Dingocroft Land Rover Series One Axles and Transmission Parts

Product Sections

Best Sellers

Spider Bypass Link Cable

£8.99

Application: Discovery 1 1995 to 1998 approx, where fitted with original immobilisation and alarm system.
Description: Small wiring harness to bypass the "spider" .
See http://forums.lr4x4.com/index.php?showtopic=86 for full instructions on how to fit.
find out more

Connector Kit for Defender Switches

£8.99

Application: Defender 2001 to 2006 with the facelift dash.
Description: Connector kit for auxillary switches on centre dash. This is a direct fit to the front fog lamp switch YUG000540LNF, but will fit the other switches if the splines are removed with a small sharp blade such as a modelling scalpel.
find out more

Connector Kit for Bulb Holders

£3.49

Application: Single pole bulb holders on Defender 1995 onwards, Discovery 1, Discovery 2, Range Rover Classic late,and Range Rover 38A 1995 to 2001.
Description: Connection kit for replacing plug that connects to single pole bulb holder XPB100180.
find out more

Nut and Bolt Kit for Propshafts

£1.54

Application: Series 1, Series 2, Series 2A, Series 3 Land Rovers. All Defenders, Classic Range Rover, Range Rover 2 (38A), Discovery 1 and Discovery 2.
Description: Set of four 3/8UNF x 1.125" long bolts plus four short nyloc nuts.
find out more

Replacement Jate Ring and Fixings

£18.60

Replacement Jate Ring with fixing bolt, nut and spacing washer. Standard equipment on military Defenders. Fixes to chassis rail at front or rear of vehicle. Uses existing mounting holes, so no drilling required.
Application: Defender, Classic Range Rover and Discovery 1.

find out more

Socket for hub nuts

£34.20

Application: Series 1 - 3, Range Rover Classic, Discovery 1 and Defender.
Description: 52mm deep socket, 1/2" drive for hub locking nuts.

find out more

Rebuild kit for Solex 32PBI-2 Carburettor

£40.98

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor. Zenith part number ZRK17.
Description: A fairly comprehensive kit of parts to rebuild this carburettor.
find out more

Standard Set Plus for Defender, Classic Range Rover and Discovery

£162.11

Standard Set Plus of Polybush covers both ends of front radius arms, both ends of rear lower link, Panhard rod bushes, plus rear 'A' frame to chassis.
Application: Defender 1994 to 2001, Classic Range Rover 1986 to 1995, Discovery I 1989 to 1999.
Available in Classic and Comfort Formulas.
find out more

Hub Bearing Kit - Defender, Discovery and Classic Range Rover

£23.94

Application: Defender rear from approx 1985 to 1993, Discovery 1 to 'JA' chassis number (1992) front and rear, Range Rover Classic 1985 to 1995 non-ABS front and rear.
Description: Kit of parts to service one wheel hub. Kit comprises a pair of Timken wheel bearings, Gaco inner seal, replacement outer seal, seal spacer, 2x flange gaskets and hub nut locker.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > Land Rover Series One Parts > Land Rover Series One Axles and Transmission Parts

Axle Breather Ref: 515845=
Application: Series 1, 2 & 3 and Range Rover Classic.
Description: Brass bodied axle breather with one way valve to stop ingress of water when wading.
Price: £2.20 (£2.64 Including VAT at 20%)

Seal Axle Tube Ref: 217400
Application: Front axle of Series 1, 2 & 3.
Description: Oil seal in end of front axle tube. Angus/Gaco manufacture.
Approximate dimensions; overall diameter 63.5mm (2.5"), thickness 9mm (0.35")
Price: £2.39 (£2.87 Including VAT at 20%)

Gear Set - Differential Ref: RTC4489
Application: Series 1, 2 & 3 Rover type differentials.
Description: Matched set of gears and shims for differential.
Original part numbers; set includes 2 each of 06735 & 40760.
Price: £45.00 (£54.00 Including VAT at 20%)

Locker Differential Bolts Ref: 272922
Application: Series 1 & 2.
Description: Locker for crown wheel to differential housing bolts.

Price: £0.25 (£0.30 Including VAT at 20%)

Differential Casing Ref: 273441
Application: Series 1 & 2 Rover type differentials.
Description: Casing or housing for differential gears.
Price: £35.00 (£42.00 Including VAT at 20%)

Differential Housing Ref: 528257
Application: Series 1 and Series 2.
Description: Differential housing for both front and rear axles. Comes with caps and bolts for differential casing retention.
Original part number 219635
Price: £45.00 (£54.00 Including VAT at 20%)

Gasket for Differential to Axle Casing Ref: 7316
Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
Price: £0.50 (£0.60 Including VAT at 20%)

Bearing, Differential Support Ref: 41045
Application: Series 1 and Series 2 differentials.
Description: Taper roller bearing used in pairs to support axle differential. Bearing is numbered 2729/2788.
Approximate dimensions: outside diameter 3" (76.4mm), inside diameter 1.5"(38mm).
Price: £15.00 (£18.00 Including VAT at 20%)

Cross-shaft for Differential Ref: 539703
Application: Series 1 differentials and Series2A Rover type differentials.
Description: Cross-shaft for differential gears.
Approximate dimensions: overall length 123mm (4.85"), diameter 15.5mm (0.61").
Original part number 11378.
Price: £6.00 (£7.20 Including VAT at 20%)

Thrust Washer for Diff Wheels 0.040" Ref: 533786
Application: Series 1 differentials and Series2A Rover type differentials.
Description: Fibre thrust washer for differential wheels.
Approximate dimensions: outside diameter 69mm (2.72"), inside diameter 40mm (1.57"), thickness 1mm (0.040")
Original part number 07902.
Price: £1.00 (£1.20 Including VAT at 20%)

Thrust Washer for Diff Wheels 0.045" Ref: 533787
Application: Series 1 differentials and Series2A Rover type differentials.
Description: Fibre thrust washer for differential wheels.
Approximate dimensions: outside diameter 69mm (2.72"), inside diameter 40mm (1.57"), thickness 1.15mm (0.045")
Original part number 07904.
Price: £1.00 (£1.20 Including VAT at 20%)

Thrust Washer for Diff Wheels 0.050" Ref: 533788
Application: Series 1 differentials and Series2A Rover type differentials.
Description: Fibre thrust washer for differential wheels.
Approximate dimensions: outside diameter 69mm (2.72"), inside diameter 40mm (1.57"), thickness 1.3mm (0.050")
Original part number 50139.
Price: £1.00 (£1.20 Including VAT at 20%)

Shim for Inner bearing of Diff Pinion, 0.003" Ref: 230438
Application: Series 1 and Series 2 differentials.
Description: 0.003" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 78.6mm (3.09"), inside diameter 67mm (2.64").
Price: £1.20 (£1.44 Including VAT at 20%)

Shim for Inner Bearing of Diff Pinion, 0.005" Ref: 230439
Application: Series 1 and Series 2 differentials.
Description: 0.005" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 78.6mm (3.09"), inside diameter 67mm (2.64").
Price: £1.20 (£1.44 Including VAT at 20%)

Shim for Inner Bearing of Diff Pinion, 0.010" Ref: 230440
Application: Series 1 and Series 2 differentials.
Description: 0.010" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 78.6mm (3.09"), inside diameter 67mm (2.64").
Price: £1.20 (£1.44 Including VAT at 20%)

Shim for Inner Bearing of Diff Pinion, 0.020" Ref: 233677
Application: Series 1 and Series 2 differentials.
Description: 0.020" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 78.6mm (3.09"), inside diameter 67mm (2.64").
Price: £1.20 (£1.44 Including VAT at 20%)

Oil Seal Differential Pinion Ref: FRC4586
Application: Series 1, 2 & 3 Rover type differentials.
Description: Oil seal to nose of differential. Corteco/Gaco boxed.
Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").
Original part number: 217507.
Price: £2.96 (£3.55 Including VAT at 20%)

Brass Gasket Differential Nose Ref: 553412=
Application: Series 1 and Series 2 differentials.
Description: Brass gasket/shim for nose peice of differentials. 0.2mm (0.008") thick
Original part number 233473.
Price: £1.00 (£1.20 Including VAT at 20%)

Shim for Outer Bearing of Diff Pinion, 0.010" Ref: 219549
Application: Series 1 and Series 2 differentials.
Description: 0.010" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 41mm (1.6"), inside diameter 32.5mm (1.28").
Price: £0.75 (£0.90 Including VAT at 20%)

Nut and Bolt Kit for Propshafts Ref: PROPFIX01
Application: Series 1, Series 2, Series 2A, Series 3 Land Rovers. All Defenders, Classic Range Rover, Range Rover 2 (38A), Discovery 1 and Discovery 2.
Description: Set of four 3/8UNF x 1.125" long bolts plus four short nyloc nuts.
Price: £1.28 (£1.54 Including VAT at 20%)

Replacement Universal Joint Kit Ref: RTC3291=
Application: Series 1 and Series 2/2A to approximately 1964.
Description: Universal joint repair kit including 4 circlips and a grease nipple.
Approximate Dimensions: Distance across faces of joint 75mm (2.95"), cap diameter 27mm (1.06"), cap length including seal 17mm ( 0.67").
Original part number 43023.
Price: £7.00 (£8.40 Including VAT at 20%)

Related products:

1. Nut and Bolt Kit for Propshafts (Ref: PROPFIX01)

2. Spanner for propshaft nuts and bolts (Ref: ZZBRIRJ562A)

Yoke for Propellor Shaft Ref: 262468
Application: Series 1 & 2.
Description: Yoke for propellor shaft. Only suitable for original prop shafts with the smaller universal joints - RTC3291.
Price: £15.00 (£18.00 Including VAT at 20%)

Genuine Propshaft Gaiter Ref: 276484
Application: Series 1, Series 2/2A, Series 3, early 90/110, Classic Range Rover.
Description: Genuine gaiter and 2 clips for sliding joint on front and rear propellor shafts.
Price: £15.36 (£18.43 Including VAT at 20%)

Replacement Propshaft Gaiter Kit Ref: 276484D
Application: Series 1, Series 2/2A, Series 3, early 90/110, Classic Range Rover.
Description: Replacement gaiter and 2 clips for sliding joint on front and rear propellor shafts.
Price: £3.00 (£3.60 Including VAT at 20%)

Drain Plug - Axle Casing Ref: 235592
Application: Series 1 & 2.
Description: Solid brass drain plug.
Approximate dimensions: outside diameter 34.8mm (1.37"), hight 17.7mm (0.7").
Price: £6.95 (£8.34 Including VAT at 20%)

Related products:

1. Washer for Drain Plug (Ref: 515599)

Washer for Drain Plug Ref: 515599
Application: Series 1 & 2.
Description: Copper crush washer for axle drain plug.
Approximate dimensions: outside diameter 35mm (1.4").
Origilal part number 230509.

Price: £0.36 (£0.43 Including VAT at 20%)

Hub Bearing Rear Ref: 270604
Application: Series 1 with the semi-floating rear axle , that is most of them.
Description: Replacement rear hub bearing. This is the one that is a swine to change. Bearing number 88128R, with shields on both sides.
Approximate dimensions: outside diameter 80mm (3.15"), inside diameter 39mm (1.54"), thickness of outer race 21mm (0.83"), thickness of inner race 27.4mm (1.08").

Price: £67.55 (£81.06 Including VAT at 20%)

Rear Hub Oil Seal Ref: 236923
Application: Series 1 with semi-floating rear axle.
Description: Replacement rear hub oil seal.
Approximate dimensions: outside diameter 70mm (2.76"), thickness 12mm (0.47").
Price: £3.25 (£3.90 Including VAT at 20%)

Series 2 and Series 3 Hub Bearing Kit Ref: WHEELBRGKIT01
Application: Series 1 front axle only, Series 2, Series 2A and Series 3 to 1980. Where inner bearing is larger than outer bearing. Covers both long and short wheel base vehicles, suitable for either front or rear wheel.
Description: Kit of parts to service one wheel hub. Kit comprises inner and outer Timken wheel bearings, Gaco inner seal, flange gasket, hub nut locker, felt outer seal, 'o' ring outer seal and split pin.
Price: £45.00 (£54.00 Including VAT at 20%)

Land on Stub Axle for Hub Seal Ref: 599698
Application: Series 1 front axle, Series 2 and Series 3 upto 1980.
Description: Replaceable land or spacer on stub axle that the wheel hub seal runs on.
Approximate dimensions: outside diameter 2 5/8"(55.8mm), inside diameter 1 13/16" (46mm), depth 7/16"(11mm).
Original part number: 217351
Price: £4.94 (£5.93 Including VAT at 20%)

Stud for wheel Nut Ref: 561590D
Application: Series 1 and Series 2 wheel hubs.
Description: Threaded stud 9/16" BSF x overall length of 43mm (1.6").
Original part number 217360.
Price: £0.76 (£0.91 Including VAT at 20%)

Wheel Nut Ref: 217361
Application: Series 1 and Series 2.
Description: Wheel retaining nut with double chamfer. Thread is 9/16" BSF. Nut is 1" (25.4mm) long by 59/64" (23.4mm) across flats.
Price: £0.65 (£0.78 Including VAT at 20%)

Retaining Collar Half-Shaft Bearing Ref: 90217398D
Application: Series 1, 2 & 3 front axle.
Description: Replacement retaining collar for inner race of bearing for front half shafts'
Approximate dimensions: outside diameter 44.4mm(1.75"), inside diameter 34.8mm (1.25"), length 25mm (1.0")
Original part number: 217398
Price: £7.20 (£8.64 Including VAT at 20%)

Bearing for Front Half-Shaft Ref: 244150=
Application: Series 1, 2 & 3 front axles.
Description: Branded single row roller bearing for supporting front half shaft in end of axle tube.
Approximate dimensions: outside diameter 76.4mm (3"), inside diameter 35mm (1.375"), length 18.5mm (0.73").
Price: £13.10 (£15.72 Including VAT at 20%)

Universal Joint for Front Half-Shafts Ref: RTC3690
Application: Series 1 1952 onwards, Series 2 & 3 front axles.
Description: GKN boxed universal joint for front half-shafts.
Approximate dimensions: 75.5mm (3") across caps, 27mm (1.06") diameter caps.
Original part number: 242521
Price: £12.00 (£14.40 Including VAT at 20%)

Locker Swivel Pin Bolts 3/8" diameter Ref: 270287
Application: Series 1 swivel pin housings and early Series 2 ones.
Description: Locker for 3/8" diameter swivel pin bolts.
Price: £0.40 (£0.48 Including VAT at 20%)

Replacement Swivel Housing S1, S2a & S3 Ref: 539741D
Application: Series 1, Series 2 & 2A, Series 3 (except 109 V8).
Description: Replacement swivel housing for front axle.
Original part number: 234789.
Price: £83.13 (£99.76 Including VAT at 20%)

Swivel Pin Bearing Ref: 217268+
Application: Series 1, 2 & 3.
Description: Timken 21075 taper roller bearing. Fitted to lower swivel pin on front axle.
Approximate dimensions: outside diameter 54mm (2.13"), inside diameter 19mm (0.75")
Price: £9.99 (£11.99 Including VAT at 20%)

Gasket Swivel Housing to Axle Tube Ref: 232413
Application: Series 1, 2 & 3 front axles.
Description: Replacement paper gasket for swivel housing to front axle tube.
Approximate dimensions: overall diameter 12.8cm (5")
Price: £0.15 (£0.18 Including VAT at 20%)

Swivel Housing Outer Seal Ref: RTC3528
Application: Series 1, 2 & 3 front axles.
Description: Genuine oil seal for swivel housings.
Approximate dimensions: Outside diameter 16.8cm (6.6"), thickness 14.7mm (0.58")
Original part number: 502406.
Price: £4.91 (£5.89 Including VAT at 20%)

Retainer Swivel Housing Oil Seal Ref: 235968D
Application: Series 1, 2 & 3.
Description: Reproduction pressed steel retainer for oil seal to swivel housing.
Approximate dimensions: outside diameter 203mm (8"), inside diameter 157mm (6.18").
Price: £1.10 (£1.32 Including VAT at 20%)

Locker for Stub Axle Ref: 277311D
Application: Series 1, 2 & 3.
Description: Replacement locker for stub axle and brake back plate to swivel housing and/or to rear axle tube.
Approximate dimensions: Hole centres 58mm (2.3"), hole diameter 10mm (3/8")
Price: £0.25 (£0.30 Including VAT at 20%)

Gasket, front Stub Axle to Swivel Housing Ref: 277289
Application: Series 1, Series 2 and Series 3.
Description: Gasket between front stub axle and swivel housing.
Approximate dimensions: outside diameter 140mm (5.5"), inside diameter 93mm (3.66").
Price: £0.25 (£0.30 Including VAT at 20%)

Felt Seal Stub Shaft to Drive Flange Ref: RTC3515
Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
Price: £0.40 (£0.48 Including VAT at 20%)

Inner Wheel Hub Seal Ref: RTC3510
Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

Price: £3.50 (£4.20 Including VAT at 20%)

Inner Hub Bearing Ref: RTC3416
Application: Series 1 front hubs, Series 2 & 2A front and rear hubs, Series 3 front and rear hubs to 1980.
Description: Inner wheel hub bearing. Timken taper roller bearing 359S/354X.
Approximate dimensions: outside diameter 85mm (3.35"), inside diameter 46mm (1.8").
Original part number 217269
Price: £19.10 (£22.92 Including VAT at 20%)

Inner Hub Bearing NTN Ref: RTC3416N
Application: Series 1 front hubs, Series 2 & 2A front and rear hubs, Series 3 front and rear hubs to 1980.
Description: Inner wheel hub bearing. NTN (Japanese) taper roller bearing 359S/354X.
Approximate dimensions: outside diameter 85mm (3.35"), inside diameter 46mm (1.8").
Original part number 217269
Price: £18.59 (£22.31 Including VAT at 20%)

Outer Hub Bearing Ref: RTC3426
Application: Series 1 front hubs, Series 2 & 2A front and rear hubs, Series 3 front and rear hubs to 1980.
Description: Outer wheel hub bearing. Timken taper roller bearing 11162/11300.
Approximate dimensions: outside diameter 76.5mm (3.0"), inside diameter 41.2mm (1.62").
Original part number 217270
Price: £24.51 (£29.41 Including VAT at 20%)

Outer Hub Bearing NTN Ref: RTC3426N
Application: Series 1 front hubs, Series 2 & 2A front and rear hubs, Series 3 front and rear hubs to 1980.
Description: Outer wheel hub bearing. NTN (Japanese) taper roller bearing 11162/11300.
Approximate dimensions: outside diameter 76.5mm (3.0"), inside diameter 41.2mm (1.62").
Original part number 217270
Price: £10.80 (£12.96 Including VAT at 20%)

Locker for Hub Nuts Ref: 217353=
Application: Series 1, 2 & 3. Range Rover Classic and early Defender.
Description: Locker for wheel hub nuts.
Approximate dimensions: outside diameter 64.5mm (2.54"), inside diameter 41.6mm (1.64"), thickness 1.0mm *(0.040")
Price: £0.45 (£0.54 Including VAT at 20%)

Key Washer for Hub Bearing Ref: 217352D
Application: Series 1, Series 2 & Series 3.
Description: Thick keyed washer between outer hub bearing and lock nut.
Approximate dimensions: outside diameter 56mm (2.2"), inside diameter 41.5mm (1.63"), thickness 2.8mm (0.11")
Price: £0.60 (£0.72 Including VAT at 20%)

Lock Nut for Hub Bearing Ref: FRC8700D
Application: Series 1, Series 2, Series 3, Range Rover Classic, Discovery 1 and Defender.
Description: Lock nut for hub bearings. Used with second lock nut and locking washer.
Approximate dimensions: 52mm (2 1/16") across flats, thickness 8.5mm (0.33").
Original part number: 217355
Price: £0.85 (£1.02 Including VAT at 20%)

Flange Gasket Ref: 231505=
Application: Series 1, 2 & £.
Description: Paper gasket for drive flange to wheel hub.
Approximate dimensions: outside diameter 112mm (4.4"), inside diameter 77mm (3")
Price: £0.20 (£0.24 Including VAT at 20%)

Cap for Hub Flange Ref: 219098
Application: Series 1, Series 2 and Series 3.
Description: Replacement protection cap for half shaft nut. Finish may be either shiney or dull plating as stock varies.
Price: £0.95 (£1.14 Including VAT at 20%)

Bolt for Hub Flange Ref: 215331
Application: Series 1, Series 2 and Series 3.
Description: Bolt for fixing half shaft drive flange to wheel hub. Six used per hub. Bolt is 3/8" BSF by 1 5/8" long

Price: £0.55 (£0.66 Including VAT at 20%)

Digital Dispensary > Land Rover Series One Parts > Land Rover Series One Axles and Transmission Parts

Haven't found what you want? Then try our quotation service.

Main Pages

New Products

Rear Brake Cylinder

£7.98

Application: Freelander One to 'YA'.
Description: Original equipment rear brake cylinder for vehicles to approx 2000. These cylinders are not handed.
Approximate dimensions: Casting 4.7cm(1.85") long
find out more

Caliper Seal Kit

£6.29

Application: Freelander One from '1A'.
Description: Replacement seals to service both front calipers on later vehicles with vented discs.
Approximate dimensions: 2 seals with outside diameter of 7cm(2.8"), 2 'O' rings with outside diameter of 6cm(2.4")
find out more

Kit of Brake Caliper Guide Pins

£17.58

Application: Freelander One from '1A'.
Description: Genuine kit of guide pins to service pair of front brake calipers.
Approximate dimensions: 2 pins 5.9cm(2.3") long, 2 pins 7.0cm(2.8") long.
find out more

Front Brake Disc - Vented

£14.03

Application: Freelander One from '1A'.
Description: Replacement vented brake disc for front wheels. Priced as single disc, but strongly recommended to be fitted in pairs.
Approximate dimensions: Overall diameter 27.6cm(10.9"), 2.0cm(0.8") thick, offset 3.2cm(1.3")
find out more

Fixing Clip kit for Front Pads

£2.96

Application: Freelander One from '1A'.
Description: Genuine set of 4 fixing clips for front brake pads on vehicles with vented front discs.
Approximate dimensions: Each clip is 7.5cm(3") long.
find out more

Front Brake Pad Set - Genuine

£42.74

Application: Freelander One from '1A'.
Description: Genuine boxed front brake pad set for later models with vented discs. Supplied with 4 new fixing bolts.
Approximate dimensions: Each pad is 13cm(5.1") long by 5.5cm(2.1") wide.
Original part number: SFP500100.
find out more

Front Brake Pad Set

£20.69

Application: Freelander One from '1A'.
Description: Mintex boxed front brake pad set for later models with vented discs.
Approximate dimensions: Each pad is 13cm(5.1") long by 5.5cm(2.1") wide.
find out more

Brake Disc - non vented

£11.40

Application: Freelander One to 'YA'.
Description: Replacement solid brake disc for front wheels. Priced as single disc, but stronglt recommended to be fitted in pairs.
Approximate dimensions: Overall diameter 26.2cm(10.3"), 1.4cm(0.55") thick, offset 4cm(1.6")
find out more

Front Brake Pad Set

£25.16

Application: Freelander One to YA.
Description: Delphi boxed set of front brake pads for early models with solid discs.
Approximate dimensions: Each pad is 13cm(5.1") long by 6.7cm(2.6") wide.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England) email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -

SearchQuest: Internet Marketing, SEO