Digital Dispensary

Product Sections


Best Sellers

Gasket Set for Solex 32PBI-2 Carburettor

Gasket Set for Solex 32PBI-2 Carburettor

7.66

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.
Description: Set of 6 gaskets and 8 fibre washers for this carburettor
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Differential Pinion

Oil Seal Differential Pinion

5.21

Application: Series 1, 2 & 3 Rover type differentials.

Description: Oil seal to nose of differential. Corteco/Gaco boxed.

Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").

Original part number: 217507.
find out more

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Gasket for Differential to Axle Casing

Gasket for Differential to Axle Casing

0.60

Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Axles and Propshafts for Land Rover Series 2 and 3
Page:   <<   <  6
Replacement Drive Flange 10 Spline Ref: 571235D
Application: Series 1 and Series 2 - all models. Series 3 short wheel base models to mid 1980.

Description: Replacement 10 spline drive flange.

Approximate dimensions: Overall diameter 11.4cm(4.5"), height 50mm(2").

Old part number 217378.

Price: 8.50 (10.20 Including VAT at 20%)




People who bought this item also bought:
1. Felt Seal Stub Shaft to Drive Flange (Ref: RTC3515)
2. Inner Wheel Hub Seal (Ref: RTC3510)
3. Oil Seal Differential Pinion (Ref: FRC4586)
Replacement Drive Flange 10 Spline
Drive Flange 24spline Ref: 571711
Application: Series 3 88" from 07/1980 and Series 3 109".

Description: Original equipment specification drive flange with 24 splines.

Approximate dimensions: Overall diameter 11.3cm(4.4"), height 4.95cm(1.9")

Price: 13.50 (16.20 Including VAT at 20%)



Drive Flange 24spline
Replacement Drive Flange 24spline Ref: 571711D
Application: Series 3 88" from 07/1980 and Series 3 109".

Description: Replacement drive flange with 24 splines.

Approximate dimensions: Overall diameter 11.3cm(4.4"), height 4.95cm(1.9")

Price: 6.00 (7.20 Including VAT at 20%)



Replacement Drive Flange 24spline
Stud for wheel Nut Ref: 561590D
Application: Series 2 and 2A wheel hubs.

Description: Threaded stud 9/16" BSF x overall length of 43mm (1.6"). Short thread 12mm(0.47"), long thread 20mm(0.79"). Used with nut 561254



Price: 0.76 (0.91 Including VAT at 20%)




People who bought this item also bought:
1. Axle Set of Brake Shoes - 10" (Ref: STC2796DKIT)
2. Washer Shock Absorber Bush (Ref: RYF500160)
3. Bolt - Shock Absorber Fixing (Ref: NRC7064)
Stud for wheel Nut
Stud for Wheel Nut Ref: 561886
Application: Series 2A.

Description: Replacement splined stud for wheel nuts. Threaded 9/16"BSF. These can be used to replace the standard threaed studs in hubs where the thread is damaged or has pulled out.

Approximate dimensions: Overall length 42.6mm(1.7"), splines outside diameter 15mm(0.6").

Price: 0.65 (0.78 Including VAT at 20%)



Stud for Wheel Nut
Stud for Wheel Nut Ref: 576825A
Application: Very late Series 2A and Series 3.

Description: Replacement splined wheel stud. Threaded M16 x 0.7mm.

Approximate dimensions: Overall length 42mm(1.65"), splines outside diameter 16.4mm(0.65")

Price: 0.48 (0.58 Including VAT at 20%)



Stud for Wheel Nut
Wheel Nut Ref: 561254
Application: Series 2A.

Description: Replacement single taper wheel nut for 9/16BSF studs.

Approximate dimensions: Across flats 23.9mm(15/16"), height 16mm(5/8").



Price: 0.65 (0.78 Including VAT at 20%)



Wheel Nut
Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Axles and Propshafts for Land Rover Series 2 and 3
Page:   <<   <  6

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Outer Pinion Bearing

Outer Pinion Bearing

10.72

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for outer end of differential pinion gear. Timken bearing numbers HM88046/HM88010

Approximate dimensions: Outside diameter 2.7"(68.5mm), inside diameter 1.25"(31.8mm)., height 0.93"(23.5mm).


find out more

Inner Pinion Bearing - Differential

Inner Pinion Bearing - Differential

21.70

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for inner end of differential pinion gear. Timken bearing numbers HM801346X/HM801310

Approximate dimensions: Outside diameter 3.25"(82.5mm), inside diameter 1.5"(38mm)., height 1.22"(31mm).

find out more

Seal Kir for 1 1/8" Wheel Cylinders

Seal Kir for 1 1/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for rear wheel cylinders with bore of 1 1/8"(28.5mm). Kit has sufficient seals for both front wheel cylinders.

find out more

Seal Kit for 1 3/8" Wheel Cylinders

Seal Kit for 1 3/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for front wheel cyliders with bore of 1 3/8"(35mm). Kit has sufficient seals for both front wheel cylinders.


find out more

Outlet Nozzle - SU Fuel Pump

Outlet Nozzle - SU Fuel Pump

4.44

Application: Series 1 and early Series 2 models.

Description: Nozzle for outlet of SU fuel pumps. Allows push-on fuel hose connection to pump.

Approximate dimensions: Thread diameter 22mm(0.87"), nozzle diameter 7mm(0.28").

find out more

Wiper Arm Series 3 RH

Wiper Arm Series 3 RH

24.25

Application: Series3 models.

Description: Right hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -