Digital Dispensary

Product Sections


Best Sellers

Gasket Set for Solex 32PBI-2 Carburettor

Gasket Set for Solex 32PBI-2 Carburettor

7.66

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.
Description: Set of 6 gaskets and 8 fibre washers for this carburettor
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Differential Pinion

Oil Seal Differential Pinion

5.21

Application: Series 1, 2 & 3 Rover type differentials.

Description: Oil seal to nose of differential. Corteco/Gaco boxed.

Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").

Original part number: 217507.
find out more

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Gasket for Differential to Axle Casing

Gasket for Differential to Axle Casing

0.60

Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Page:   <<   <  1  2  3  4  5   >   >>
Pair of Clips for Distributor Cap Ref: 502287
Application: Lucas 25D 4 cylinder ditributor as used on Series 2, Series 2A and Series 3.

Description: Nicely made reproduction clips for distributor cap. Sold as a pair.

Approximate dimensions: Overall length 77mm(3"), width 9mm(0.35")

Lucas part number: 421824

Price: 10.00 (12.00 Including VAT at 20%)



Pair of Clips for Distributor Cap
Rotor Arm Ref: 261242
Application: Series 1 1600petrol with Lucas D3A4 or DVX4A distributor.

Description: Reproduction rotor arm.

Approximate dimensions: Overal length 43.5mm(1.8"), height 17mm(0.66")

Lucas part number: 408355

Price: 11.58 (13.90 Including VAT at 20%)




People who bought this item also bought:
1. Gasket Inlet Manifold to Cylinder Head (Ref: 9179)
2. Gasket Water Branch to Cylinder Head (Ref: 210447)
3. Gasket Inlet Pipe to Water Pump (Ref: 213724)
Rotor Arm
Rotor Arm Lucas 25D Ref: RTC3612
Application: Lucas 25D 4cylinder distributor as fitted to Series 2A and early Series 3 petrol engines. Also applicable to the DM2 distributor to Series 1 1954 to 1958.

Description: Reproduction rotor arm.

Approximate dimensions: shaft diameter 14.5mm (0.57 inches), height 16.5mm (0.65 inches)

Lucas part number: 460051

Price: 8.00 (9.60 Including VAT at 20%)



Rotor Arm Lucas 25D
Red Rotor Arm for Lucas 25D Ref: RTC3612R
Application: Lucas 25D 4cylinder distributor as fitted to Series 2A and early Series 3 petrol engines. Also applicable to the DM2 distributor to Series 1 1954 to 1958.

Description: Reproduction rotor arm. Modelled on the original, dependable 1960's design, but made from modern materials on the latest machinery to very close tolerances.
These 100% LUCAS COMPATIBLE RED ROTOR ARMS* will not let you down.
The integrally moulded brass inlay dispenses with the troublesome rivet used on most versions which is known to short circuit.
The increased insulation properties of the body makes them suitable for use with high voltage coils & electronic ignition kits.
The spring steel clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit, even on old & slightly reduced diameter mountings.

Approximate dimensions: shaft diameter 14.5mm (0.57 inches), height 16.5mm (0.65 inches)

Lucas part number: 460051

Price: 6.00 (7.20 Including VAT at 20%)



Red Rotor Arm for Lucas 25D
Rotor Arm Lucas 45D Ref: RTC3614
Application: Lucas 45D 4cylinder distributor as fitted to Series 3 petrol engines.

Description: Lucas boxed rotor arm.

Approximate dimensions: shaft diameter 14.5mm (0.57 inches), height 20mm (0.79 inches)

Lucas part number: 54422803

Price: 2.20 (2.64 Including VAT at 20%)



Rotor Arm Lucas 45D
Red Rotor Arm for Lucas 45D Ref: RTC3614R
Application: Lucas 45D 4cylinder distributor as fitted to Series 3 petrol engines.

Description: Reproduction rotor arm. Modelled on the original, dependable 1960's design, but made from modern materials on the latest machinery to very close tolerances.
These 100% LUCAS COMPATIBLE RED ROTOR ARMS* will not let you down.
The integrally moulded brass inlay dispenses with the troublesome rivet used on most versions which is known to short circuit.
The increased insulation properties of the body makes them suitable for use with high voltage coils & electronic ignition kits.
The spring steel clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit, even on old & slightly reduced diameter mountings.

Approximate dimensions: shaft diameter 14.5mm (0.57 inches), height 20mm (0.79 inches)

Lucas part number: 54422803

Price: 6.00 (7.20 Including VAT at 20%)



Red Rotor Arm for Lucas 45D
Rotor Arm Lucas 6 Cylinder Ref: RTC4542
Application: Series 2A and Series 3, 6 cylinder petrol with Lucas 25D6 distributor and Lucas 45D6.

Description: Replacement rotor arm.

Previous part numbers: GRA102, 262704

Lucas Part number: 418726

Price: 2.00 (2.40 Including VAT at 20%)



Rotor Arm Lucas 6 Cylinder
Red Rotor Arm for 6 cylinder Distributor Ref: RTC4542R
Application: Series 2A and Series 3, 6 cylinder petrol with Lucas 25D6 distributor and Lucas 45D6.

Description: Replacement rotor arm. Modelled on the original, dependable 1960's design, but made from modern materials on the latest machinery to very close tolerances.
These 100% LUCAS COMPATIBLE RED ROTOR ARMS* will not let you down.
The integrally moulded brass inlay dispenses with the troublesome rivet used on most versions which is known to short circuit.
The increased insulation properties of the body makes them suitable for use with high voltage coils & electronic ignition kits.
The spring steel clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit, even on old & slightly reduced diameter mountings.

Previous part numbers: GRA102, 262704

Lucas Part number: 418726

Price: 6.00 (7.20 Including VAT at 20%)



Red Rotor Arm for 6 cylinder Distributor
Rotor Arm Ducellier Ref: RTC4933
Application: Ducellier 4cylinder distributor as fitted to Series 3 petrol engines and some Defender models.

Description: Intermotor brand rotor arm. Now comes in red rather than the blue in photo.

Approximate dimensions: shaft diameter 14.5mm (0.57 inches), height 36.5mm (1.44 inches)

Price: 1.77 (2.12 Including VAT at 20%)



Rotor Arm Ducellier
Rotor Arm Lucas V8 Ref: STC1857
Application: Electronic ignition versions of Lucas V8 Distributor.
Description: Portugues made rotor arm supposedly on original Lucas tooling. (Original Lucas item is no longer available and these are no longer in production).
Approximate dimensions: length 70.5mm (2.8"), height 24.2mm (0.95"), spindle diameter 14.6mm (0.57").

Price: 12.40 (14.88 Including VAT at 20%)




People who bought this item also bought:
1. Distributor Cap Lucas V8 (Ref: STC8368)
2. Float for CD175 (Ref: 605833)
3. Clutch Slave Cylinder - R380 Gearbox (Ref: FTC5072)
Rotor Arm Lucas V8
Page:   <<   <  1  2  3  4  5   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Outer Pinion Bearing

Outer Pinion Bearing

10.72

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for outer end of differential pinion gear. Timken bearing numbers HM88046/HM88010

Approximate dimensions: Outside diameter 2.7"(68.5mm), inside diameter 1.25"(31.8mm)., height 0.93"(23.5mm).


find out more

Inner Pinion Bearing - Differential

Inner Pinion Bearing - Differential

21.70

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for inner end of differential pinion gear. Timken bearing numbers HM801346X/HM801310

Approximate dimensions: Outside diameter 3.25"(82.5mm), inside diameter 1.5"(38mm)., height 1.22"(31mm).

find out more

Seal Kir for 1 1/8" Wheel Cylinders

Seal Kir for 1 1/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for rear wheel cylinders with bore of 1 1/8"(28.5mm). Kit has sufficient seals for both front wheel cylinders.

find out more

Seal Kit for 1 3/8" Wheel Cylinders

Seal Kit for 1 3/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for front wheel cyliders with bore of 1 3/8"(35mm). Kit has sufficient seals for both front wheel cylinders.


find out more

Outlet Nozzle - SU Fuel Pump

Outlet Nozzle - SU Fuel Pump

4.44

Application: Series 1 and early Series 2 models.

Description: Nozzle for outlet of SU fuel pumps. Allows push-on fuel hose connection to pump.

Approximate dimensions: Thread diameter 22mm(0.87"), nozzle diameter 7mm(0.28").

find out more

Wiper Arm Series 3 RH

Wiper Arm Series 3 RH

24.25

Application: Series3 models.

Description: Right hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -