engine.

Description: Tool to remove inspection plate to front of engine. 3 pegs engage with plate and then tool is rotated using 1/2" drive socketry.

Approximate dimensions:Overall diameter 10cm(4"),

Price: 25.20 (30.24 Including VAT at 20%)



Remover Inspection Plate
Aligner for Oil Pump Defender 2007 onwards Ref: 303-705
Application: Defender 2007 with the Ford Puma engine.

Description: Tool for aligning the engine oil pump on installation.

Approximate dimensions: 120mm(4.72") x 50mm(1.97") x 2mm(0.08")

Price: 15.47 (18.56 Including VAT at 20%)



Aligner for Oil Pump Defender 2007 onwards
Page:   <<   <  1  2  3  4  5  ...   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Steering Arm - Series 1

Steering Arm - Series 1

17.82

Application: Series 1 models 1948 to 1956 approx.

Description: Drop arm for early type steering box. This arm is held in place with a pinch bolt.

Approximate dimensions: Overall length 17.4cm(6.9")

find out more

'D' Washer - Pedal Shaft

'D' Washer - Pedal Shaft

0.96

Application: Series 1 models.

Description: 'D' washer for support shaft for brake and clutch pedals.

Approximate dimensions: Outside diameter 38mm(1.5"), thickness 3mm(1/8").


find out more

Fixing Kit for Manifolds - Metric

Fixing Kit for Manifolds - Metric

12.83

Application: Series 3 from 1980 with 2.25 litre petrol engine.

Description: Metric threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Fixing Kit for Manifolds - Imperial

Fixing Kit for Manifolds - Imperial

10.20

Application: Series 2 and Series 3 to approx 1980 with 2.25 litre petrol engine.

Description: Imperial (inch) threaded kit of fixings to hold manifolds to cylinder head. Kit includes 6 bolts, 2 set screws, 3 studs, 9 plain washers, 11 lock washers, 3 nuts, 2 clamps and 2 lockers

find out more

Shackle Plate Rear

Shackle Plate Rear

11.16

Application: Series1 1948 to 1953.

Description: Shackle plate for rear springs with plain 9/16" diameter holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")
find out more

Shackle Plate Rear

Shackle Plate Rear

13.02

Application: Series 1 1948 to 1953.

Description: Shackle plate for rear springs with 1/2"BSF threaded holes.

Approximate dimensions: Length 113mm(4.45"), width 38mm(1.5"), thickness 9.2mm(0.36")

find out more

Clip for 3/16" Brake Pipe

Clip for 3/16

1.39

Application: Series1, Series2/2A and Series3 models.

Description: Reproduction stainless steel clip for brake pipes. Intended for 3/16" pipe, but will work with 1/4" diameter pipe also.

Approximate dimensions: Length 20mm(0.8"), width 10mm(3/8"), height 5mm(0.2"), hole diameter 4mm(0.16").

find out more

Rear End-plate for Cylinder Head

Rear End-plate for Cylinder Head

97.66

Application: Series 1 petrol models 1948 to 1958, Series 2 models with 2 litre petrol engine.

Description: Reproduction end plate in cast aluminium with mounting aperature for thermo switch.

Approximate dimensions: Length 91mm(3.6"), height 84mm(3.3"), depth 18.4mm(0.72")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -