Digital Dispensary

Product Sections


Best Sellers

'O' Ring for Thermostat

'O' Ring for Thermostat

0.55

Application: Series 1, 2 & 3 4cylinder engines.
Description: 'O' ring for sealing thermostat to cylinder head.
Approximate dimensions: outside diameter 55mm (2.2").
Original part number 01645
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Thermostat 82 degrees

Thermostat 82 degrees

10.61

Application: Series 1 1.6ltr & 2.0ltr petrol engines, Defender 2.5 & 2.5TD diesel engines.

Description: Waxstat 82degree thermostat.

Original part number: 504560.

find out more

Gasket Exhaust Manifold to Down Pipe

Gasket Exhaust Manifold to Down Pipe

0.96

Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Brass Nut 5/16"BSF

Brass Nut 5/16

1.66

Application: Series1 exhaust manifold.

Description: Brass nut 5/16"BSF for holding downpipe to exhaust manifold.

Approximate dimensions: 3/8"(9.5mm) high, 17/32"(13.5mm) across flats.

find out more

Fixings Kit for Water Pump

Fixings Kit for Water Pump

19.87

Application: Series One, 1948 to 1958.

Description: Set of fixings for water pump comprising the following parts;
6x 250517 bolt 1/4"BSF x 1.5", 1x 250518 bolt 1/4"BSF x 1.75", 1x 237150 bolt 1/4"BSF x 2.25", 2x set screw 5/16"BSW x 11/16" plus 8x 1/4" lock washers and 2x 5/16" lock washers.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > REGULAR Service and Repair Parts > Braking Systems > Hydraulics and application systems
Page:  1  2  3  4  5  ...   >   >>
Pair of Front Wheel Cylinders Ref: 212912/3
Application: Series 1 80" 1948 to 1953.

Description: Pair of replacement wheel cylinders with banjo connectors to take brake hoses with 7/16" UNF threaded ends. Supplied with bleed nipples. These cylinders have a bore of 1.25"(31.8MM).
NB we can no longer source the brass banjos, just the banjo bolt. So your old brass banjos will have to be re-used.

Price: 115.00 (138.00 Including VAT at 20%)




People who bought this item also bought:
1. Steering Box Repair Kit (Ref: STRGBOXKIT01)
2. Grommet Series 1 Pedals (Ref: 70620)
3. Bleed Screw for Wheel Cylinders (Ref: 556508)


Related products:
1. 1litre Bottle of Silicon Brake Fluid (Ref: ZZDYNSILIDOT5)
Pair of Front Wheel Cylinders
Lucas Wheel Cylinder S1, S2A & S3 Ref: 243296=
Application: Front right hand cylinder on SWB models to 1980, rear RH wheel cylinder on SWB models fron 1980 onwards. Rear RH wheel cylinder on all 109 models.
Description: Brake wheel cylinder for use with 10 inch brake drums, has 1.25" diameter bore.
Approximate dimensions: Length 83mm (3.3"), bore diameter 31.8mm (1.25"), mounting stud centres 42mm (1.65").

Price: 26.89 (32.27 Including VAT at 20%)




People who bought this item also bought:
1. Lucas Wheel Cylinder S1, S2A & S3 (Ref: 243297=)
Lucas Wheel Cylinder S1, S2A & S3
Lockheed Delphi Wheel Cylinder S1, S2a & S3 Ref: 243296D
Application: Front right hand cylinder on SWB models to 1980, rear RH wheel cylinder on SWB models fron 1980 onwards. Rear RH wheel cylinder on all 109 models.
Description: Brake wheel cylinder for use with 10 inch brake drums. Bore diameter 1.25".
Approximate dimensions: Length 83mm (3.3"), bore diameter 31.8mm (1.25"), mounting stud centres 42mm (1.65").

Price: 15.00 (18.00 Including VAT at 20%)




People who bought this item also bought:
1. Axle Set of Brake Shoes - 10" (Ref: STC2796DKIT)
2. Lockheed Delphi Wheel Cylinder S1, S2A & S3 (Ref: 243303D)
3. Lockheed Delphi Wheel Cylinder S1, S2A & S3 (Ref: 243302D)
Lockheed Delphi Wheel Cylinder S1, S2a & S3
Lucas Wheel Cylinder S1, S2A & S3 Ref: 243297=
Application: Front left hand cylinder on SWB models to 1980, rear LH wheel cylinder on SWB models fron 1980 onwards. Rear LH wheel cylinder on all 109 models.
Description: Brake wheel cylinder for use with 10 inch brake drums. Main castings is of Aluminium.
Approximate dimensions: Length 83mm (3.3"), bore diameter 31.8mm (1.25"), mounting stud centres 42mm (1.65").

Price: 26.89 (32.27 Including VAT at 20%)




People who bought this item also bought:
1. Lucas Wheel Cylinder S1, S2A & S3 (Ref: 243296=)
Lucas Wheel Cylinder S1, S2A & S3
Lockheed Delphi Wheel Cylinder S1, S2A & S3 Ref: 243297D
Application: Front left hand cylinder on SWB models to 1980, rear LH wheel cylinder on SWB models fron 1980 onwards. Rear LH wheel cylinder on all 109 models.
Description: Brake wheel cylinder for use with 10 inch brake drums. Main castings is of cast iron.
Approximate dimensions: Length 83mm (3.3"), bore diameter 31.8mm (1.25"), mounting stud centres 42mm (1.65").

Price: 15.00 (18.00 Including VAT at 20%)




People who bought this item also bought:
1. Axle Set of Brake Shoes - 10" (Ref: STC2796DKIT)
2. Lockheed Delphi Wheel Cylinder S1, S2A & S3 (Ref: 243303D)
3. Lockheed Delphi Wheel Cylinder S1, S2A & S3 (Ref: 243302D)
Lockheed Delphi Wheel Cylinder S1, S2A & S3
Seal Kit - front wheel cylinders Ref: 275744
Application: Series 1, 2 & 3.
Description: Replacement seal kit for pair of 1.25" bore wheel cylinders. Contains 4 cup seals for pistons, 4 dust seals for cylinder ends and 2 dust caps for bleed screws. Suits cylinders 243296 and 243297.

Price: 2.50 (3.00 Including VAT at 20%)




People who bought this item also bought:
1. Replacement Propshaft Gaiter Kit (Ref: 276484D)
2. Pair of Front Wheel Cylinders (Ref: 212912/3)
3. Rubber Boot for Steering Ball Joint (Ref: 214649)


Related products:
1. Cylinder Hones - Brakes (Ref: ZZLAS2243)
2. 1litre Bottle of Silicon Brake Fluid (Ref: ZZDYNSILIDOT5)
Seal Kit - front wheel cylinders
Lockheed Delphi Wheel Cylinder S1, S2A & S3 Ref: 243302D
Application: 88 inch wheel base rear right hand to 1980. Used in 10 inch drums.

Description: Cast iron wheel cylinder by Lockheed Delphi. Internal bore 25mm (1 inch), length 84mm (3.3 ionches). NB on early vehicles this cylinder was used on the left hand rear drum.

Price: 15.00 (18.00 Including VAT at 20%)




People who bought this item also bought:
1. Lockheed Delphi Wheel Cylinder S1, S2A & S3 (Ref: 243303D)
2. Repair Kit for S U Fuel Pump pre 1985 (Ref: ZZEPK700)
3. Axle Set of Brake Shoes - 10" (Ref: STC2796DKIT)
Lockheed Delphi Wheel Cylinder S1, S2A & S3
Lockheed Delphi Wheel Cylinder S1, S2A & S3 Ref: 243303D
Application: 88 inch wheel base rear left hand to 1980. Used in 10 inch drums.

Description: Cast iron wheel cylinder by Lockheed Delphi. Internal bore 25mm (1 inch), length 84mm (3.3 ionches). NB on early vehicles this cylinder was used on the right hand rear drum.

Price: 15.00 (18.00 Including VAT at 20%)




People who bought this item also bought:
1. Lockheed Delphi Wheel Cylinder S1, S2A & S3 (Ref: 243302D)
2. Repair Kit for S U Fuel Pump pre 1985 (Ref: ZZEPK700)
3. Axle Set of Brake Shoes - 10" (Ref: STC2796DKIT)
Lockheed Delphi Wheel Cylinder S1, S2A & S3
Replacement Seal Kit for Wheel Cylinders Ref: 266687
Application: Series 1, 2, & 3 with 1" diameter bore wheel cylinders as fitted to rear of 86" & 88" wheel base Land Rovers.
Description: Seal kit for pair of 1" diameter wheel cylinders. Kit contains 4 cup seals, 4 cylinder dust seals and 2 dust caps for bleed screws. Suits 243302 and 243303 wheel cylinders.

Please note that this is now a replacement kit as the Lockheed kit is no longer available.

Price: 2.50 (3.00 Including VAT at 20%)




People who bought this item also bought:
1. Screw for retaining Brake Drums (Ref: 1510)
2. Replacement Propshaft Gaiter Kit (Ref: 276484D)
3. Rubber Boot for Steering Ball Joint (Ref: 214649)


Related products:
1. Cylinder Hones - Brakes (Ref: ZZLAS2243)
Replacement Seal Kit for Wheel Cylinders
Lucas Wheel Cylinder Series 2A & 3 Ref: 243743
Application: 109 4cylinder front left hand wheel cylinder. 2 per wheel. Also 88" front left hand wheel cylinder from 1980 onwards.
Description: Lucas single piston wheel cylinder with cast iron body.
Approximate dimensions: length 57mm (2.24"), bore 28.5mm (1.125").

Price: 18.00 (21.60 Including VAT at 20%)




People who bought this item also bought:
1. Axle Set of Brake Shoes - 11" Front (Ref: STC3944DKIT)
2. Spring Bush for 2.5" wide Springs (Ref: 548205)
3. Return Spring - Leading Shoe 10" (Ref: 503981)
Lucas Wheel Cylinder Series 2A & 3
Digital Dispensary > REGULAR Service and Repair Parts > Braking Systems > Hydraulics and application systems
Page:  1  2  3  4  5  ...   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Locking Hasp for Fuel Cap

Locking Hasp for Fuel Cap

4.50

Application: Series 2a and Series 3.

Description: Locking hasp for fuel cap with 'ears'. Allows use of padlock to secure fuel cap.

Approximate dimensions: Mounting screw centres 70mm(2.75")

Old part number: GLR361

find out more

Bail Assembly

Bail Assembly

2.70

Application: Series 2A and Series 3.

Description: Retainer for glass bowl on side of lift pump on 4 cylinder models.

Approximate dimensions: Overall length 92mm, width 58mm.

find out more

Fuel Filler Cap

Fuel Filler Cap

26.46

Application: Series 2a and Series 3.

Description: Old stock Unipart 2 lug fuel filler cap. Supplied with seal,

Approximate dimensions: Overa;; diameter 96mm(3.8").

find out more

6 Way Lighting Switch - Military

6 Way Lighting Switch - Military

153.60

Application: Series3, Light Weight, 101 and Defender military models.

Description: Old stock Lucas 34259 six way lighting swith with facility for lock barrel (not supplied).


find out more

Bypass Hose Series 1 1948-1953

Bypass Hose Series 1 1948-1953

8.70

Application: Series 1 1948 to 1953 with 1.6 litre and early 2 litre engines.

Description: Reproduction bypass hose.

Approximate dimensions: Overall length 88mm(3.5"), outside diameter 45mm(1.8"), inside diameter 34mm(1.3")

find out more

Engine Breather-Filter

Engine Breather-Filter

22.69

Application: Defender with 2.5litre naturally aspirated diesel engine.

Description: Breather cap on top of rocker cover with single pipe outlet of 19mm diameter.

find out more

Installer Oil Seal

Installer Oil Seal

131.21

Application: Freelander2 and Evoque.

Description: Installer for oil seal. Beleived to be on front differential.

Approximate dimensions: Overall length 19.4cm(7.6"), overall diameter 90mm(3.5")

find out more

Remover Pinion Oilseal

Remover Pinion Oilseal

140.81

Application: Freelander 2 and Evoque.

Description: Remover for pinion oilseal. Use with slide hammer LRT-99-004.

Approximate dimensions: Overall length 14cm(5.5")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -