Digital Dispensary

Product Sections


Best Sellers

'O' Ring for Thermostat

'O' Ring for Thermostat

0.55

Application: Series 1, 2 & 3 4cylinder engines.
Description: 'O' ring for sealing thermostat to cylinder head.
Approximate dimensions: outside diameter 55mm (2.2").
Original part number 01645
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Thermostat 82 degrees

Thermostat 82 degrees

10.61

Application: Series 1 1.6ltr & 2.0ltr petrol engines, Defender 2.5 & 2.5TD diesel engines.

Description: Waxstat 82degree thermostat.

Original part number: 504560.

find out more

Gasket Exhaust Manifold to Down Pipe

Gasket Exhaust Manifold to Down Pipe

0.96

Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Brass Nut 5/16"BSF

Brass Nut 5/16

1.66

Application: Series1 exhaust manifold.

Description: Brass nut 5/16"BSF for holding downpipe to exhaust manifold.

Approximate dimensions: 3/8"(9.5mm) high, 17/32"(13.5mm) across flats.

find out more

Fixings Kit for Water Pump

Fixings Kit for Water Pump

19.87

Application: Series One, 1948 to 1958.

Description: Set of fixings for water pump comprising the following parts;
6x 250517 bolt 1/4"BSF x 1.5", 1x 250518 bolt 1/4"BSF x 1.75", 1x 237150 bolt 1/4"BSF x 2.25", 2x set screw 5/16"BSW x 11/16" plus 8x 1/4" lock washers and 2x 5/16" lock washers.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > REGULAR Service and Repair Parts > Braking Systems > Hydraulics and application systems
Page:   <<   <  6  7   >   >>
Replacement Brake Hose Series 3 & 90/110 Ref: NRC9456D
Application: Series 3 88" rear from 1980 onwards, (Defender) 90/110 rear to 1994.
Description: Replacement brake hose with protective spiral steel outer. Overall length 42.5cm (16.7"), 10mm metric fine threaded unions.

Price: 6.00 (7.20 Including VAT at 20%)



Replacement Brake Hose Series 3 & 90/110
Replacement Brake Hose Series 3 Ref: NTC3458D
Application: Series 3 109" rear from 1980 onwards.
Description: Replacement brake hose overall length 44cm (17.3") threaded ends are 10mm metric fine.

Price: 6.00 (7.20 Including VAT at 20%)



Replacement Brake Hose Series 3
Tee Piece Ref: BTB657L
Application: Series 1 from 1954, Series 2/2A and Series 3 to 1980.
Description: Reproduction tee piece in brass to take 3x 3/16" brake pipes with 3/8"UNF threaded unions. Also with mounting hole.
Original part number 234928

Price: 9.64 (11.57 Including VAT at 20%)




People who bought this item also bought:
1. Brass 'T' Piece for 1/4" Pipes (Ref: ZZHU34)
2. Felt Seal for Series 1 Pedals (Ref: 70621)
3. 80" Brake Pipe Set RHD (Ref: ZZGB5600)
Tee Piece
Tee Piece - Metric Ref: NRC4251D
Application: Series 3 1980 onwards, Defender, Discovery 1 and Range Rover Classic.

Description: Replacement brass 'T' piece to take 3 3/16" diameter brake pipes with 10mm diameter metric male unions.

Price: 2.55 (3.06 Including VAT at 20%)



Tee Piece - Metric
4-Way Brake Pipe Union Ref: 565719
Application: Series One from 1954 to 1958. Series 2/2A with mechanical brake light switch.
Description: Reproduction 4-way brake union in solid brass. Takes 4 3/16" brake pipes with 3/8"UNF 24TPI threads. Also has fixing hole.
Original part number 241690

Price: 14.80 (17.76 Including VAT at 20%)



4-Way Brake Pipe Union
5 Way Brake Connector Ref: 279412
Application: Series 2 and 2A with hydraulic brake light switch.

Description: Reproduction brass 5 way connector. All five connections are threaded 3/8"unf. This connector will not take the original brake light switch, however ZZ21B291 (below) does fit.

Approximate dimensions: 41.5mm(1.6") across faces, 28mm(1.1") high

Price: 29.61 (35.53 Including VAT at 20%)



5 Way Brake Connector
Hydraulic Brake Light Switch Ref: ZZ21B291
Application: 279412 reproduction 5 way connector.
Description: Hydraulic brake light switch with 3/8"unf 24TPI male thread. This switch does not fit the original 5 way connector. However it will fit the reproduction 5 way connector and also the 4 way connector 241690 and the 'T' piece BTB657, this makes it useful for the 'special' builder. Supplied with copper washer 233220 to seal to union.

Approximate dimensions: overall length 38mm(1.5"), hex 22mm(0.87") across flats.

Price: 10.42 (12.50 Including VAT at 20%)



Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Ref: STC1689
Application: Series 2 and 2A .

Description: Hydraulic brake light switch for use with original 5-way connector. This switch has 1/4"BSP male thread.

Approximate dimensions: 39mm(1.5") overall length, 22mm(0.9") across flats.

Previous part numbers: 560775, Lucas 34545.

Price: 4.50 (5.40 Including VAT at 20%)



Hydraulic Brake Light Switch
Brake Light Switch Ref: 13H3735L
Application: Series 2A post hydraulic switch, Series 3 non servo, Range Rover Classic, Discovery 1.

Description: Lucas boxed plastic bodies brake light switch. Default position of switch is ON, plunger is pushed in to turn OFF.

Approximate dimensions: Overall length 54.5mm(2.1"), fits 1/2" diameter mounting hole.

Price: 2.95 (3.54 Including VAT at 20%)



Brake Light Switch
Brake Light Switch Series 3 Ref: 575166
Application: Series 3 with servo brakes.

Description: Genuine boxed brass brake light switch used on models with servo brakes. Mounted on top of brake pedal box, under the bonnet. Supplied with lock nut.

Approximate dimensions: 3/8"unf mounting thread, overall length 46mm

Price: 35.78 (42.94 Including VAT at 20%)



Brake Light Switch Series 3
Digital Dispensary > REGULAR Service and Repair Parts > Braking Systems > Hydraulics and application systems
Page:   <<   <  6  7   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Locking Hasp for Fuel Cap

Locking Hasp for Fuel Cap

4.50

Application: Series 2a and Series 3.

Description: Locking hasp for fuel cap with 'ears'. Allows use of padlock to secure fuel cap.

Approximate dimensions: Mounting screw centres 70mm(2.75")

Old part number: GLR361

find out more

Bail Assembly

Bail Assembly

2.70

Application: Series 2A and Series 3.

Description: Retainer for glass bowl on side of lift pump on 4 cylinder models.

Approximate dimensions: Overall length 92mm, width 58mm.

find out more

Fuel Filler Cap

Fuel Filler Cap

26.46

Application: Series 2a and Series 3.

Description: Old stock Unipart 2 lug fuel filler cap. Supplied with seal,

Approximate dimensions: Overa;; diameter 96mm(3.8").

find out more

6 Way Lighting Switch - Military

6 Way Lighting Switch - Military

153.60

Application: Series3, Light Weight, 101 and Defender military models.

Description: Old stock Lucas 34259 six way lighting swith with facility for lock barrel (not supplied).


find out more

Bypass Hose Series 1 1948-1953

Bypass Hose Series 1 1948-1953

8.70

Application: Series 1 1948 to 1953 with 1.6 litre and early 2 litre engines.

Description: Reproduction bypass hose.

Approximate dimensions: Overall length 88mm(3.5"), outside diameter 45mm(1.8"), inside diameter 34mm(1.3")

find out more

Engine Breather-Filter

Engine Breather-Filter

22.69

Application: Defender with 2.5litre naturally aspirated diesel engine.

Description: Breather cap on top of rocker cover with single pipe outlet of 19mm diameter.

find out more

Installer Oil Seal

Installer Oil Seal

131.21

Application: Freelander2 and Evoque.

Description: Installer for oil seal. Beleived to be on front differential.

Approximate dimensions: Overall length 19.4cm(7.6"), overall diameter 90mm(3.5")

find out more

Remover Pinion Oilseal

Remover Pinion Oilseal

140.81

Application: Freelander 2 and Evoque.

Description: Remover for pinion oilseal. Use with slide hammer LRT-99-004.

Approximate dimensions: Overall length 14cm(5.5")

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -