Digital Dispensary

Product Sections


Best Sellers

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Seal Kit for Brake Master Cylinder

Seal Kit for Brake Master Cylinder

19.80

Application: Series One from 1948 to 1958.
Description: Reproduction seal kit for brake master cylinder. Suits all short wheel base models. Not suitable for long wheel base models.
Original part number 278524
find out more

Anchor Plate for 10inch brake shoes

Anchor Plate for 10inch brake shoes

8.44

Anchor plate for use with 10inch brakes - see kit above. One anchor plate is used with each pair of shoes. These do not need replacing with every change of brake shoes, but they do become worn over several years use. Sold singly.
Approximate dimensions: 78mm x 45mm x 5mm.

Application: see STC2796DKIT above.
find out more

Felt Seal Stub Shaft to Drive Flange

Felt Seal Stub Shaft to Drive Flange

0.48

Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
find out more

Inner Wheel Hub Seal

Inner Wheel Hub Seal

4.28

Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Split Pin - Shocker Retention

Split Pin - Shocker Retention

0.25

Application: Series 1, Series 2 and Series 3.

Description: Replacement split pin for retaining shock absorber to bottom plate of spring.

Approximate dimensions: Overall length 55.5mm(2.2"), diameter 6mm(0.24")

find out more

Dust Cap for Bleed Screw

Dust Cap for Bleed Screw

0.30

Application: Suitable for all bleed screws.
Description: Soft plastic dust cap for bleed screws.
Approximate dimensions: length 15mm(0.6"), diameter 8mm (0.3")
Original part number 234957
find out more

Screw for retaining Brake Drums

Screw for retaining Brake Drums

0.25

Application: Series 1, 2 & 3.
Description: Countersunk head screw 3/8"BSW by 5/8" long.
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Cooling System for Land Rover Series 2 and 3
Page:  1  2   >   >>
Heater Control Valve Ref: 88G588L
Application: Series 2 & 2A.

Description: Reproduction brass control valve for heater on the above models.

Price: 15.00 (18.00 Including VAT at 20%)




People who bought this item also bought:
1. Manual Washer Pump (Ref: RTC3639)
2. Lock Nut for Hub Bearing (Ref: FRC8700D)
3. Clip for Handbrake Expander Unit (Ref: 515927)
Heater Control Valve
Replacement Heater Valve Series 3 Ref: 90577299
Application: Series 3 with 4 cylinder and 6 cylinder engines.

Description: Reproduction heater control valve.

Approximate dimensions: Height 84mm(3.3")

Price: 17.50 (21.00 Including VAT at 20%)



Replacement Heater Valve Series 3
Top Hose Series 3 4 cylinder Ref: 577346=
Application: Series 3 2.25 litre engines, both petrol and diesel. Also applicable to Series 2A four cylinder models which are fitted with the later radiator with narrow header tank.
Description: Top hose between radiator and engine..
Approximate dimensions: internal diameter 30.5mm (1. 3/16 inches), length around curve 27cm (10.5 inches).

Price: 3.50 (4.20 Including VAT at 20%)



Top Hose Series 3 4 cylinder
Bypass hose Series 2A and Series 3 Ref: 574871=
Application: Series 2A and Series 3 2.25 litre engines, both petrol and diesel.
Description: Replacement hose between water pump and thermostat housing.
Approximate dimensions: internal diameter 30.5mm (1.3/16 inches), length 95mm (3.75 inches).

Price: 0.90 (1.08 Including VAT at 20%)



Bypass hose Series 2A and Series 3
Bottom Hose Series 3 Ref: NRC3115=
Application: Series 3 2.25 litre engines, both petrol and diesel. Also applicable to Series 2A four cylinder models which are fitted with the later radiator with narrow header tank.
Description: Replacement bottom hose between radiator and engine..
Approximate dimensions: internal diameter 33.5mm (1. 5/16 inches), length around curve 33cm (13 inches).

Price: 3.50 (4.20 Including VAT at 20%)



Bottom Hose Series 3
Heater Hose Ref: 234063
Application: Series I and Series 2 1948 to 1967 when fitted with heater.

Description: Replacement heater hose.

Approximate dimensions: Internal diameter 7/16"(11.5mm), outside diameter 21mm(0.8"), overall length 124mm(4.9").

Price: 7.45 (8.94 Including VAT at 20%)



Heater Hose
Replacement Heater Hoses S3 RHD Ref: HEATERHOSEKIT01
Application: Series 3 4 cylinder petrol (gasolene) and diesel, right hand drive.
Description: Set of 3 hoses and 6 hose clips. Hose part numbers 577292, 594629 & 594632.

Price: 7.50 (9.00 Including VAT at 20%)




People who bought this item also bought:
1. Vacuum Pipe Straight Connector (Ref: 574878)
Replacement Heater Hoses S3 RHD
Replacement Heater Hoses S3 LHD Ref: HEATERHOSEKIT02
Application: Series 3 4 cylinder petrol (gasolene) and diesel, left hand drive.
Description: Set of 4 hoses and 8 hose clips. Hose part numbers 2x 577292, 594629 & 594636.

Price: 8.95 (10.74 Including VAT at 20%)



Replacement Heater Hoses S3 LHD
Thermostat 74 degrees Ref: 532453
Application: Series 2A and Series 3 2.25 litre engines, both petrol and diesel.

Description: This is the cooler 'Summer' option, it is of replacement manufacture.

Approximate dimensions: overall diameter 53.5mm, height 42mm.

Price: 4.00 (4.80 Including VAT at 20%)



Thermostat 74 degrees
Thermostat 82 degrees Ref: 596225
Application: Series 2A and Series 3 2.25 litre engines, both petrol and diesel.

Description: This is the hotter 'Winter' option, it is genuine Land Rover.

Approximate dimensions: overall diameter 53.5mm, height 41mm.

Price: 2.57 (3.08 Including VAT at 20%)




People who bought this item also bought:
1. Bush for Front Stub Axle (Ref: 217354)
Thermostat 82 degrees
Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Cooling System for Land Rover Series 2 and 3
Page:  1  2   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Piston Assembly 2.4TDCI

Piston Assembly 2.4TDCI

122.63

Application: Defender from 2007 to 2012 with 2.4 litre TDCI engine.

Description: Standard size piston for 89.90mm bore. Supplied with rings, gudgeon pin and circlips. Made by Nural a Federal Mogul company.



find out more

Electric Fuel Pump - Series 1

Electric Fuel Pump - Series 1

100.44

Application: Series 1 Land Rovers 1948 to 1958. Series 2 with 2 litre petrol engine.

Description: Authentic SU electric fuel pump to original pattern. For mounting in engine bay. Can be used on either positive or negative earth vehicles. NB Both outlet and inlet have threaded connectors.

Approximate dimensions: 14cm long, base diameter 73mm. Mounting holes in base are threaded M6

find out more

Repair Kit for Handbrake Adjuster

Repair Kit for Handbrake Adjuster

4.45

Application: Series 2A and Series 3.

Description: Old stock Lucas Girling repair kit for handbrake adjuster. Includes adjusting screw and wedges plus period tube of brake grease.


find out more

Injector for BMW M57 Diesel Engine

Injector for BMW M57 Diesel Engine

183.77

Application: Range Rover L322 with BMW M57 3.0litre diesel engine.

Description: Reconditioned Bosch injector for the M57 engine. Outright purchase, we do not need your old injector in vexchange.

Approximate dimensions: Overall length 22cm(8.7").

find out more

Bearing and Seals kit for Freelander 1 IRD

Bearing and Seals kit for Freelander 1 IRD

72.54

Application: Freelander 1 IRD unit except V6 model.

Description: Set of 7 OE spec bearings and 4 seals to overhaul the intermediate reduction drive unit. This kit does not include the plate for the oil cooler.

find out more

Rear Diff Repair Kit - Freelander2

Rear Diff Repair Kit - Freelander2

103.14

Application: Freelander 2 and Evoque

Description: Repair kit of OE bearings and seals for the rear differential. Kit includes 4x taper roller bearings, 3x oil seals, 2x 'O' rings, collapsible spacer and pinion nut.
find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -