Digital Dispensary

Product Sections


Best Sellers

Brass Nut 5/16"BSF

Brass Nut 5/16

1.66

Application: Series1 exhaust manifold.

Description: Brass nut 5/16"BSF for holding downpipe to exhaust manifold.

Approximate dimensions: 3/8"(9.5mm) high, 17/32"(13.5mm) across flats.

find out more

Stud for Exhaust Manifold

Stud for Exhaust Manifold

1.85

Application: Series 1 1.6 and 2.0 litre, Series 2 2 litre.

Description: Stud to hold downpipe to exhaust manifold.

Approximate dimesions: 5/16"BSF threads to both ends, overall length 1.25"(32mm)

find out more

Gasket Exhaust Manifold to Down Pipe

Gasket Exhaust Manifold to Down Pipe

0.96

Application: Series 1, 2 & 3 four cylinder engines.
Description: Square flange gasket for exhaust. Used on various exhaust manifolds and on some pipe to pipe exhaust joints.
find out more

Rubber Peg for Wiper Blade

Rubber Peg for Wiper Blade

0.95

Application: Series 1 1948 to 1958.

Decription: Rubber peg for retaining wiper blade to wiper arm.

Approximate dimensions: overall length 20.5mm(0.8")
find out more

Sealing Ring Water Pump to Cylinder Head

Sealing Ring Water Pump to Cylinder Head

2.18

Application: Series 1 1.6ltr & 2.0Ltr and Series 2A/3 2.6ltr petrol engines.
Description: Thick rubber sealing ring between water pump and cylinder head.
Approximate dimensions: internal diameter 13mm (1/2"), outside diameter 24mm (0.95"), thickness 5.3mm (0.2")
find out more

Brake Master Cylinder and Conversion Kit

Brake Master Cylinder and Conversion Kit

121.20

Application: Series 1 from 1954 to 1958 with 3/16" diameter brake pipes.

Description: Early Series 2 brake master cylinder and conversion kit to allow it to be fitted to Series 1.


Back in stock.
find out more

Clutch Plate 9.5"

Clutch Plate 9.5

45.16

Application: Series 2A (optional use) and Series 3.

Description: 9.5" diameter clutch plate (friction disc) by AP Driveline (HB8117). 10 spline centre.

Approximate dimensions: overall diameter 240mm.

find out more

Copper Ring Water Pump to Thermostat Housing

Copper Ring Water Pump to Thermostat Housing

7.44

Application: Series One with 1.6 or 2 litre petrol engine. Series Two with 2 litre petrol engine.
Description: Copper ring to support 'O' ring between water pump and thermostat housing.
Approximate dimensions: outside diameter 16mm(0.63"), inside diameter 11mm(0.43"), height 7.5mm(0.3")
find out more

Grommet for Steering Column

Grommet for Steering Column

13.26

Application: Sewries 1.

Description: Reproduction lLarge grommet in bulkhead for steering column.

Approximate dimensions: Overall diameter 92mm(3.6"), column hole diameter 31mm(1.2").

find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Body Parts for Series 2 and 3
Page:  1  2  3   >   >>
Bonnet Rest Strip Ref: 300824A
Application: Series1, Series2 and Series3.
Description: Original style woven cotton bonnet rest strip, sold by the metre.

Price: 7.50 (9.00 Including VAT at 20%)




People who bought this item also bought:
1. Set of Rivets for Bonnet Strip (Ref: 68087x12)
2. Gaiter for Main Gear Lever (Ref: 301437A)
3. Spring High/Low Selector Shaft (Ref: 217445)
Bonnet Rest Strip
Gaiter for High/Low Gear Lever Ref: 338871=
Application: Series 1, Series 2/2A and Series 3.

Description: Reproduction rubber gaiter for the high/low gear lever.

Approximate dimensions: Overall length 143mm, height 90mm.

Price: 2.05 (2.46 Including VAT at 20%)




People who bought this item also bought:
1. Buffer for Door (Ref: 304110)
2. Spring High/Low Selector Shaft (Ref: 217445)
3. Blanking Gommet for Bell Housing (Ref: 232604)
Gaiter for High/Low Gear Lever
Retainer and Fixings for Hi/Lo Gaiter Ref: 303817KIT
Application: Series 1, Series 2/2A and Series 3.

Description: Retainer for gaiter plus 3 screws(79048) and 3 spire nuts (302532).

Approximate dimensiions: Length 11.4cm(4.5"), upstand 2.1cm(0.83"), width 8.1cm(3.2")

Price: 8.50 (10.20 Including VAT at 20%)




People who bought this item also bought:
1. Gaiter for High/Low Gear Lever (Ref: 338871=)
2. Spring High/Low Selector Shaft (Ref: 217445)
3. Blanking Gommet for Bell Housing (Ref: 232604)
Retainer and Fixings for Hi/Lo Gaiter
Gaiter for Handbrake Lever Ref: 338780
Application: Late Series 2A and Series 3.

Description: Reproduction rubber gaiter for handbrake lever. This is for the later style lever that curves upwards to nearly vertical.

Approximate dimensions: Height 168mm(6.6"), depth 110mm(4.3")

Price: 2.25 (2.70 Including VAT at 20%)



Gaiter for Handbrake Lever
Gaiter for Main Gear Lever Ref: 301437A
Application: Series 1, Series 2, Series 2A and Series 3 4 & 6 cylinder models.

Description: Reproduction rubber gaiter for main gear lever.

Approximare dimensions: 11.5cm(4.5") square, 3.6cm(1.4") high.

Price: 1.80 (2.16 Including VAT at 20%)




People who bought this item also bought:
1. Gaiter for High/Low Gear Lever (Ref: 338871=)
2. Spring High/Low Selector Shaft (Ref: 217445)
3. Blanking Gommet for Bell Housing (Ref: 232604)
Gaiter for Main Gear Lever
Rubber Grommet Ref: 334189
Application: Series 2A and Series 3.

Description: Domed rubber grommet for tunnel panel.

Approximate dimensions: to suit 79mm(3.125") diameter hole, overall diameter 101mm(4"), height 23mm.

Price: 3.45 (4.14 Including VAT at 20%)




People who bought this item also bought:
1. Thrust Washer Intermediate Gear Cluster (Ref: 521328)
2. Mainshaft Nut (Ref: 217477)
Rubber Grommet
Hinge Pin Kit Ref: 330953/7
Application: Series 2a door hinges front and rear. Series 3 and early Defender rear end door hinges.

Description: Kit to replace the hinge pin. Kit contains plated steel bolt, nut, spring and locker together with brass centre ball.

Approximate dimensions: Overall length 63mm(2.5").

Price: 0.94 (1.13 Including VAT at 20%)




People who bought this item also bought:
1. High Torque Starter Motor (Ref: RTC5225HT)
Hinge Pin Kit
Set of 4 S/S Hinge Pins for Dash Vents Ref: 334121SS
Application: Late Series 2A, Series 3 and Defender to 2007.

Description: Set of 4 stainless steel hinge pins with domed stainless stell nuts for the dash venilators.

Approximate dimensions: Overall length 95mm(3.86"), pin diameter 3/16"(4.6mm)

Price: 18.38 (22.06 Including VAT at 20%)



Set of 4 S/S Hinge Pins for Dash Vents
Reproduction Land Rover Badge Series1 Ref: 332670B
Badge "Land Rover Birmingham, England".
Reproduction badge in cast aluminium.
Approximate dimensions: 183mm x 71mm.

Price: 16.86 (20.23 Including VAT at 20%)



Reproduction Land Rover Badge Series1
Reproduction Land Rover Badge S1 and S2 Ref: 332670S
Badge "Land Rover Solihull, Warwickshire, England".
Reproduction badge in cast aluminium.

Approximate dimensions: 183mm x 71mm.


Price: 16.86 (20.23 Including VAT at 20%)



Reproduction Land Rover Badge S1 and S2
Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Body Parts for Series 2 and 3
Page:  1  2  3   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Door Mirror Right Hand

Door Mirror Right Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Speedo Cable S3 4cylinder

Speedo Cable S3 4cylinder

9.60

Application: Series3 models with 4 cylinder engines. Suitable for both left hand drive and right hand drive.

Description: Reproduction speedo drive cable.

Approximate dimensions: Overall length 2.49m(98")


find out more

Parts Catalogue Range Rover 1992 to 1995

Parts Catalogue Range Rover 1992 to 1995

43.38

Application: Range Rover Classic from 1992 to 1995. Covering the following engines - 3.9V8, 4.2V8, 2.5VM, 200TDi and 300TDi.

Description: Reprint by Brookland Books with 484 pages.

Approximate dimensions: 297mm(11.7") tall, 210mm(8.3") wide and 26mm(1") thick.

find out more

Engine Stop Transfer

Engine Stop Transfer

2.34

Application: Series 3 diesel.

Description: Transfer reading 'Pull engine stop fully out before switching off'. Fixed to inside of windscreen.

find out more

Regulator for 17ACR Alternator

Regulator for 17ACR Alternator

8.40

Application: Range Rover Classic when fitted with 17ACR alternator.

Description: Lucas voltage regulator for alternator.

Alternative part numbers: UCB100, 14TR, 37581D, 607887

find out more

Vacuum Unit - 45D type

Vacuum Unit - 45D type

26.40

Application: Series3 and early Defender when fitted with Lucas 45D distributor.

Description: Lucas vacuum advance unit.

Approximate dimensions: Overall lengty 67mm(2.6"), diaphragm diameter 55mm(2.2").

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -