Digital Dispensary

Product Sections


Best Sellers

Brass Nut 5/16"BSF

Brass Nut 5/16

1.66

Application: Series1 exhaust manifold.

Description: Brass nut 5/16"BSF for holding downpipe to exhaust manifold.

Approximate dimensions: 3/8"(9.5mm) high, 17/32"(13.5mm) across flats.

find out more

Stud for Exhaust Manifold

Stud for Exhaust Manifold

1.85

Application: Series 1 1.6 and 2.0 litre, Series 2 2 litre.

Description: Stud to hold downpipe to exhaust manifold.

Approximate dimesions: 5/16"BSF threads to both ends, overall length 1.25"(32mm)

find out more

Gasket Exhaust Manifold to Down Pipe

Gasket Exhaust Manifold to Down Pipe

0.96

Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.
find out more

Rubber Peg for Wiper Blade

Rubber Peg for Wiper Blade

0.95

Application: Series 1 1948 to 1958.

Decription: Rubber peg for retaining wiper blade to wiper arm.

Approximate dimensions: overall length 20.5mm(0.8")
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Brake Master Cylinder and Conversion Kit

Brake Master Cylinder and Conversion Kit

121.20

Application: Series 1 from 1954 to 1958 with 3/16" diameter brake pipes.

Description: Early Series 2 brake master cylinder and conversion kit to allow it to be fitted to Series 1.


Back in stock.
find out more

Clutch Plate 9.5"

Clutch Plate 9.5

45.16

Application: Series 2A (optional use) and Series 3.

Description: 9.5" diameter clutch plate (friction disc) by AP Driveline (HB8117). 10 spline centre.

Approximate dimensions: overall diameter 240mm.

find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Grommet for Steering Column

Grommet for Steering Column

13.26

Application: Sewries 1.

Description: Reproduction lLarge grommet in bulkhead for steering column.

Approximate dimensions: Overall diameter 92mm(3.6"), column hole diameter 31mm(1.2").

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > REGULAR Service and Repair Parts > Braking Systems > Drums and shoes. Discs and pads.
Page:   <<   <  1  2  3  4
Mintex Front Brake Pad Set Ref: STC9191D
Application: Discovery 1 front brakes with solid discs from approximately 1995. Where pads are retained by solid pins through holes in pads.
Description: Set of four Mintex brake pads, set number MLB115. Not supplied with fitting kit. See STC8576 and RTC5001
Approximate dimensions: each pad measures 105mm (4.13") by 73mm (2.87").

Price: 16.00 (19.20 Including VAT at 20%)



Mintex Front Brake Pad Set
Mintex Front Brake Pads Ref: SFP000260D
Application: Defender 90/110/130 front axle 1994 onwards.

Description: Mintex MLB114 axle set of brake pads. No fitting kit supplied - see RTC5001 & STC8576.

Approximate dimensions: each pad measures 126mm (4.96") long x 69mm (2.72") high.

Price: 16.00 (19.20 Including VAT at 20%)



Mintex Front Brake Pads
Brake Pad Fitting Kit Ref: RTC5001
Application: Discovery 1 front brakes with solid discs from approximately 1995. Defnder front pads from 1995 with solid discs. Where pads are retained by solid pins through holes in pads.

Description: Set of four solid pins and 4 small split pins.

Approximate dimensions: eachsolid pin is 84mm (3.3") long and diameter of 6.5mm (0.26").

Price: 3.00 (3.60 Including VAT at 20%)



Brake Pad Fitting Kit
Brake Pad Fitting Kit - Front Discs Ref: STC8573
Application: Front axles of the following vehicles with solid discs. Range Rover Classic 1972 to 1989, Discovery 1 to 1993, Defender 90 to 1993.

Description: Set of 4 split pins and 4 springs.

Approximate dimensions: Each split pin is 53mm (2.08") long and 4.5mm (0.18") in diameter. Each spring is 52mm (2.05") long.

Price: 2.38 (2.86 Including VAT at 20%)



Brake Pad Fitting Kit - Front Discs
Brake Pad Fitting Kit Ref: STC8574
Application: Rear brake pads on Range Rover Classic 1972 to 1995, Discovery 1 1989 to 1998, Defender 90 1995 onwards.

Description: Set of 4x split pins and 4x spring clips.

Approximate dimensions: split pins are 75mm (2.95") long and 3.5mm (0.14") in diameter.

Price: 2.20 (2.64 Including VAT at 20%)



Brake Pad Fitting Kit
Brake Pad Fitting Kit - Front Axle Ref: STC8575
Application: Use with STC9190D, Mintex front brake pads on Range Rover Classic 1990 to 1995 and Discovery 1 where fitted with vented discs.

Description: Brake pad fitting kit comprising 4x solid pins, 4x small split pins and 4x springs.

Approximate dimensions: Each pin is 95mm (3.74") long and 6.3mm (0.25") in diameter.

Price: 3.00 (3.60 Including VAT at 20%)



Brake Pad Fitting Kit - Front Axle
Brake Pad Fitting Kit Ref: STC8576
Application: Discovery 1 front brakes with solid discs from approximately 1995. Where pads are retained by solid pins through holes in pads.

Description: Fitting kit of 4 springs and 4 small split pins. Used with pin kit RTC5001.


Price: 3.00 (3.60 Including VAT at 20%)



Brake Pad Fitting Kit
Digital Dispensary > REGULAR Service and Repair Parts > Braking Systems > Drums and shoes. Discs and pads.
Page:   <<   <  1  2  3  4

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Speedo Cable S3 4cylinder

Speedo Cable S3 4cylinder

9.60

Application: Series3 models with 4 cylinder engines. Suitable for both left hand drive and right hand drive.

Description: Reproduction speedo drive cable.

Approximate dimensions: Overall length 2.49m(98")


find out more

Parts Catalogue Range Rover 1992 to 1995

Parts Catalogue Range Rover 1992 to 1995

43.38

Application: Range Rover Classic from 1992 to 1995. Covering the following engines - 3.9V8, 4.2V8, 2.5VM, 200TDi and 300TDi.

Description: Reprint by Brookland Books with 484 pages.

Approximate dimensions: 297mm(11.7") tall, 210mm(8.3") wide and 26mm(1") thick.

find out more

Engine Stop Transfer

Engine Stop Transfer

2.34

Application: Series 3 diesel.

Description: Transfer reading 'Pull engine stop fully out before switching off'. Fixed to inside of windscreen.

find out more

Regulator for 17ACR Alternator

Regulator for 17ACR Alternator

8.40

Application: Range Rover Classic when fitted with 17ACR alternator.

Description: Lucas voltage regulator for alternator.

Alternative part numbers: UCB100, 14TR, 37581D, 607887

find out more

Vacuum Unit - 45D type

Vacuum Unit - 45D type

26.40

Application: Series3 and early Defender when fitted with Lucas 45D distributor.

Description: Lucas vacuum advance unit.

Approximate dimensions: Overall lengty 67mm(2.6"), diaphragm diameter 55mm(2.2").

find out more

Low Gear Wheel

Low Gear Wheel

31.80

Application: Series 1 and Series 2 - suffix A & B only.

Description: Low gear wheel with 39 teeth on output shaft in transfer box. Photo shows gear still coated in original wax, not all stock will come in this state.

Approximate dimensions: Thicness 33mm(1.3"), inside diameter 57mm(2.2"), outside diameter 14.5cm(5.7").


find out more

Throttle Pedal - Series 2 and 3

Throttle Pedal - Series 2 and 3

29.76

Application: Series 2 and Series 3 models.

Description: Throttle pedal.

Approximate dimensions: Overall length 22.5cm(8.9"), width 32mm(1.25")

find out more

SU Fuel Pump - Electronic Negative Earth

SU Fuel Pump - Electronic Negative Earth

122.82

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump with electronics instead points control, but otherwise to original pattern. For mounting in engine bay. For use on negative earth vehicles only. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -