Digital Dispensary

Product Sections


Best Sellers

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Seal Kit for Brake Master Cylinder

Seal Kit for Brake Master Cylinder

19.80

Application: Series One from 1948 to 1958.
Description: Reproduction seal kit for brake master cylinder. Suits all short wheel base models. Not suitable for long wheel base models.
Original part number 278524
find out more

Anchor Plate for 10inch brake shoes

Anchor Plate for 10inch brake shoes

8.44

Anchor plate for use with 10inch brakes - see kit above. One anchor plate is used with each pair of shoes. These do not need replacing with every change of brake shoes, but they do become worn over several years use. Sold singly.
Approximate dimensions: 78mm x 45mm x 5mm.

Application: see STC2796DKIT above.
find out more

Felt Seal Stub Shaft to Drive Flange

Felt Seal Stub Shaft to Drive Flange

0.48

Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Split Pin - Shocker Retention

Split Pin - Shocker Retention

0.25

Application: Series 1, Series 2 and Series 3.

Description: Replacement split pin for retaining shock absorber to bottom plate of spring.

Approximate dimensions: Overall length 55.5mm(2.2"), diameter 6mm(0.24")

find out more

Dust Cap for Bleed Screw

Dust Cap for Bleed Screw

0.30

Application: Suitable for all bleed screws.
Description: Soft plastic dust cap for bleed screws.
Approximate dimensions: length 15mm(0.6"), diameter 8mm (0.3")
Original part number 234957
find out more

Screw for retaining Brake Drums

Screw for retaining Brake Drums

0.25

Application: Series 1, 2 & 3.
Description: Countersunk head screw 3/8"BSW by 5/8" long.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Engine Electrics and Ignition Land Rover Ser2,2A and 3.
Page:  1  2  3  4  5   >   >>
High Torque Starter Motor Ref: RTC5225HT
Application: Series 2A and Series 3 4 cylinder petrol engines.

Description: 12volt gear reduction high torque starter motor made in UK by Powerlite. This replaces original inertia type starter motor and is supplied with instructions. Unfortunately it is not suitable for the 6 cylinder engine as the solenoid housing fouls on the bulkhead.

Approximate dimensions: Overall length 19cm, height 15cm.

Price: 169.80 (203.76 Including VAT at 20%)



High Torque Starter Motor
Starter 2.25 Diesel S2 & S3 Ref: RTC5232D
Application: 2.25 diesel engine as fitted to Series2A and Series 3.

Description: Gear reduced equivalent of original starter.

Previous part numbers: RTC3857 GEU4435 and GEU435

Price: 99.45 (119.34 Including VAT at 20%)



Starter 2.25 Diesel S2 & S3
Solenoid for Diesel Starter Ref: STC1518
Application: Series 3 with 2.25 litre diesel engine.

Description: European made 'OE' specification solenoid for use on original Lucas starter motor as fitted to Series 3.


Original part number: AEU1649.

Price: 25.27 (30.32 Including VAT at 20%)



Solenoid for Diesel Starter
Sundry Parts Kit - Diesel Starter Ref: 605622
Application: Lucas diesel starter 26321 & 27425. Used on late Series 2A and Series 3.

Description: Kit of 23 small parts of these Lucas starters

Price: 6.00 (7.20 Including VAT at 20%)



Sundry Parts Kit - Diesel Starter
Resistor - Heater Plugs Ref: PRC1716
Application: Series 2a & Series 3 diesel models.

Description: Replacement in-line resistor for heater plugs. This is for early set-up where plugs are wired in series.

Approximate dimensions: Overall length 13cm(2.1"), width 3.1cm(1.2"), depth 5.5cm(2.2")

Price: 7.80 (9.36 Including VAT at 20%)



Resistor - Heater Plugs
Starter for Rover V8 Ref: RTC6061N
Application: Range Rover Classic. Series 3 109V8, Defender, Discovery1 & 2, Range Rover 38A where fitted with Rover V8 from 3.5litre to 4.6litre.

Description: Denso manufasctured new starter. Replacement for earlier Lucas starters as well as later small bodied starters.

Approximate dimensdions: Overall length 24cm(9.5"), body diameter 7.4cm(2.9"), mounting bolt centres 118mm(4.65")

Price: 114.16 (136.99 Including VAT at 20%)



Starter for Rover V8
Brush Set for Starter Motor Ref: 260055
Application: Series 1 and Series 2 petrol starter motor.

Description: Pair of brushes for starter motor.

Approximate dimensions: Each brush is 19mm(3/4") x 14mm(0.55") x 9mm(0.35") with lead of 95mm(3.75")

Alternative part numbers: LU255659, GSB103.

Price: 4.14 (4.97 Including VAT at 20%)




People who bought this item also bought:
1. Sealing Ring Water Pump to Cylinder Head (Ref: RTC1975)
2. Brush Set for Dynamo (Ref: 261483)
3. Spark Plug Cover (Ref: ZZSB05F)
Brush Set for Starter Motor
Dynamo Series 2 and 2A Ref: RTC3840D
Application: Series 2 and 2A 2.25 litre petrol engines.

Description: Replacement dynamo for both positive and negative earth Series 2 and 2A petrol models.

Price: 58.00 (69.60 Including VAT at 20%)



Dynamo Series 2 and 2A
Brush Set for Dynamo Ref: 261483
Application: Series 1 1948 to 1958, Series 2 1958 to 1960.

Description: Pair of brushes for ucas C39 dynamo.

Approximate dimensions: Each brush is 19mm(3/4") x 16mm(5/8") x 6.5mm1/4"). Lead is 50mm(2") long.

Price: 3.60 (4.32 Including VAT at 20%)




People who bought this item also bought:
1. Ignition Coil (Ref: 263732D)
2. Sealing Ring Water Pump to Cylinder Head (Ref: RTC1975)
3. Brush Set for Starter Motor (Ref: 260055)
Brush Set for Dynamo
Reconditioned Alternator 16ACR Ref: RTC5084D
Application: Series 3 4cylinder and 6 cylinder engines.
Description: Reconditioned alternator 16ACR 34amp 12volt. Supplied without pulley, but does come with nut, washer and key.

Price: 45.00 (54.00 Including VAT at 20%)



Reconditioned Alternator 16ACR
Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Engine Electrics and Ignition Land Rover Ser2,2A and 3.
Page:  1  2  3  4  5   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Piston Assembly 2.4TDCI

Piston Assembly 2.4TDCI

122.63

Application: Defender from 2007 to 2012 with 2.4 litre TDCI engine.

Description: Standard size piston for 89.90mm bore. Supplied with rings, gudgeon pin and circlips. Made by Nural a Federal Mogul company.



find out more

Electric Fuel Pump - Series 1

Electric Fuel Pump - Series 1

100.44

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Repair Kit for Handbrake Adjuster

Repair Kit for Handbrake Adjuster

4.45

Application: Series 2A and Series 3.

Description: Old stock Lucas Girling repair kit for handbrake adjuster. Includes adjusting screw and wedges plus period tube of brake grease.


find out more

Injector for BMW M57 Diesel Engine

Injector for BMW M57 Diesel Engine

183.77

Application: Range Rover L322 with BMW M57 3.0litre diesel engine.

Description: Reconditioned Bosch injector for the M57 engine. Outright purchase, we do not need your old injector in vexchange.

Approximate dimensions: Overall length 22cm(8.7").

find out more

Bearing and Seals kit for Freelander 1 IRD

Bearing and Seals kit for Freelander 1 IRD

72.54

Application: Freelander 1 IRD unit except V6 model.

Description: Set of 7 OE spec bearings and 4 seals to overhaul the intermediate reduction drive unit. This kit does not include the plate for the oil cooler.

find out more

Rear Diff Repair Kit - Freelander2

Rear Diff Repair Kit - Freelander2

103.14

Application: Freelander 2 and Evoque

Description: Repair kit of OE bearings and seals for the rear differential. Kit includes 4x taper roller bearings, 3x oil seals, 2x 'O' rings, collapsible spacer and pinion nut.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -