Digital Dispensary

Product Sections


Best Sellers

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Seal Kit for Brake Master Cylinder

Seal Kit for Brake Master Cylinder

19.80

Application: Series One from 1948 to 1958.
Description: Reproduction seal kit for brake master cylinder. Suits all short wheel base models. Not suitable for long wheel base models.
Original part number 278524
find out more

Anchor Plate for 10inch brake shoes

Anchor Plate for 10inch brake shoes

8.44

Anchor plate for use with 10inch brakes - see kit above. One anchor plate is used with each pair of shoes. These do not need replacing with every change of brake shoes, but they do become worn over several years use. Sold singly.
Approximate dimensions: 78mm x 45mm x 5mm.

Application: see STC2796DKIT above.
find out more

Felt Seal Stub Shaft to Drive Flange

Felt Seal Stub Shaft to Drive Flange

0.48

Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Split Pin - Shocker Retention

Split Pin - Shocker Retention

0.25

Application: Series 1, Series 2 and Series 3.

Description: Replacement split pin for retaining shock absorber to bottom plate of spring.

Approximate dimensions: Overall length 55.5mm(2.2"), diameter 6mm(0.24")

find out more

Dust Cap for Bleed Screw

Dust Cap for Bleed Screw

0.30

Application: Suitable for all bleed screws.
Description: Soft plastic dust cap for bleed screws.
Approximate dimensions: length 15mm(0.6"), diameter 8mm (0.3")
Original part number 234957
find out more

Screw for retaining Brake Drums

Screw for retaining Brake Drums

0.25

Application: Series 1, 2 & 3.
Description: Countersunk head screw 3/8"BSW by 5/8" long.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Suspension Parts for Land Rover Series 2 and 3
Page:  1  2  3  4   >   >>
Spring Bush for 2.5" wide Springs Ref: 548205
Application Series 1, 2 & 3.
Description: Original 'Clayflex' spring bushes. Suitable for all 2.5"(63.5mm) wide springs.
Approximate dimensions: overall length 70mm (2.75"), inside diameter 9/16"(14.3mm). outside diameter 30.2mm(1 3/16")

Price: 2.05 (2.46 Including VAT at 20%)




People who bought this item also bought:
1. Oil Seal Set for Gearbox (Ref: 600603KIT)
2. Yellow Knob - 4WD Gear lever (Ref: 232813)
3. Axle Bump Rubber (Ref: 241380)
Spring Bush for 2.5
Repacement Spring Bush for 2.5" wide Springs Ref: 548205D
Application Series 1, 2 & 3.
Description: Replacement spring bushes. Suitable for all 2.5"(63.5mm) wide springs.
Approximate dimensions: overall length 70mm (2.75"), inside diameter 9/16"(14.3mm). outside diameter 30.2mm(1 3/16")

Price: 0.80 (0.96 Including VAT at 20%)



Repacement Spring Bush for 2.5
Replacement Suspension Bush Ref: 569746D
Application: Series 2A models both 88" and 109" wheelbases and Series 3 88" only.

Description: Replacement metalastic suspension bush in chassis for rear of front spring.

Approximate dimensions: Overall length 91.8mm(3.6"), outside diameter 30mm(1.2"), inside diameter 9/16"(14.3mm).

Price: 2.05 (2.46 Including VAT at 20%)



Replacement Suspension Bush
Replacement Suspnsion Bush Ref: 90577434D
Application: Series 3 109.

Description: Replacement metalastic bush. Fitted in chassis at rear of front spring.

Approximate dimensions: Overall length 92mm(3 5/8"), outside diameter 38.2mm(1.5"), internal diameter 9/16"(14.3mm).

Price: 2.80 (3.36 Including VAT at 20%)




People who bought this item also bought:
1. Rear Shock Absorber (Ref: RTC4442D)
2. Split Pin - Shocker Retention (Ref: 4063A)
3. Barrel and 2 Keys (Ref: 320609)
Replacement Suspnsion Bush
Full set Ser1, Ser2 and SWB Ser3 Ref: ZZPOLYDYNASET04
Full Set of Polybush covers the spring end bushes plus the chassis bushes for springs.

Application: Series 1 (except early narrow leaf types), Series 2 & 2A, short wheel base Series3.

Available only in Dynamic Formula.

Price: 94.66 (113.59 Including VAT at 20%)



Full set Ser1, Ser2 and SWB Ser3
Full Set for LWB Series3. Ref: ZZPOLYDYNASET05
Full Set of Polybush covers the spring end bushes plus the chassis bushes for springs.
Application: Series 3 long wheel base.
Available in only in Dynamic Formula.

Price: 94.66 (113.59 Including VAT at 20%)



Full Set for LWB Series3.
Fixings kit for Set04 and Set05 Ref: ZZPOLYDYNASET04FIX
The set of nuts, bolts and washers for fitting Polybush Set03.

Lets you do a 'complete' job when fitting your new Polybush set. Rather than using tired and worn fixings, this set compliments the Polybushes with exact fit new fixings to give you complete peace of mind.

This set is also suitable for the original bushes.

Application: Ser1, Ser2, Ser2A and Ser3.

Price: 12.04 (14.45 Including VAT at 20%)



Fixings kit for Set04 and Set05
Shackle Plate 109 Front Ref: 90577721A
Application: Series 2A and Series 3 109"(LWB) models.

Description: Reproduction inner shackle plate for front springs. This is the plate with 9/16"UNF threaded holes. There is also an 'upstand' (or spacer) around one hole.

Approximate dimensions: Overall length 140mm(5.5"), width 40mm(1.6"), thickness 10mm(0.4"), upstasnd 16.2mm(0.65"). Holes centre to centre 4 1/8"(104.8mm).

Price: 2.20 (2.64 Including VAT at 20%)




People who bought this item also bought:
1. Shackle Plate 109 Front (Ref: 90577723A)
2. Split Pin - Shocker Retention (Ref: 4063A)
3. Shackle Plate 109 Rear (Ref: 279970)
Shackle Plate 109 Front
Shackle Plate 109 Front Ref: 90577723A
Application: Series 2A and Series 3 109"(LWB) models.

Description: Reproduction outer shackle plate for front springs. This is the plate with plain 9/16" diameter holes.

Approximate dimensions: Overall length 140mm(5.5"), width 40mm(1.6"), thickness 10mm(0.4"). Holes centre to centre 4 1/8"(104.8mm).

Price: 2.00 (2.40 Including VAT at 20%)




People who bought this item also bought:
1. Shackle Plate 109 Front (Ref: 90577721A)
2. Split Pin - Shocker Retention (Ref: 4063A)
3. Shackle Plate 109 Rear (Ref: 279970)
Shackle Plate 109 Front
Shackle Plate 109 1Ton Front Ref: 90577716
Application: Standard fit to 109 1Ton, optional fit to other models where larger wheels fitted or additional ground clearance required.

Description: Replacement threaded inner shackle plate. Top and bottom holes threaded 9/16"UNF. Middle hole drilled 13.4mm(0.53").

Approximate dimensions: Overall length 178mm(7"), width 40.5mm(1.6"), thickness 10.6mm(0.42").

Price: 8.41 (10.09 Including VAT at 20%)



Shackle Plate 109 1Ton Front
Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Suspension Parts for Land Rover Series 2 and 3
Page:  1  2  3  4   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Piston Assembly 2.4TDCI

Piston Assembly 2.4TDCI

122.63

Application: Defender from 2007 to 2012 with 2.4 litre TDCI engine.

Description: Standard size piston for 89.90mm bore. Supplied with rings, gudgeon pin and circlips. Made by Nural a Federal Mogul company.



find out more

Electric Fuel Pump - Series 1

Electric Fuel Pump - Series 1

100.44

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Repair Kit for Handbrake Adjuster

Repair Kit for Handbrake Adjuster

4.45

Application: Series 2A and Series 3.

Description: Old stock Lucas Girling repair kit for handbrake adjuster. Includes adjusting screw and wedges plus period tube of brake grease.


find out more

Injector for BMW M57 Diesel Engine

Injector for BMW M57 Diesel Engine

183.77

Application: Range Rover L322 with BMW M57 3.0litre diesel engine.

Description: Reconditioned Bosch injector for the M57 engine. Outright purchase, we do not need your old injector in vexchange.

Approximate dimensions: Overall length 22cm(8.7").

find out more

Bearing and Seals kit for Freelander 1 IRD

Bearing and Seals kit for Freelander 1 IRD

72.54

Application: Freelander 1 IRD unit except V6 model.

Description: Set of 7 OE spec bearings and 4 seals to overhaul the intermediate reduction drive unit. This kit does not include the plate for the oil cooler.

find out more

Rear Diff Repair Kit - Freelander2

Rear Diff Repair Kit - Freelander2

103.14

Application: Freelander 2 and Evoque

Description: Repair kit of OE bearings and seals for the rear differential. Kit includes 4x taper roller bearings, 3x oil seals, 2x 'O' rings, collapsible spacer and pinion nut.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -