Digital Dispensary

Product Sections


Best Sellers

Gasket Set for Solex 32PBI-2 Carburettor

Gasket Set for Solex 32PBI-2 Carburettor

7.66

Application: Series 1 2.0litre engine 1952 to 1958 fitted with Solex 32PBI-2 carburettor.
Description: Set of 6 gaskets and 8 fibre washers for this carburettor
find out more

Clip for brake pipe grommet

Clip for brake pipe grommet

0.61

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Clip for brake pipe support grommet 6860L. Used on rear axle casing on all Series models from 1954 to 1984.
Approximate dimensions: 11mm(7/16") wide, 34mm(1.3") long, mounting hole 5mm(0.2") diameter, internal diameter of clip when closed 13mm.
find out more

Grommet - Brake Pipe Support

Grommet - Brake Pipe Support

0.31

Application: Series 1 1954 to 1958, Series 2 and Series 3.
Description: Grommet to support brake pipe on rear axle casing. Used with clip 56666.
Approximate dimensions: overall length 21.5mm(0.85"), inside diameter 7mm(0.3"), outside diameter 14.5mm(0.6")
find out more

Felt Seal for Series 1 Pedals

Felt Seal for Series 1 Pedals

3.66

Application: Series 1 brake and clutch pedals.
Description: felt seal for brake and clutch pedals. Used with grommet 70620.
Approximate dimensions: 60mm (2.4") long, 44mm (1.7") wide, 15mm (0.6") deep.
find out more

Oil Seal Set for Gearbox

Oil Seal Set for Gearbox

12.58

Application: Series 1, 2 & 3 with 4 or 6 cylinder engine.
Description: Set of oil seals and 'O' rings for main and transfer gearboxes. Includes seals for selector shafts.
find out more

Grommet Series 1 Pedals

Grommet Series 1 Pedals

10.80

Application: Series 1 brake and clutch pedals.
Description: Reproduction rubber grommet for brake pedal shaft to floor panel. Use with 70621 felt seal.
find out more

Oil Seal Differential Pinion

Oil Seal Differential Pinion

5.21

Application: Series 1, 2 & 3 Rover type differentials.

Description: Oil seal to nose of differential. Corteco/Gaco boxed.

Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").

Original part number: 217507.
find out more

Injector Remover TD5

Injector Remover TD5

117.79

Application: TD5 diesel engine as fitted to Defender and Discovery2.
Description: Slide hammer type remover for injectors

find out more

Gasket for Differential to Axle Casing

Gasket for Differential to Axle Casing

0.60

Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
find out more

These Superb Prices are ONLY available when you order ON-LINE

Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Axles and Propshafts for Land Rover Series 2 and 3
Page:   <<   <  1  2  3  4  5  ...   >   >>
Series 3 Hub Bearing Kit Ref: WHEELBRGKIT02
Application: Series 3 1980 onwards, where inner and outer bearings are the same size. Covers both long and short wheel base vehicles, suitable for either front or rear wheel.
Description: Kit of parts to service one wheel hub. Kit comprises a pair of Timken wheel bearings, Gaco inner seal, hub nut locker, flange gasket, 'O' ring outer seal and split pin.

Price: 17.85 (21.42 Including VAT at 20%)




People who bought this item also bought:
1. Axle Set of Brake Shoes - 10" (Ref: STC2796DKIT)
2. Nut and Bolt Kit for Propshafts (Ref: PROPFIX01)
3. Cap for Hub Flange (Ref: 219098)
Series 3 Hub Bearing Kit
Felt Seal Stub Shaft to Drive Flange Ref: RTC3515
Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086

Price: 0.40 (0.48 Including VAT at 20%)




People who bought this item also bought:
1. Flange Gasket (Ref: 231505=)
2. Gasket, front Stub Axle to Swivel Housing (Ref: 277289)
3. Cap for Hub Flange (Ref: 219098)
Felt Seal Stub Shaft to Drive Flange
Land on Stub Axle for Hub Seal Ref: 599698
Application: Series 1 front axle, Series 2 and Series 3 upto 1980.
Description: Replaceable land or spacer on stub axle that the wheel hub seal runs on.
Approximate dimensions: outside diameter 2 5/8"(55.8mm), inside diameter 1 13/16" (46mm), depth 7/16"(11mm).
Original part number: 217351

Price: 7.98 (9.58 Including VAT at 20%)




People who bought this item also bought:
1. Locker for Stub Axle (Ref: 277311D)
2. Series1, 2 & 3 Wheel Bearing Kit with Japanese Bearings (Ref: WHEELBRGKIT01N)
3. Swivel Housing Outer Seal (Ref: RTC3528)
Land on Stub Axle for Hub Seal
Inner Wheel Hub Seal Ref: RTC3510
Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

Price: 3.57 (4.28 Including VAT at 20%)




People who bought this item also bought:
1. Felt Seal Stub Shaft to Drive Flange (Ref: RTC3515)
2. Flange Gasket (Ref: 231505=)
3. Seal Axle Tube (Ref: 217400)
Inner Wheel Hub Seal
Inner Hub Bearing NTN Ref: RTC3416N
Application: Series 1 front hubs, Series 2 & 2A front and rear hubs, Series 3 front and rear hubs to 1980.
Description: Inner wheel hub bearing. NTN (Japanese) taper roller bearing 359S/354X.
Approximate dimensions: outside diameter 85mm (3.35"), inside diameter 46mm (1.8").
Original part number 217269

Price: 18.59 (22.31 Including VAT at 20%)




People who bought this item also bought:
1. Outer Hub Bearing NTN (Ref: RTC3426N)
2. Land on Stub Axle for Hub Seal (Ref: 599698)
3. Locker for Stub Axle (Ref: 277311D)
Inner Hub Bearing NTN
Outer Hub Bearing NTN Ref: RTC3426N
Application: Series 1 front hubs, Series 2 & 2A front and rear hubs, Series 3 front and rear hubs to 1980.
Description: Outer wheel hub bearing. NTN (Japanese) taper roller bearing 11162/11300.
Approximate dimensions: outside diameter 76.5mm (3.0"), inside diameter 41.2mm (1.62").
Original part number 217270

Price: 10.80 (12.96 Including VAT at 20%)




People who bought this item also bought:
1. Brass 'T' Piece for 3/16" Pipes (Ref: ZZHU30)
2. Brass Female Connector (Ref: ZZHU20)
3. Pack of 10 Male Unions for 3/16" Pipe (Ref: ZZHU0110)
Outer Hub Bearing NTN
Locker for Hub Nuts Ref: 217353=
Application: Series 1, 2 & 3. Range Rover Classic and early Defender.
Description: Locker for wheel hub nuts.
Approximate dimensions: outside diameter 64.5mm (2.54"), inside diameter 41.6mm (1.64"), thickness 1.0mm *(0.040")

Price: 0.45 (0.54 Including VAT at 20%)




People who bought this item also bought:
1. Seal Axle Tube (Ref: 217400)
2. Gasket, front Stub Axle to Swivel Housing (Ref: 277289)
3. Grommet - Brake Pipe Support (Ref: 6860L)
Locker for Hub Nuts
Key Washer for Hub Bearing Ref: 217352D
Application: Series 1, Series 2 & Series 3.
Description: Thick keyed washer between outer hub bearing and lock nut.
Approximate dimensions: outside diameter 56mm (2.2"), inside diameter 41.5mm (1.63"), thickness 2.8mm (0.11")

Price: 0.60 (0.72 Including VAT at 20%)




People who bought this item also bought:
1. Inner Wheel Hub Seal (Ref: RTC3510)
2. Retaining Collar Half-Shaft Bearing (Ref: 90217398D)
3. Seal Axle Tube (Ref: 217400)
Key Washer for Hub Bearing
Lock Nut for Hub Bearing Ref: FRC8700D
Application: Series 1, Series 2, Series 3, Range Rover Classic, Discovery 1 and Defender.
Description: Lock nut for hub bearings. Used with second lock nut and locking washer.
Approximate dimensions: 52mm (2 1/16") across flats, thickness 8.5mm (0.33").
Original part number: 217355

Price: 0.85 (1.02 Including VAT at 20%)




People who bought this item also bought:
1. Nut and Bolt Kit for Propshafts (Ref: PROPFIX01)
2. Grommet - Brake Pipe Support (Ref: 6860L)
3. Clip for brake pipe grommet (Ref: 56666)
Lock Nut for Hub Bearing
Flange Gasket Ref: 231505=
Application: Series 1, 2 & £.
Description: Paper gasket for drive flange to wheel hub.
Approximate dimensions: outside diameter 112mm (4.4"), inside diameter 77mm (3")

Price: 0.20 (0.24 Including VAT at 20%)




People who bought this item also bought:
1. Felt Seal Stub Shaft to Drive Flange (Ref: RTC3515)
2. Inner Wheel Hub Seal (Ref: RTC3510)
3. Oil Seal Differential Pinion (Ref: FRC4586)
Flange Gasket
Digital Dispensary > LAND Rover Series 2 & Series 3 Parts > Axles and Propshafts for Land Rover Series 2 and 3
Page:   <<   <  1  2  3  4  5  ...   >   >>

Haven't found what you want? Then try our quotation service.

Main Pages


New Products

Outer Pinion Bearing

Outer Pinion Bearing

10.72

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for outer end of differential pinion gear. Timken bearing numbers HM88046/HM88010

Approximate dimensions: Outside diameter 2.7"(68.5mm), inside diameter 1.25"(31.8mm)., height 0.93"(23.5mm).


find out more

Inner Pinion Bearing - Differential

Inner Pinion Bearing - Differential

21.70

Application: Series 2 from suffix B chassis onwards, Series3 and Classic models where Rover type differentials are fitted.

Description: Timken taper roller bearing for inner end of differential pinion gear. Timken bearing numbers HM801346X/HM801310

Approximate dimensions: Outside diameter 3.25"(82.5mm), inside diameter 1.5"(38mm)., height 1.22"(31mm).

find out more

Seal Kir for 1 1/8" Wheel Cylinders

Seal Kir for 1 1/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for rear wheel cylinders with bore of 1 1/8"(28.5mm). Kit has sufficient seals for both front wheel cylinders.

find out more

Seal Kit for 1 3/8" Wheel Cylinders

Seal Kit for 1 3/8

23.26

Application: Series 1 models 1948 and 1949 for chassis numbers 860001 to 867720.

Descrition: Replacement seals for front wheel cyliders with bore of 1 3/8"(35mm). Kit has sufficient seals for both front wheel cylinders.


find out more

Outlet Nozzle - SU Fuel Pump

Outlet Nozzle - SU Fuel Pump

4.44

Application: Series 1 and early Series 2 models.

Description: Nozzle for outlet of SU fuel pumps. Allows push-on fuel hose connection to pump.

Approximate dimensions: Thread diameter 22mm(0.87"), nozzle diameter 7mm(0.28").

find out more

Wiper Arm Series 3 RH

Wiper Arm Series 3 RH

24.25

Application: Series3 models.

Description: Right hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Wiper Arm Series3 LH

Wiper Arm Series3 LH

24.25

Application: Series3 models.

Description: Left hand wiper arm in stainless steel by Tex Classic.

Approximate dimensions: Overall length 24cm(9.5")

find out more

Door Mirror Left Hand

Door Mirror Left Hand

30.78

Application: Range Rover Classic of the mid 70s.

Description: Reproduction black mirror head by Tex with convex glass.

Approximate dimensions: Head 145mm(5.7") x 90mm(3.5"), mounting holes 38mm(1.5") centres.

find out more

Dingocroft, High Street, Downley, High Wycombe, Bucks. HP13 5XJ. Great Britain

Tel: 01494 448367 Fax: 01494 459964 Company registration number 1163210 (England)
email: sales@dingocroft.co.uk

Copyright © 1997 Penn Rental Service Limited trading as Dingocroft . Suppliers of Land Rover Parts, Land Rover spares and Land Rover accessories. Land Rover Defender parts, Land Rover Freelander parts. Range Rover parts. Range Rover Classic parts. Land Rover Discovery parts. Parts for Land Rover. Parts for Landrover. Land Rover parts UK. E&O -