Digital Dispensary

Product Sections


Best Sellers

Gasket Set for Solex 32PBI-2 Carburettor

Gasket Set for Solex 32PBI-2 Carburettor

7.66

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.
Description: Set of 6 gaskets and 8 fibre washers for this carburettor
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Differential Pinion

Oil Seal Differential Pinion

5.21

Application: Series 1, 2 & 3 Rover type differentials.

Description: Oil seal to nose of differential. Corteco/Gaco boxed.

Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").

Original part number: 217507.
find out more

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Gasket for Differential to Axle Casing

Gasket for Differential to Axle Casing

0.60

Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > SPECIAL Tools for Land Rover > Other Tools for Land Rovers
Page:  1  2  3  4   >   >>
Extended Socket for Prop Shaft Nuts Ref: ZZDA1065
Application: Series 1, Series 2/2A, Series 3, Defender, Discovery 1, Discovery 2, Range Rover Classic and Range Rover 38A.
Description: 3/8" drive extended 6 point socket for prop shaft nuts and bolts. Specially necked body (10mm diameter) to clear universal joints and thin wall socket. Size 9/16"AF. Use in conjunction with ZZBRIRJ562A combination spanner.
Overall length 15cm ( 5.9")

Price: 16.60 (19.92 Including VAT at 20%)



Extended Socket for Prop Shaft Nuts
Spanner for propshaft nuts and bolts Ref: ZZBRIRJ562A
9/16" A/F combination spanner by BRITOOL. The correct size for propshaft nuts and bolts. A quality spanner that provides a good tight grip on those propshaft nuts and bolts, but is slim enough to fit inside the propshaft flanges.
You need two of these to do the job. Or one if used with extended socket above.
Approximate dimensions: overall length 190mm.

Price: 7.88 (9.46 Including VAT at 20%)



Spanner for propshaft nuts and bolts
Double Hex Socket for Caliper Bolts Ref: ZZBETA910L13M
Application: Defender and Discovery 1 from approx1994 with caliper fixing bolts of the double hex (12 point) type.
Description: 3/8" drive 13mm double hex (12 point) socket. Length 55mm.

Price: 6.50 (7.80 Including VAT at 20%)



Double Hex Socket for Caliper Bolts
Pipe Bending Tool Ref: ZZOAK000160
Application: 3/16" outside diameter brake pipe.

Description: Pipe bending tool by Oakes. For neat small radius bends in 3/16" diameter brake pipe. Useful for copper pipe, almost essential for copper-nickel or steel pipes.

Approximate dimesions: Overall length 14cm(5.5"), width 6cm(2.4").

Price: 14.02 (16.82 Including VAT at 20%)



Pipe Bending Tool
Drop Arm Puller by Sykes-Pickavant Ref: ZZSP050500
Application: Range Rover Classic, Defender, Discovery1 and Transit.

Description: Drop arm puller by Sykes Pickavant, a cheaper alternative to the Bushwacker version. Gap between jaws 40mm, max opening 44mm.

Price: 195.00 (234.00 Including VAT at 20%)



Drop Arm Puller by Sykes-Pickavant
Mixture Adjusting Tool for CD175 Carburetter Ref: ZZB20379
Application: Range Rover Classic.
Description: This tool is for top adjust type carbs with the "Allen" key adjusting screw. After removal of the damper unit from the carburetter top, the tool is inserted into the damper reservoir. The central allen key locates in a socket in the reservoir base, whilst the outer barrel locks into the the air valve guide slot. Rotating the allen key clockwise will lower the needle to weken the mixture, rotating it anti-clockwise will raise the needle and richen the mixture. The location of the outer barrel is important in order to prevent the air valve from rootating whilst the adjustment is being carried out, otherwise the main diaphragm may be damaged.

Price: 12.25 (14.70 Including VAT at 20%)



Mixture Adjusting Tool for CD175 Carburetter
Mixture Adjusting Tool CD175 Ref: ZZB25860
Application: Range Rover Classic, Discovery 1, Series3 109V8 and Defenders where fitted with twin Stromberg CD175 carburetters.
Description: This tool is for top adjust type carbs with the raised blade adjusting screw used from 1977. After removal of the damper unit from the carburetter top, the tool is inserted into the damper reservoir. The head of the tool locates onto the raised blade, whilst the outer barrel locks into the the air valve guide slot. Rotating the allen key clockwise will lower the needle to weken the mixture, rotating it anti-clockwise will raise the needle and richen the mixture. The location of the outer barrel is important in order to prevent the air valve from rootating whilst the adjustment is being carried out, otherwise the main diaphragm may be damaged.

Sorry, temporarily out of stock.

Price: 16.10 (19.32 Including VAT at 20%)



Mixture Adjusting Tool CD175
Carburettor Balancer Ref: ZZPEN386-200
Description: For syncronizing multiple carburettor engines. Works with side draught, downdraught and anything in between. Supplied with instructions.

Approximate dimensions: Outside diameter of suction head 75mm(3")

Price: 28.28 (33.94 Including VAT at 20%)



Carburettor Balancer
Rivet Set - 3/16" Ref: ZZ489
Application: Series 1, Series2 and Series 3.

Description: Made from heat treated tool steel in UK this tool is used to set up and then form head on solid 3/16" diameter solid aluminium rivets used on bodywork.

Approximate dimensions: Overall length 126mm(5")

Back in stock

Price: 14.14 (16.97 Including VAT at 20%)




People who bought this item also bought:
1. Solid Aluminium Rivets - 3/8" long - bag of 50 (Ref: 300789X50)
2. Gasket Water Branch to Cylinder Head (Ref: 210447)
3. Solid Aluminium Rivets - 7/16" long - bag of 50 (Ref: 300783X50)
Rivet Set - 3/16
Wrench Oil Filter TD5 Ref: ZZDA1117
Application: Defender and Discovery 2 with TD5 engine.
Description: Wrench for removing and fitting the oil filter on the TD5 engine. Access is limited on this engine and this tool makes the tightening and removal of the filter easier.
Approximate dimensions: Head ovweall diameter 86mm(3.4"), overall length 205mm(8.1")

Price: 10.57 (12.68 Including VAT at 20%)



Wrench Oil Filter TD5
Digital Dispensary > SPECIAL Tools for Land Rover > Other Tools for Land Rovers
Page:  1  2  3  4   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Outer Pinion Bearing

Outer Pinion Bearing

10.72

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for outer end of differential pinion gear. Timken bearing numbers HM88046/HM88010

Approximate dimensions: Outside diameter 2.7"(68.5mm), inside diameter 1.25"(31.8mm)., height 0.93"(23.5mm).


find out more

Inner Pinion Bearing - Differential

Inner Pinion Bearing - Differential

21.70

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for inner end of differential pinion gear. Timken bearing numbers HM801346X/HM801310

Approximate dimensions: Outside diameter 3.25"(82.5mm), inside diameter 1.5"(38mm)., height 1.22"(31mm).

find out more

Seal Kir for 1 1/8" Wheel Cylinders

Seal Kir for 1 1/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for rear wheel cylinders with bore of 1 1/8"(28.5mm). Kit has sufficient seals for both front wheel cylinders.

find out more

Seal Kit for 1 3/8" Wheel Cylinders

Seal Kit for 1 3/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for front wheel cyliders with bore of 1 3/8"(35mm). Kit has sufficient seals for both front wheel cylinders.


find out more

Outlet Nozzle - SU Fuel Pump

Outlet Nozzle - SU Fuel Pump

4.44

Application: Series 1 and early Series 2 models.

Description: Nozzle for outlet of SU fuel pumps. Allows push-on fuel hose connection to pump.

Approximate dimensions: Thread diameter 22mm(0.87"), nozzle diameter 7mm(0.28").

find out more

Wiper Arm Series 3 RH

Wiper Arm Series 3 RH

24.25

Application: Series3 models.

Description: Right hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -