Digital Dispensary

Product Sections


Best Sellers

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Axle Set of Brake Shoes - 10"

Axle Set of Brake Shoes - 10

33.94

Axle set of 4 10inch brake shoes by Lucas-TRW plus 4x pull-off springs, 6x imperial brake drum screws, 2x metric brake drum screws, 2 locking plates and 4 screws for anchor plates.

Application: Series1 80", 86" & 88" front and rear axles, Series 2/2A SWB front and rear, Series3 SWB front and rear to June 1980, Series3 SWB rear only from July 1980, Defender 90 rear to 1994.

Previous part numbers for shoes: RTC3411, GBS728, 505675, 505676
find out more

Rebuild kit for Solex 32PBI-2 Carburettor

Rebuild kit for Solex 32PBI-2 Carburettor

66.04

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor. Zenith part number ZRK17.
Description: A fairly comprehensive kit of parts to rebuild this carburettor.


find out more

Felt Seal Stub Shaft to Drive Flange

Felt Seal Stub Shaft to Drive Flange

0.48

Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
find out more

Pack of 10 3/8"BSF Nyloc Nuts

Pack of 10 3/8

1.92

Pack of ten 3/8"BSF nyloc nuts, 19/32"(15mm) across flats, 0.45"(11.5mm) high.
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Screw for retaining Brake Drums

Screw for retaining Brake Drums

0.25

Application: Series 1, 2 & 3.
Description: Countersunk head screw 3/8"BSW by 5/8" long.
find out more

Gasket Set for Series Gearboxes

Gasket Set for Series Gearboxes

4.20

Application: Series 1, Series 2 & 3 with 4 or 6 cylinder engines.
Description: Set of replacement gaskets for main and transfer gearboxes. Does NOT include seals.
find out more

Acorn for HT Leads

Acorn for HT Leads

1.49

Application: Series One and Series Two. 1948 to 1961 approx.
Description: Acorn nut for retaining high tensions leads to distributor caps and plug caps. Use with 217279 brass washers and copper cored high tension cable.
Approximate dimensions: height 24mm(0.95"), overall diameter 15.4mm(0.6"), thread diameter 12.5mm(0.5")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Gearbox Parts
Page:   <<   <  1  2  3  4  5  ...   >   >>
Selector Shaft - Reverse Gear Ref: 502201
Application: Series 1 & 2 with part syncromesh gearbox.
Description: Selerctor shaft for reverse gear. Photo shows with protective coating still in place.

Price: 40.00 (48.00 Including VAT at 20%)



Selector Shaft - Reverse Gear
Selector Fork 1st/2nd Gears Ref: 6421
Application: Series 1 & 2 with part syncromesh gearbox.
Description: Bronze selector fork for engaging 1st and 2nd gears.

Price: 19.24 (23.09 Including VAT at 20%)



Selector Fork 1st/2nd Gears
Selector Shaft for 1st/2nd Gears Ref: 213637
Application: Series 1 & 2 with part syncromesh gearbox.
Description: Selector shaft for 1st and 2nd gears. Photo shows with wax protective coating still partly in place

Price: 8.00 (9.60 Including VAT at 20%)



Selector Shaft for 1st/2nd Gears
Mounting Bracket for Main Gearlever Ref: 594150
Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Mounting bracket for main gear lever. Comes with threaded hole to take reverse light switch.
Original part number 232608.

Price: 8.00 (9.60 Including VAT at 20%)



Mounting Bracket for Main Gearlever
Spring - Selectors Forward Gears Ref: 3649
Application: All Series 1 and Series 2& 3 with 4 or 6 cylinder engines.
Description: Spring for detent on 1/2 and 3/4 selector shafts.
Approximate dimensions: free length 36mm (1.42"), diameter 9.4mm (0.37").

Price: 0.38 (0.46 Including VAT at 20%)




People who bought this item also bought:
1. Spring - Selector Shaft Reverse (Ref: 56102)
2. Oil Seal Set for Gearbox (Ref: 600603KIT)
3. Return Spring Upper 11" Rear (Ref: 548169D)
Spring - Selectors Forward Gears
Spring - Selector Shaft Reverse Ref: 56102
Application: All Series 1 and Series 2& 3 with 4 or 6 cylinder engines.
Description: Spring for detent on reverse selector shaft. Yellow stripe is for identification.
Approximate dimensions: free length 32mm (1.26"), diameter 9.4mm (0.37").

Price: 0.79 (0.95 Including VAT at 20%)




People who bought this item also bought:
1. Spring - Selectors Forward Gears (Ref: 3649)
2. Oil Seal Set for Gearbox (Ref: 600603KIT)
3. Return Spring Lower 11" Rear (Ref: 531893D)
Spring - Selector Shaft Reverse
Clutch Release Bearing Series1 & 2A Ref: STC1130D
Application: Series1, Series2 and 2A part syncromesh gearbox with the unsealed clutch release mechanism. This is the usual setup on the Series 2 and 2A. This bearing is also used in various gearboxes and transfer boxes.

Description: Single row ball bearing by FAG, type 6207.C3.

Approximate dimensions: overall diameter 72mm (2.83"), inside diameter 35mm (1.38"), thickness 17mm (0.67").

Price: 8.50 (10.20 Including VAT at 20%)




People who bought this item also bought:
1. Bearing First Motion Shaft (Ref: 6397)
2. Oil Seal Set for Gearbox (Ref: 600603KIT)
3. Bearing Layshaft Front - Replacement (Ref: 576207D)
Clutch Release Bearing Series1 & 2A
Clutch Withdrawal Sleeve Ref: 231074
Application: Series 1 & 2 with part syncromesh gearbox.
Description: Clutch withdrawal sleeve, mounted in nose of gearbox.

Price: 60.45 (72.54 Including VAT at 20%)



Clutch Withdrawal Sleeve
Bush Cross-Shaft Clutch Release Ref: 214794
Application: Series 1 & 2 with part syncromesh gearbox.
Description: Bronze bush for cross-shaft of clutch release mechanism. Stil in original packing and grease.

Price: 6.03 (7.24 Including VAT at 20%)



Bush Cross-Shaft Clutch Release
Knob for Main Gear Lever Ref: 217735
Application: Series 1 and early Series2/2A.

Description: Reproduction black gear knob for main gear lever.

Approximate dimensions: Overall diameter 47mm(1.85"), height 37.5mm(1.48"), mounting thread 1/2" BSF.

Price: 36.76 (44.11 Including VAT at 20%)



Knob for Main Gear Lever
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Gearbox Parts
Page:   <<   <  1  2  3  4  5  ...   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Piston Assembly 2.4TDCI

Piston Assembly 2.4TDCI

122.63

Application: Defender from 2007 to 2012 with 2.4 litre TDCI engine.

Description: Standard size piston for 89.90mm bore. Supplied with rings, gudgeon pin and circlips. Made by Nural a Federal Mogul company.



find out more

Electric Fuel Pump - Series 1

Electric Fuel Pump - Series 1

100.44

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Repair Kit for Handbrake Adjuster

Repair Kit for Handbrake Adjuster

4.45

Application: Series 2A and Series 3.

Description: Old stock Lucas Girling repair kit for handbrake adjuster. Includes adjusting screw and wedges plus period tube of brake grease.


find out more

Injector for BMW M57 Diesel Engine

Injector for BMW M57 Diesel Engine

183.77

Application: Range Rover L322 with BMW M57 3.0litre diesel engine.

Description: Reconditioned Bosch injector for the M57 engine. Outright purchase, we do not need your old injector in vexchange.

Approximate dimensions: Overall length 22cm(8.7").

find out more

Bearing and Seals kit for Freelander 1 IRD

Bearing and Seals kit for Freelander 1 IRD

72.54

Application: Freelander 1 IRD unit except V6 model.

Description: Set of 7 OE spec bearings and 4 seals to overhaul the intermediate reduction drive unit. This kit does not include the plate for the oil cooler.

find out more

Rear Diff Repair Kit - Freelander2

Rear Diff Repair Kit - Freelander2

103.14

Application: Freelander 2 and Evoque

Description: Repair kit of OE bearings and seals for the rear differential. Kit includes 4x taper roller bearings, 3x oil seals, 2x 'O' rings, collapsible spacer and pinion nut.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -