Digital Dispensary

Product Sections


Best Sellers

'O' Ring for Thermostat

'O' Ring for Thermostat

0.55

Application: Series 1, 2 & 3 4cylinder engines.
Description: 'O' ring for sealing thermostat to cylinder head.
Approximate dimensions: outside diameter 55mm (2.2").
Original part number 01645
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Thermostat 82 degrees

Thermostat 82 degrees

10.61

Application: Series 1 1.6ltr & 2.0ltr petrol engines, Defender 2.5 & 2.5TD diesel engines.

Description: Waxstat 82degree thermostat.

Original part number: 504560.

find out more

Gasket Exhaust Manifold to Down Pipe

Gasket Exhaust Manifold to Down Pipe

0.96

Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Brass Nut 5/16"BSF

Brass Nut 5/16

1.66

Application: Series1 exhaust manifold.

Description: Brass nut 5/16"BSF for holding downpipe to exhaust manifold.

Approximate dimensions: 3/8"(9.5mm) high, 17/32"(13.5mm) across flats.

find out more

Fixings Kit for Water Pump

Fixings Kit for Water Pump

19.87

Application: Series One, 1948 to 1958.

Description: Set of fixings for water pump comprising the following parts;
6x 250517 bolt 1/4"BSF x 1.5", 1x 250518 bolt 1/4"BSF x 1.75", 1x 237150 bolt 1/4"BSF x 2.25", 2x set screw 5/16"BSW x 11/16" plus 8x 1/4" lock washers and 2x 5/16" lock washers.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Brake Parts
Page:   <<   <  1  2  3  4  5   >   >>
Bush for Relay Shaft Ref: 90218014
Application: Series1.

Description: Reproduction bronze bush for relay shaft of cluctch linkage on RHD models.

Approximate dimensions: Collar outside diameter 33.5mm(1.32"), body outer diameter 28.7mm(1.13"), internal diameter 24mm(0.95"), overall length 25mm(1").
Old part number: 218014


Price: 27.55 (33.06 Including VAT at 20%)



Bush for Relay Shaft
Seal Kit for Brake Master Cylinder Ref: ZZSP1975-5
Application: Series One from 1948 to 1958.
Description: Reproduction seal kit for brake master cylinder. Suits all short wheel base models. Not suitable for long wheel base models.
Original part number 278524

Price: 16.50 (19.80 Including VAT at 20%)




People who bought this item also bought:
1. Brake Hose (Ref: 219824KIT)
2. 80" Brake Pipe Set LHD (Ref: ZZGL5600)
3. Return Spring - Leading Shoe 10" (Ref: 503981)


Related products:
1. Cylinder Hones - Brakes (Ref: ZZLAS2243)
2. 1litre Bottle of Silicon Brake Fluid (Ref: ZZDYNSILIDOT5)
Seal Kit for Brake Master Cylinder
Seal Kit for Brake Master Cylinder 107/109 Ref: 278523
Application: Series One 107 and 109 models with 11" brake drums.
Description: Reproduction seal kit for brake master cylinder on long wheel base models. Kit may not include metalwork - depending on availability. This kit is for 1" bore cylinders.

Price: 18.00 (21.60 Including VAT at 20%)




People who bought this item also bought:
1. Series1, 2 & 3 Technical Publications on DVD (Ref: ZZLTP3001)
2. 1litre Bottle of Silicon Brake Fluid (Ref: ZZDYNSILIDOT5)
3. Washer Shock Absorber Bush (Ref: RYF500160)


Related products:
1. 1litre Bottle of Silicon Brake Fluid (Ref: ZZDYNSILIDOT5)
2. Cylinder Hones - Brakes (Ref: ZZLAS2243)
Seal Kit for Brake Master Cylinder 107/109
Reservoir for S1 Brakes Ref: 271581
Application: Series One 1948 to 1958.

Description: Reproduction steel brake fluid reservoir supplied with steel cap.

Approximate dimensions: Overall length 145mm(5.7"), overall diameter 68.5mm(2.7")

Back in stock.

Price: 32.40 (38.88 Including VAT at 20%)




People who bought this item also bought:
1. Seal Kit for Brake Master Cylinder (Ref: ZZSP1975-5)
2. 80" Brake Pipe Set LHD (Ref: ZZGL5600)
3. Shock Absorber 1948 - 1953 (Ref: 241037)


Related products:
1. 1litre Bottle of Silicon Brake Fluid (Ref: ZZDYNSILIDOT5)
Reservoir for S1 Brakes
Grommet Series 1 Pedals Ref: 70620
Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.

Price: 9.00 (10.80 Including VAT at 20%)




People who bought this item also bought:
1. Felt Seal for Series 1 Pedals (Ref: 70621)
2. Clevis for Hand Brake Linkage (Ref: 215809)
3. Steering Box Repair Kit (Ref: STRGBOXKIT01)
Grommet Series 1 Pedals
Felt Seal for Series 1 Pedals Ref: 70621
Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.

Price: 3.05 (3.66 Including VAT at 20%)




People who bought this item also bought:
1. Grommet Series 1 Pedals (Ref: 70620)
2. Axle Bump Rubber (Ref: 241380)
3. Clevis for Hand Brake Linkage (Ref: 215809)
Felt Seal for Series 1 Pedals
Brakelight Switch Ref: 7160
Application: Series One Land Rovers 1948 to 1958.

Description: Replacement pull-on type of brakelight switch. Please note that this is not a direct replacement and requires a little fettling to use.

Approximate dimensions: Mounting hole centres 26mm (1")

Price: 5.31 (6.37 Including VAT at 20%)




People who bought this item also bought:
1. Gasket Set for Series Gearboxes (Ref: 600603D)
2. Red Knob High/Low Gear Lever (Ref: 219521)
3. Yellow Knob - 4WD Gear lever (Ref: 232813)
Brakelight Switch
Clevis for Hand Brake Linkage Ref: 215809
Application: Series 1, 2 & 3.
Description: Reproduction clevis with pin for hand brake linkage. Threaded for 5/16"UNF rod.
Approximate dimensions: overall length 46mm (1.8")

Price: 3.05 (3.66 Including VAT at 20%)




People who bought this item also bought:
1. Felt Seal for Series 1 Pedals (Ref: 70621)
2. Grommet Series 1 Pedals (Ref: 70620)
3. Grommet - Brake Pipe Support (Ref: 6860L)
Clevis for Hand Brake Linkage
80" Brake Pipe Set RHD Ref: ZZGB5600
Application: Series 1 80" vehicles Right Hand Drive.
Description: Set of 1/4" diameter brake pipes in copper with brass unions by Automec. Seven pipes are included in this set. Comes with plastic pipe clips. Reservoir to master cylinder pipe is not included.

Price: 103.12 (123.74 Including VAT at 20%)




People who bought this item also bought:
1. Brass 'T' Piece for 1/4" Pipes (Ref: ZZHU34)
2. Tee Piece (Ref: BTB657L)
3. Felt Seal for Series 1 Pedals (Ref: 70621)
80
1litre Bottle of Silicon Brake Fluid Ref: ZZDYNSILIDOT5
Application: All Landrover models.

Description: Dynolite's performance silicone Dot5 (dot 5) Brake Fluid repels moisture so, unlike standard polyglycol brake fluid, it never needs changing. Rust and corrosion are inhibited because moisture is kept out of the system and the high boiling point of 260 degrees C is maintained throughout the life of the product therefore ensuring consistent, safe performance. Thanks to this, Dynolite silicone brake fluid lasts the lifetime of your vehicle, never needing to be changed. It will also not damage your paintwork if spilled and will not easily catch fire in the event of an accident. Pure silicone brake fluid will essentially eliminate wear snd corrosion in the hydraulic system.
It is ideal for use in vehicles that are only used occasionally where otherwise water absorbtion into the brake fluid is a major problem.

Price: 25.96 (31.15 Including VAT at 20%)




People who bought this item also bought:
1. Grommet - Brake Pipe Support (Ref: 6860L)
2. Screw for retaining Brake Drums (Ref: 1510)
3. Clip for brake pipe grommet (Ref: 56666)
1litre Bottle of Silicon Brake Fluid
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Brake Parts
Page:   <<   <  1  2  3  4  5   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Locking Hasp for Fuel Cap

Locking Hasp for Fuel Cap

4.50

Application: Series 2a and Series 3.

Description: Locking hasp for fuel cap with 'ears'. Allows use of padlock to secure fuel cap.

Approximate dimensions: Mounting screw centres 70mm(2.75")

Old part number: GLR361

find out more

Bail Assembly

Bail Assembly

2.70

Application: Series 2A and Series 3.

Description: Retainer for glass bowl on side of lift pump on 4 cylinder models.

Approximate dimensions: Overall length 92mm, width 58mm.

find out more

Fuel Filler Cap

Fuel Filler Cap

26.46

Application: Series 2a and Series 3.

Description: Old stock Unipart 2 lug fuel filler cap. Supplied with seal,

Approximate dimensions: Overa;; diameter 96mm(3.8").

find out more

6 Way Lighting Switch - Military

6 Way Lighting Switch - Military

153.60

Application: Series3, Light Weight, 101 and Defender military models.

Description: Old stock Lucas 34259 six way lighting swith with facility for lock barrel (not supplied).


find out more

Bypass Hose Series 1 1948-1953

Bypass Hose Series 1 1948-1953

8.70

Application: Series 1 1948 to 1953 with 1.6 litre and early 2 litre engines.

Description: Reproduction bypass hose.

Approximate dimensions: Overall length 88mm(3.5"), outside diameter 45mm(1.8"), inside diameter 34mm(1.3")

find out more

Engine Breather-Filter

Engine Breather-Filter

22.69

Application: Defender with 2.5litre naturally aspirated diesel engine.

Description: Breather cap on top of rocker cover with single pipe outlet of 19mm diameter.

find out more

Installer Oil Seal

Installer Oil Seal

131.21

Application: Freelander2 and Evoque.

Description: Installer for oil seal. Beleived to be on front differential.

Approximate dimensions: Overall length 19.4cm(7.6"), overall diameter 90mm(3.5")

find out more

Remover Pinion Oilseal

Remover Pinion Oilseal

140.81

Application: Freelander 2 and Evoque.

Description: Remover for pinion oilseal. Use with slide hammer LRT-99-004.

Approximate dimensions: Overall length 14cm(5.5")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -