Digital Dispensary

Product Sections


Best Sellers

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Seal Kit for Brake Master Cylinder

Seal Kit for Brake Master Cylinder

19.80

Application: Series One from 1948 to 1958.
Description: Reproduction seal kit for brake master cylinder. Suits all short wheel base models. Not suitable for long wheel base models.
Original part number 278524
find out more

Anchor Plate for 10inch brake shoes

Anchor Plate for 10inch brake shoes

8.44

Anchor plate for use with 10inch brakes - see kit above. One anchor plate is used with each pair of shoes. These do not need replacing with every change of brake shoes, but they do become worn over several years use. Sold singly.
Approximate dimensions: 78mm x 45mm x 5mm.

Application: see STC2796DKIT above.
find out more

Felt Seal Stub Shaft to Drive Flange

Felt Seal Stub Shaft to Drive Flange

0.48

Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Split Pin - Shocker Retention

Split Pin - Shocker Retention

0.25

Application: Series 1, Series 2 and Series 3.

Description: Replacement split pin for retaining shock absorber to bottom plate of spring.

Approximate dimensions: Overall length 55.5mm(2.2"), diameter 6mm(0.24")

find out more

Dust Cap for Bleed Screw

Dust Cap for Bleed Screw

0.30

Application: Suitable for all bleed screws.
Description: Soft plastic dust cap for bleed screws.
Approximate dimensions: length 15mm(0.6"), diameter 8mm (0.3")
Original part number 234957
find out more

Screw for retaining Brake Drums

Screw for retaining Brake Drums

0.25

Application: Series 1, 2 & 3.
Description: Countersunk head screw 3/8"BSW by 5/8" long.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Exhaust Parts
Gasket Exhaust Manifold to Down Pipe Ref: 213358
Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.

Price: 0.80 (0.96 Including VAT at 20%)




People who bought this item also bought:
1. Brake Pipe Set 2A SWB (Ref: ZZGB5601)
2. Pair of Hand Brake Shoes (Ref: STC3821)
3. Grommet - Brake Pipe Support (Ref: 6860L)
Gasket Exhaust Manifold to Down Pipe
Downpipe Ref: 234688
Application: Series One 80" 1948 to 1953.
Description: Replacement exhaust downpipe, shown in some catalogues as 234668.

Due to it's size, this pipe has a supplementary delivery charge. Also for non UK deliveries we have to cut the pipe into 3 sections to keep carriage costs reasonable.


Price: 30.50 (36.60 Including VAT at 20%)



Downpipe
Tailpipe Ref: 233931
Application: Series One 80" 1948 to 1953.

Description: Replacement exhaust tailpipe and silencer.

Due to it's size, this pipe has a supplementary delivery charge. Also for non UK deliveries we have to cut the pipe into 2 sections to keep carriage costs reasonable.

Price: 37.00 (44.40 Including VAT at 20%)



Tailpipe
Exhaust Mounting Rubber Ref: 217608
Application: Series One 80" 1948 to 1953.

Description: Cylindrical exhaust mounting rubber.

Approximate dimensions: Overall length 29mm(1.1"), outside diameter 23.5mm(0.93"), internal diameter 12.4mm(0.5")

Price: 5.80 (6.96 Including VAT at 20%)




People who bought this item also bought:
1. Saddle for Exhaust Bracket (Ref: 233619)
2. Bracket for Tailpipe (Ref: 233618)
3. Gasket Swivel Housing to Axle Tube (Ref: 232413)
Exhaust Mounting Rubber
Bracket for Tailpipe Ref: 233618
Application: Series One 80" 1948 to 1953.

Description: Reproduction galvanised steel tailpipe bracket.

Approximate dimensions: Overall length 155mm(6.1").

Price: 29.55 (35.46 Including VAT at 20%)




People who bought this item also bought:
1. Saddle for Exhaust Bracket (Ref: 233619)
2. Exhaust Mounting Rubber (Ref: 217608)
3. Gasket Swivel Housing to Axle Tube (Ref: 232413)
Bracket for Tailpipe
Saddle for Exhaust Bracket Ref: 233619
Application: Series One 80" 1948 to 1953.

Description: Reproduction galvanised steel saddle clamp for use with bracket 233618.

Approximate dimensions: Overall length 83mm(3.3"), width 32mm(1.3"), height 23mm(0.9"). Hole centres 66.7mm(2 5/8").

Price: 5.95 (7.14 Including VAT at 20%)




People who bought this item also bought:
1. Bracket for Tailpipe (Ref: 233618)
2. Exhaust Mounting Rubber (Ref: 217608)
3. Gasket Swivel Housing to Axle Tube (Ref: 232413)
Saddle for Exhaust Bracket
Exhaust Mounting Bracket Assembly Ref: BRKT1
Application: Series 1 from 1954, Series 2, Series 2A and Series 3 when fitted with 4 cylinder engine.

Description: Complete kit of components to make up first exhaust mount ( from engine end). Suitable for both petrol and diesel engines. On long wheel base 2a models and Series 3 models to suffix B(except Station Wagons) this is the 2nd exhaust mount.

Price: 8.25 (9.90 Including VAT at 20%)




People who bought this item also bought:
1. Speedo Drive Cable (Ref: RTC3484D)
2. Cap for Hub Flange (Ref: 219098)
3. Gaiter for Main Gear Lever (Ref: 301437A)
Exhaust Mounting Bracket Assembly
Exhaust Mounting Bracket Assembly Ref: BRKT3
Application: Series 1 from 1954, Series 2, Series 2A and Series 3 short wheelbase RHD models.

Description: Mounting bracket assembly for tailpipe.

Price: 8.25 (9.90 Including VAT at 20%)




People who bought this item also bought:
1. Throttle Linkage (Ref: 531440)
2. Split Brass Washer (Ref: 214279)
3. Cap for Hub Flange (Ref: 219098)
Exhaust Mounting Bracket Assembly
Digital Dispensary > LAND Rover Series One Parts > Land Rover Series One Exhaust Parts

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Piston Assembly 2.4TDCI

Piston Assembly 2.4TDCI

122.63

Application: Defender from 2007 to 2012 with 2.4 litre TDCI engine.

Description: Standard size piston for 89.90mm bore. Supplied with rings, gudgeon pin and circlips. Made by Nural a Federal Mogul company.



find out more

Electric Fuel Pump - Series 1

Electric Fuel Pump - Series 1

100.44

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Repair Kit for Handbrake Adjuster

Repair Kit for Handbrake Adjuster

4.45

Application: Series 2A and Series 3.

Description: Old stock Lucas Girling repair kit for handbrake adjuster. Includes adjusting screw and wedges plus period tube of brake grease.


find out more

Injector for BMW M57 Diesel Engine

Injector for BMW M57 Diesel Engine

183.77

Application: Range Rover L322 with BMW M57 3.0litre diesel engine.

Description: Reconditioned Bosch injector for the M57 engine. Outright purchase, we do not need your old injector in vexchange.

Approximate dimensions: Overall length 22cm(8.7").

find out more

Bearing and Seals kit for Freelander 1 IRD

Bearing and Seals kit for Freelander 1 IRD

72.54

Application: Freelander 1 IRD unit except V6 model.

Description: Set of 7 OE spec bearings and 4 seals to overhaul the intermediate reduction drive unit. This kit does not include the plate for the oil cooler.

find out more

Rear Diff Repair Kit - Freelander2

Rear Diff Repair Kit - Freelander2

103.14

Application: Freelander 2 and Evoque

Description: Repair kit of OE bearings and seals for the rear differential. Kit includes 4x taper roller bearings, 3x oil seals, 2x 'O' rings, collapsible spacer and pinion nut.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -