Digital Dispensary

Product Sections


Best Sellers

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Seal Kit for Brake Master Cylinder

Seal Kit for Brake Master Cylinder

19.80

Application: Series One from 1948 to 1958.
Description: Reproduction seal kit for brake master cylinder. Suits all short wheel base models. Not suitable for long wheel base models.
Original part number 278524
find out more

Anchor Plate for 10inch brake shoes

Anchor Plate for 10inch brake shoes

8.44

Anchor plate for use with 10inch brakes - see kit above. One anchor plate is used with each pair of shoes. These do not need replacing with every change of brake shoes, but they do become worn over several years use. Sold singly.
Approximate dimensions: 78mm x 45mm x 5mm.

Application: see STC2796DKIT above.
find out more

Felt Seal Stub Shaft to Drive Flange

Felt Seal Stub Shaft to Drive Flange

0.48

Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Split Pin - Shocker Retention

Split Pin - Shocker Retention

0.25

Application: Series 1, Series 2 and Series 3.

Description: Replacement split pin for retaining shock absorber to bottom plate of spring.

Approximate dimensions: Overall length 55.5mm(2.2"), diameter 6mm(0.24")

find out more

Dust Cap for Bleed Screw

Dust Cap for Bleed Screw

0.30

Application: Suitable for all bleed screws.
Description: Soft plastic dust cap for bleed screws.
Approximate dimensions: length 15mm(0.6"), diameter 8mm (0.3")
Original part number 234957
find out more

Screw for retaining Brake Drums

Screw for retaining Brake Drums

0.25

Application: Series 1, 2 & 3.
Description: Countersunk head screw 3/8"BSW by 5/8" long.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > REGULAR Service and Repair Parts > Braking Systems > Drums and shoes. Discs and pads.
Page:  1  2  3  4   >   >>
Axle Set of Brake Shoes - 10" Ref: STC2796DKIT
Axle set of 4 10inch brake shoes by Lucas-TRW plus 4x pull-off springs, 6x imperial brake drum screws, 2x metric brake drum screws, 2 locking plates and 4 screws for anchor plates.

Application: Series1 80", 86" & 88" front and rear axles, Series 2/2A SWB front and rear, Series3 SWB front and rear to June 1980, Series3 SWB rear only from July 1980, Defender 90 rear to 1994.

Previous part numbers for shoes: RTC3411, GBS728, 505675, 505676

Price: 28.28 (33.94 Including VAT at 20%)




People who bought this item also bought:
1. Snail Cam Replacement Kit (Ref: RTC3176D)
2. Locker for Hub Nuts (Ref: 217353=)
3. Radiator Cap 7lb (Ref: 217437)
Axle Set of Brake Shoes - 10
Anchor Plate for 10inch brake shoes Ref: 236993
Anchor plate for use with 10inch brakes - see kit above. One anchor plate is used with each pair of shoes. These do not need replacing with every change of brake shoes, but they do become worn over several years use. Sold singly.
Approximate dimensions: 78mm x 45mm x 5mm.

Application: see STC2796DKIT above.

Price: 7.03 (8.44 Including VAT at 20%)




People who bought this item also bought:
1. Axle Set of Brake Shoes - 10" (Ref: STC2796DKIT)
2. Dust Cap for Bleed Screw (Ref: 594091)
3. Seal Kit for Brake Master Cylinder (Ref: ZZSP1975-5)
Anchor Plate for 10inch brake shoes
Locker for Anchor Plate Ref: 236995
Application: Series 1, 2 & 3 with 10" brakes.
Description: Locker for brake shoe anchor plate.
Approximate dimensions: 3.8cm(1.5") long by 1cm(3/8") wide by 1mm(0.040") thick.

Price: 1.02 (1.22 Including VAT at 20%)




People who bought this item also bought:
1. Grommet - Brake Pipe Support (Ref: 6860L)
2. Dust Cap for Bleed Screw (Ref: 594091)
3. Anchor Plate for 10inch brake shoes (Ref: 236993)
Locker for Anchor Plate
Return Spring - Brake Shoes 10" Ref: 218983
Application: Series 1, 2 & 3 with 10" brakes. Also Defender 90 to 1994.

Description: Lower pull-off spring across both shoes.

Approximate dimensions: overall length 87mm(3.4")

Price: 0.50 (0.60 Including VAT at 20%)




People who bought this item also bought:
1. Seal Kit for Brake Master Cylinder (Ref: ZZSP1975-5)
2. Return Spring - Leading Shoe 10" (Ref: 503981)
Return Spring - Brake Shoes 10
Return Spring - Leading Shoe 10" Ref: 503981
Application: Series 1, 2 & 3 with 10" brakes. Also Defender 90 to 1994.

Description: Upper pull-off spring operating on leading shoe only.

Approximate dimensions: overall length 126mm(5").

Price: 0.50 (0.60 Including VAT at 20%)




People who bought this item also bought:
1. Felt Seal for Series 1 Pedals (Ref: 70621)
2. Grommet Series 1 Pedals (Ref: 70620)
3. Seal Kit - front wheel cylinders (Ref: 275744)
Return Spring - Leading Shoe 10
Return Spring Front Brakes 11" Ref: 234889
Application: Series 2A and Series 3 with 11" diameter front brake drums.

Description: Pull-off spring for front brake shoes. Used on both standard width and wide (3") front brake shoes.

Approximate dimensions: overall length 105mm(4.1"), coil diameter 14.5mm(0.6")

Price: 0.80 (0.96 Including VAT at 20%)



Return Spring Front Brakes 11
Return Spring Lower 11" Rear Ref: 531893D
Application: Series 2A 109, Series 3 109 and Defender 110/130 to 1993.

Description: Replacement lower pull-off spring for 11" diameter drum brakes on rear axle.

Approximate dimensions: overall length 140mm(5.5")

Price: 0.85 (1.02 Including VAT at 20%)



Return Spring Lower 11
Return Spring Upper 11" Rear Ref: 548169D
Application: Series 2A 109, Series 3 109 and Defender 110/130 to 1993.

Description: Replacement upper pull-off spring for 11" diameter drum brakes on rear axle.

Approximate dimensions: overall length 180mm(7.1")

Price: 0.85 (1.02 Including VAT at 20%)



Return Spring Upper 11
Axle Set of Brake Shoes - 11 inch Rear Ref: STC2797DKIT
Axle set of 4 11inch brake shoes by Mintex plus 4x pull-off springs, 6x imperial brake drum screws and 2x metric brake drum screws.
Application: Rear axle on the following models, Series 2A LWB, Ser 3 LWB and Defender 110 to 1994.

Previous part numbers: RTC3418, STC359, GBS805

Price: 37.09 (44.51 Including VAT at 20%)



Axle Set of Brake Shoes - 11 inch Rear
Axle Set of Brake Shoes - 11" Front Ref: STC3944DKIT
Axle set of 4 11inch bonded brake shoes by Mintex box plus 4x pull-off springs and 6x brake drum screws.

Application: Front axle on the following models, Series 2A LWB 4cyl and Ser 3 LWB 4cyl.

Previous part numbers for shoes: RTC3417, GBS729

Price: 31.95 (38.34 Including VAT at 20%)




People who bought this item also bought:
1. Snail Cam Replacement Kit (Ref: RTC3176D)
2. Radiator Cap 7lb (Ref: 217437)
3. Locker for Hub Nuts (Ref: 217353=)
Axle Set of Brake Shoes - 11
Digital Dispensary > REGULAR Service and Repair Parts > Braking Systems > Drums and shoes. Discs and pads.
Page:  1  2  3  4   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Piston Assembly 2.4TDCI

Piston Assembly 2.4TDCI

122.63

Application: Defender from 2007 to 2012 with 2.4 litre TDCI engine.

Description: Standard size piston for 89.90mm bore. Supplied with rings, gudgeon pin and circlips. Made by Nural a Federal Mogul company.



find out more

Electric Fuel Pump - Series 1

Electric Fuel Pump - Series 1

100.44

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Repair Kit for Handbrake Adjuster

Repair Kit for Handbrake Adjuster

4.45

Application: Series 2A and Series 3.

Description: Old stock Lucas Girling repair kit for handbrake adjuster. Includes adjusting screw and wedges plus period tube of brake grease.


find out more

Injector for BMW M57 Diesel Engine

Injector for BMW M57 Diesel Engine

183.77

Application: Range Rover L322 with BMW M57 3.0litre diesel engine.

Description: Reconditioned Bosch injector for the M57 engine. Outright purchase, we do not need your old injector in vexchange.

Approximate dimensions: Overall length 22cm(8.7").

find out more

Bearing and Seals kit for Freelander 1 IRD

Bearing and Seals kit for Freelander 1 IRD

72.54

Application: Freelander 1 IRD unit except V6 model.

Description: Set of 7 OE spec bearings and 4 seals to overhaul the intermediate reduction drive unit. This kit does not include the plate for the oil cooler.

find out more

Rear Diff Repair Kit - Freelander2

Rear Diff Repair Kit - Freelander2

103.14

Application: Freelander 2 and Evoque

Description: Repair kit of OE bearings and seals for the rear differential. Kit includes 4x taper roller bearings, 3x oil seals, 2x 'O' rings, collapsible spacer and pinion nut.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -