Digital Dispensary

Product Sections


Best Sellers

Gasket Set for Solex 32PBI-2 Carburettor

Gasket Set for Solex 32PBI-2 Carburettor

7.66

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.
Description: Set of 6 gaskets and 8 fibre washers for this carburettor
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Differential Pinion

Oil Seal Differential Pinion

5.21

Application: Series 1, 2 & 3 Rover type differentials.

Description: Oil seal to nose of differential. Corteco/Gaco boxed.

Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").

Original part number: 217507.
find out more

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Gasket for Differential to Axle Casing

Gasket for Differential to Axle Casing

0.60

Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > RANGE ROVER Classic Parts > Range Rover Classic Electrical Parts
Page:  1  2  3   >   >>
Push/Pull Switch with Illuminated Knob Ref: PRC3289
Application: Range Rover Classic, universal.
Description: High quality push/pull switch by Durite with illuminate knob when on. Original fitment as heated rear window switch on Classic Range Rover 1972 to 1980 approx. However also applicable as auxilliary equipment control switch. Centre of knob glows red when switched on.

Price: 12.50 (15.00 Including VAT at 20%)



Push/Pull Switch with Illuminated Knob
Connector Kit for Bulb Holders Ref: ZZLRA102
Application: Single pole bulb holders on Defender 1995 onwards, Discovery 1, Discovery 2, Range Rover Classic late,and Range Rover 38A 1995 to 2001.
Description: Connection kit for replacing plug that connects to single pole bulb holder XPB100180.

Price: 3.67 (4.40 Including VAT at 20%)



Connector Kit for Bulb Holders
Connector Kit for Bulb Holder - 2 pole Ref: ZZLRA103
Application: Double pole bulb holders on Defender 1995 onwards, Discovery 1, Discovery 2, Range Rover Classic late,and Range Rover 38A 1995 to 2001.
Description: Connection kit for replacing plug that connects to double pole (stop/tail) bulb holder BAU5028L.

Price: 4.10 (4.92 Including VAT at 20%)



Connector Kit for Bulb Holder - 2 pole
Lens LH for Front Lamp Ref: AEU1609
Application: Range Rover Classic up to chassis suffix CA (approx 1986).

Description: Original Lucas L854 lens for right hand side cum indicator lamp.


Price: 65.00 (78.00 Including VAT at 20%)



Lens LH for Front Lamp
Lens RH for Front Lamp Ref: AEU1610
Application: Range Rover Classic up to chassis suffix CA (approx 1986).

Description: Original Lucas L854 lens for right hand side cum indicator lamp.


Price: 65.00 (78.00 Including VAT at 20%)



Lens RH for Front Lamp
Bulb Holder & Lead - Side Repeat Lamp Ref: ZZLRA608
Application: Defender 1995 onwards, Discovery 1 1995 onwards and Range Rover Classic 1993 onwards.
Description: Bulb holder and lead for side repeater indicator lamp. Equivalent to Land Rover part number STC966. Cable length 42cm (16.5").

Price: 27.88 (33.46 Including VAT at 20%)



Bulb Holder & Lead - Side Repeat Lamp
Headlamp Connector Ref: ZZDURITE53951
Application: Sealed beam and H4 bulbs.
Description: Connector kit for sealed beam and H4 headlamps.

Price: 3.01 (3.61 Including VAT at 20%)



Headlamp Connector
Alternator Connector Kit Ref: ZZDURITE0-845-03
Application: Series3, Early Defenders and Early Classic Range Rover. Where ACR type alternators are used.
Description: Connector kit for plug-in type alternators.
Lucas part number 54960402.

Price: 9.65 (11.58 Including VAT at 20%)



Alternator Connector Kit
Regulator for 17ACR Alternator Ref: RTC5932
Application: Range Rover Classic when fitted with 17ACR alternator.

Description: Lucas voltage regulator for alternator.

Alternative part numbers: UCB100, 14TR, 37581D, 607887

Price: 7.00 (8.40 Including VAT at 20%)



Regulator for 17ACR Alternator
Wire Terminal Ref: ZZTERMINAL01
Application: Range Rover Classic.
Description: Wire terminal used in 'E' series connectors. Overall length 22mm(0.9")
Lucas Rists part number 51102699

Price: 0.08 (0.10 Including VAT at 20%)



Wire Terminal
Digital Dispensary > RANGE ROVER Classic Parts > Range Rover Classic Electrical Parts
Page:  1  2  3   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Outer Pinion Bearing

Outer Pinion Bearing

10.72

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for outer end of differential pinion gear. Timken bearing numbers HM88046/HM88010

Approximate dimensions: Outside diameter 2.7"(68.5mm), inside diameter 1.25"(31.8mm)., height 0.93"(23.5mm).


find out more

Inner Pinion Bearing - Differential

Inner Pinion Bearing - Differential

21.70

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for inner end of differential pinion gear. Timken bearing numbers HM801346X/HM801310

Approximate dimensions: Outside diameter 3.25"(82.5mm), inside diameter 1.5"(38mm)., height 1.22"(31mm).

find out more

Seal Kir for 1 1/8" Wheel Cylinders

Seal Kir for 1 1/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for rear wheel cylinders with bore of 1 1/8"(28.5mm). Kit has sufficient seals for both front wheel cylinders.

find out more

Seal Kit for 1 3/8" Wheel Cylinders

Seal Kit for 1 3/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for front wheel cyliders with bore of 1 3/8"(35mm). Kit has sufficient seals for both front wheel cylinders.


find out more

Outlet Nozzle - SU Fuel Pump

Outlet Nozzle - SU Fuel Pump

4.44

Application: Series 1 and early Series 2 models.

Description: Nozzle for outlet of SU fuel pumps. Allows push-on fuel hose connection to pump.

Approximate dimensions: Thread diameter 22mm(0.87"), nozzle diameter 7mm(0.28").

find out more

Wiper Arm Series 3 RH

Wiper Arm Series 3 RH

24.25

Application: Series3 models.

Description: Right hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -